Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Olivetti OLIBOOKM1020
Summary of Contents for Olivetti OLIBOOKM1020
- Page 3 They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. ©August 2009 Trademarks Intel and Atom are trademarks/registered trademarks of Intel Corporation. Olivetti and Alice are trademarks/registered trademarks of Telecom Italia S.p.A.
- Page 4 Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
-
Page 5: Instructions For Care And Operation
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to Do not place it on an unstable Do not place anything heavy on... - Page 6 Preface Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until Do not turn off any peripheral Do not disassemble the com- Perform routine maintenance...
-
Page 7: Power Safety
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a Power Safety steady, uninterrupted power supply. If you are unsure of your local power specifica- Warning tions, consult your service representative or local power company. -
Page 8: Battery Precautions
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. -
Page 9: Cleaning
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. -
Page 10: Travel Considerations
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. - Page 11 Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Trouble- shooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common.
- Page 12 Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
-
Page 13: Table Of Contents
Table of Contents Contents Notice ................ I TouchPad and Buttons/Mouse ........2-4 Instructions for Care and Operation ......III Audio Features ............2-5 Power Safety ............V Power Management Battery Precautions ..........VI Cleaning ............. VII Overview ..............3-1 Servicing ............. VII Advanced Configuration and Power Interface ..3-1 Travel Considerations ......... - Page 14 Table of Contents Additional Modules Driver Installation ...........4-2 Authorized Driver Message ........4-4 Overview ..............7-1 New Hardware Found ..........4-4 PC Camera Module ..........7-2 Version Conflict Message ........4-4 Wireless LAN Module ..........7-4 BIOS Utilities Troubleshooting Overview ..............5-1 Overview ..............8-1 The Power-On Self Test (POST) .......5-2 Basic Hints and Tips ..........8-2 Failing the POST ...........5-3 Backup and General Maintenance ......8-3...
- Page 15 Table of Contents Specifications Processor ............... C-2 Core Logic ............. C-2 Display ..............C-2 Memory ..............C-2 Video Adapter ............C-2 BIOS ..............C-2 Storage ..............C-2 Security ..............C-2 Audio ..............C-2 Pointing Device ............. C-2 Keyboard .............. C-2 Operating System ..........
- Page 16 Table of Contents...
-
Page 17: About This Quick Guide
Intel and Atom are trademarks/registered trademarks of Intel find this manual refers to the Microsoft Windows XP Home with Corporation. Service Pack 3 operating system. Olivetti and Alice are trademarks/registered trademarks of Telecom Italia S.p.A. About this Quick Guide 1 - 1... -
Page 18: System Map: Front & Rear Views
Quick Start Guide System Map: Front & Rear Views Front Open Shutdown Note that you should always shut your computer down by choosing the Turn Off Com- puter command from the Start menu in Windows. This will help prevent hard disk or system problems. -
Page 19: System Map: Side & Bottom Views
Quick Start Guide System Map: Side & Bottom Views Figure 1-3 - Side & Bottom Views 1. Security Lock Slot External Optical Device 2. DC-In Jack Drives 3. RJ-45 LAN Jack 4. 2 * USB 2.0 Ports To install applications and driv- Left 5. -
Page 20: Led Indicators
Quick Start Guide LED Indicators The LED indicators on the computer display helpful information about the current status of the computer. Icon Color Description Orange DC Power is Plugged In Green The Computer is On Blinking Green The Computer is in Sleep Mode Orange The Battery is Charging Green... -
Page 21: Keyboard & Function Keys
Quick Start Guide Keyboard & Function Keys Keypad The keyboard has a numeric keypad for easy numeric data input. Pressing Function Keys NumLk & the Fn +NumLk keys turns on/off the numeric keypad. It also features ScrLk function keys to allow you to change operational features instantly. The function keys (F1 - F12 etc.) will act as hot keys when pressed while Numeric the Fn key is held down. -
Page 22: Driver Installation
Quick Start Guide Driver Installation The Device Drivers & User’s Manual disc contains the drivers necessary for the proper operation of the computer. This setup has already been done for you. If for any reason you need to Driver Installation General reinstall the drivers , insert the disc and browse the Driver Folder to locate the driver you need. -
Page 23: Features & Components
Features & Components Chapter 2: Features & Components Overview Read this chapter to learn more about the following main features and compo- nents of the computer: • Hard Disk Drive • 7-in-1 Card Reader • TouchPad and Buttons/Mouse • Audio Features •... -
Page 24: Hard Disk Drive
Features & Components Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken Power Safety out to accommodate other 2.5" serial (SATA) HDDs with a height of 9.5 mm. The HDD is located in the bay on the right of your computer, and this can be opened after Before attempting to ac- elevating the keyboard and accessing the screw securing the hard disk assembly. -
Page 25: 7-In-1 Card Reader
Features & Components 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push Card Reader Cover the card into the slot and it will appear as a removable device, and can be ac- cessed in the same way as your hard disk (s). -
Page 26: Touchpad And Buttons/Mouse
Features & Components TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a Mouse Driver mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. Make sure you have If you are using an exter- installed the TouchPad driver. -
Page 27: Audio Features
Features & Components Audio Features You can configure the audio options on your computer from the Sounds and Sound Volume Audio Devices Windows control panel, or from the Realtek HD Audio Adjustment Manager icon in the taskbar/control panel (this will bring up the Realtek Au- dio Configuration menus). - Page 28 Features & Components Audio Recording from Microphone If you want to record from either the built-in microphone or an external micro- phone, then configure the audio options as follows: Double-click the Realtek HD Audio Manager icon in the taskbar/control panel. Click Mixer (tab).
-
Page 29: Power Management
Power Management Chapter 3: Power Management Overview OS Note Power management To conserve power, especially when using the battery, your computer power functions will vary slightly management conserves power by controlling individual components of the depending on your oper- computer (the monitor and hard disk drive) or the whole system. This chapter ating system. -
Page 30: The Power Sources
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/DC adapter will damage the computer and its components. Attach the AC/DC adapter to the DC-in jack on the left of the computer. -
Page 31: Turning On The Computer
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the Shutdown power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hiber- Note that you should al- nate/Shutdown hot-key button when it is pressed for less than 4 seconds ways shut your computer... -
Page 32: Power Schemes
Power Management Power Schemes You can set your computer to conserve power through individual components by Resuming Operation means of Power Schemes. You can also adjust the settings for each scheme to set the monitor to turn off after a specified time, and the computer's hard disk motor Press a key on the key- to turn off if the hard disk drive has not been accessed for a specified period of time board,... - Page 33 Power Management Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
-
Page 34: System Power Options
Power Management System Power Options You can use the system power options to stop the computer’s operation and Stand by/Hibernate restart where you left off. This system features Stand by and Hibernate sleep or Shutdown Error mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - see Figure 3 - 2 on The computer may stop... - Page 35 Power Management Stand by Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to System Resume idle at its slowest speed. All open applications are retained in memory. When you The system can resume are not using your computer for a certain length of time, which you specify in the from Stand by mode by:...
-
Page 36: Configuring The Power Button
Power Management Configuring the Power Button The power button may be set to send the computer in to either Stand by or Sleep Button Hibernate mode. In Stand by mode, the LED will blink green. In Hiber- nate mode the LED will be off (battery) or orange (AC/DC adapter). If you are You may also configure in a power saving mode set to save power through individual components (e.g. -
Page 37: Battery Information
Power Management Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery New Battery Warning Always completely discharge, then fully charge, a new battery (see “Battery When the battery is criti- FAQ” on page 3 - 12 for instructions on how to do this). -
Page 38: Recharging The Battery With The Ac/Dc Adapter
Power Management Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. Conserving Battery Power We recommend that you do not remove the battery yourself. If you need to re- move the battery for any reason, see “Removing the Battery”... - Page 39 Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g.
-
Page 40: Battery Faq
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Caution Don’t turn off the computer by yourself even when you see a message that in- Danger of explosion if dicates the battery is critically low, just let the computer use up all of the battery battery is incorrectly re-... -
Page 41: Drivers
Drivers Chapter 4: Drivers What to Install This chapter deals with installing the drivers a essen- tial to the operation or improvement of some of the The Device Drivers & User’s Manual disc contains computer’s subsystems. The system takes advantage the drivers necessary for the proper operation of the of some newer hardware components for which the computer. -
Page 42: Driver Installation
Drivers Driver Installation From “my Computer” select the CD/DVD unit con- tainning the Device Drivers & User’s Manual disc. Driver - Windows XP with Service Pack 3 RightClick and select Browse . Open the Drivers folder and and browse to the exe- Chipset cutable file ( “Setup.exe”... - Page 43 Drivers Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest se- Windows XP Service Pack 3 curity updates etc. (all updates will include the lat- Make sure you install Windows XP Service Pack 3 (or a est hotfixes from Microsoft).
-
Page 44: Authorized Driver Message
Drivers Authorized Driver Message Updating/Reinstalling Individual Drivers If you receive a message telling you that the driver you If you wish to update/reinstall individual drivers it may are installing is not authorized (Digital Signature be necessary to uninstall the original driver.To do this Not Found), just click Yes or Continue Anyway to go to the Control Panel in the Windows OS and ignore the message and continue the installation pro-... -
Page 45: Bios Utilities
BIOS Utilities Chapter 5: BIOS Utilities Overview BIOS Settings Warning This chapter gives a brief introduction to the computer’s built-in software: Incorrect settings cause your system to Diagnostics: The POST (Power-On Self Test) malfunction. To correct mistakes, return to Setup Configuration: The Phoenix TrustedCore Setup Utility and restore the Setup Defaults with <F9>. -
Page 46: The Power-On Self Test (Post)
BIOS Utilities The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to con- POST Screen duct a POST, including a quick test of the on-board RAM (memory). 1.BIOS information As the POST proceeds, the computer will tell you if there is anything wrong. If 2.CPU type there is a problem that prevents the system from booting, it will display a sys- 3.Memory status... -
Page 47: Failing The Post
BIOS Utilities Phoenix TrustedCore(tm) NB Copyright 1985-2006 Phoenix Technologies Ltd. All Rights Reserved Bios Revision: ******** KBC/EC Firmware Revision: ******** CPU = 1 Processors Detected Intel(R) Atom(TM) CPU N270 @ 1.60GHz 1015M System RAM Passed 512 KB L2 Cache System BIOS shadowed Video BIOS shadowed Fixed Disk 0: FUJITSU MHY2120BH Mouse intialized... -
Page 48: The Setup Utility
BIOS Utilities Non-Fatal Errors This kind of error still allows you to boot. You will get a message identifying the problem (make a note of this message!) followed by the prompt: • Press <F1> to resume • <F2> to enter Setup Press F1 to see if the boot process can continue. -
Page 49: Setup Screens
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Phoenix TrustedCore Setup Utility. Setup Menus The Setup menus shown Along the top of the screen is a menu bar with menu headings. When you se- in this section are for ref- lect a heading, a new screen appears. -
Page 50: Main Menu
BIOS Utilities Main Menu Phoenix TrustedCore(tm) Setup Utility Figure 5 - 2 Main Main Advanced Security Boot Exit Main Menu Item Specific Help System Time: [22:12:05] System Date: [02/18/2009] <Tab>, <Shift Tab>, or SATA Port 1 [FUJITSU MHV2120BH-(S] <Enter> selects field. System Memory 640 KB Extended Memory... - Page 51 BIOS Utilities SATA Port 1 (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a HDD on the computer’s Serial ATA Port 1. Use the Auto (Type:) setting to have the items configured automatically for you. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user config- urable.
-
Page 52: Advanced Menu
BIOS Utilities Advanced Menu Phoenix TrustedCore(tm) Setup Utility Main A A dvanced Advanced Security Boot Exit Item Specific Help Legacy USB Support: [Enabled] Boot-time Diagnostic Screen: [Disabled] Enable support for Reset Configuration Data: [No] Legacy Universal Serial Power On Boot Beep [Disabled] Figure 5 - 3 Bus. - Page 53 BIOS Utilities Reset Configuration Data (Advanced Menu) This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot. Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up.
-
Page 54: Security Menu
BIOS Utilities Security Menu Phoenix TrustedCore(tm) Setup Utility Security Menu Main Advanced Security S S e e c c u u r r i i t t y y Boot Exit Item Specific Help The changes you make Supervisor Password Is: Clear here affect the access User Password Is:... - Page 55 BIOS Utilities Set User Password (Security Menu) You can set a password for user mode access to the Phoenix SecureCore Set- up Utility. This will not affect access to the computer OS, (only the Setup util- Password Warning ity) unless you choose to set a Password on Boot (see below). Many menu items in the Phoenix SecureCore Setup Utility cannot be modified in user If you set a boot pass- word (Password on boot...
-
Page 56: Boot Menu
BIOS Utilities Boot Menu Phoenix TrustedCore(tm) Setup Utility Figure 5 - 5 Main Advanced Security Boot Exit Boot Menu Item Specific Help Boot priority order: USB HDD: Keys used to view or USB CDROM: IDE CD: configure devices: IDE HDD: FUJITSU MHY212BH-(S1) Up and Down arrows USB KEY: select a device. -
Page 57: Exit Menu
BIOS Utilities Exit Menu Figure 5 - 6 Phoenix TrustedCore(tm) Setup Utility Main Advanced Security Boot Exit Exit Menu Item Specific Help Exit Saving Changes Exit Discarding Changes Exit System Setup and Load Setup Defaults save your changes to CMOS. Discard Changes Save Changes Help... - Page 58 BIOS Utilities 5 - 14...
-
Page 59: Upgrading The Computer
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps Warranty Warning outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help. Before you begin you Please check with your will need: service representative be-... -
Page 60: When Not To Upgrade
Upgrading The Computer When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes re- placing parts. Power Safety Warning You should not perform any of these upgrades if: Before you undertake any upgrade procedures, • Your system is still under warranty or a service contract make sure that you have •... -
Page 61: Removing The Battery
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety rea- Warranty Warning sons it is best to remove the battery. Turn the computer off, and turn it over. Please check with your service representative be- Slide the latches in the direction of the arrows to unlock the battery. -
Page 62: Upgrading The Hdd
Upgrading The Computer Upgrading the HDD The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) HDD System HDDs with a height of 9.5mm (h) and a speed of 5400 RPM or lower. Follow Warning your operating system’s installation instructions, and install all necessary drivers and utilities (see “Driver Installation”... - Page 63 Upgrading The Computer Carefully lift the hard disk assembly up out of the bay. Hard Disk Drive Speeds If you are going to up- grade/replace the hard disk drive, note that It is recommended that HDDs of a maximum speed of 5400 RPM are used.
- Page 64 Upgrading The Computer Secure the disk with the four screws and then reinsert the hard disk assembly into the computer’s hard disk bay. Replace the hard disk bay screw (see Figure 6 - 3 on page 6 - 6 - 6...
-
Page 65: Upgrading The System Memory (Ram)
Upgrading The Computer Upgrading the System Memory (RAM) The computer has one memory socket for 200 pin Small Outline Dual In-line (SO-DIMM) DDRII (DDR2) type memory modules (see “Memory” on page C for details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer. - Page 66 Upgrading The Computer Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( & Figure 6 - Figure 6 - 6 RAM Module Release Latches Contact Warning Be careful not to touch the metal pins on the module’s connecting...
- Page 67 Upgrading The Computer Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. The module’s pin alignment will allow it to only fit one way. Make sure the module is Re-Inserting the seated as far into the slot as it will go.
-
Page 68: Upgrading The Processor
Upgrading The Computer Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with Warranty a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly The CPU is not a user ser- you may damage the processor or mainboard. -
Page 69: Additional Modules
Additional Modules Chapter 7: Additional Modules Overview Wireless Device Operation Aboard This chapter contains information on the following modules, which come with Aircraft your computer. The use of any portable • PC Camera Module electronic transmission • Wireless LAN Module devices aboard aircraft is usually prohibited. -
Page 70: Pc Camera Module
Additional Modules PC Camera Module Taking Still Pictures Use the Fn + F10 key combination (see “Function/Hot Key Indicators” on Chapter 1) to toggle power to the PC Camera module. Double-click Computer icon on the The PC camera is supported by the embedded Windows drivers . desktop, or go the Start The Device Drivers &... - Page 71 Additional Modules PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-click the Sounds &...
-
Page 72: Wireless Lan Module
Additional Modules Wireless LAN Module Make sure that the Wireless LAN module is on before installing the driver (the Wireless Device WLAN module’s default power state is off). Operation Aboard Aircraft Use the Fn + F11 key combination (see “Function/Hot Key Indicators” on Chapter 1) to toggle power to the Wireless LAN module. - Page 73 Additional Modules 802.11b/g or 802.11n WLAN Driver Installation 1. Make sure the module is powered on, and then insert the Device Network Drivers & User’s Manual disc into the CD/DVD drive. Connection 2. Browse the CD and go to the Drivers / WLAN folder . Use the Windows Net- 3.
- Page 74 Additional Modules 8. Access any available wireless networks from Network Connections > Wireless Network Connection menu in Windows (or click the icon in the taskbar), and click View Wireless Connections. 7 - 6 Wireless LAN Module...
-
Page 75: Troubleshooting
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possi- ble solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface. -
Page 76: Basic Hints And Tips
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your com- puter appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. -
Page 77: Backup And General Maintenance
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. -
Page 78: Viruses
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seri- ously harm your computer and cause you to lose data. Anti-Virus programs are commercially avail- able and the definitions file updates are usually downloadable directly from the internet. -
Page 79: Upgrading And Adding New Hardware/Software
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. -
Page 80: Problems And Possible Solutions
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t Battery missing / incorrectly installed. Check the battery bay, make sure the battery work. is present and seated properly (the design of the battery only allows it to go in one way). - Page 81 Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface. Make sure you’re using the correct adapter.
- Page 82 Troubleshooting Problem Possible Cause - Solution No image appears on the external You haven’t installed the video driver and configured it appropriately from the monitor I have plugged in and powered on. Control Panel. See “Display Devices & Options” on page B - 5 for instructions on installing and configuring the video driver.
- Page 83 Troubleshooting Problem Possible Cause - Solution Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work. The system freezes or the screen goes The system’s power saving features have timed-out.
- Page 84 Troubleshooting Problem Possible Cause - Solution The Wireless LANor PC Camera modules The driver(s) for the module(s) have not been installed. Make sure you have cannot be configured. installed the driver for the appropriate module (see the instructions for the appropriate module in “Additional modules”...
-
Page 85: Interface (Ports & Jacks)
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your com- puter to communicate with external devices, connect to the internet etc. Interface (Ports &... -
Page 86: Notebook Ports And Jacks
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. - Page 87 Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
- Page 88 Interface (Ports & Jacks) A - 4 Interface (Ports & Jacks)
-
Page 89: Intel Video Driver Controls
Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” sec- tion. Intel Video Driver Installation DVMT Notes Make sure you install all the drivers in the order indicated in Table 4 - 1, on DVMT is not local video page 4 - memory. -
Page 90: Intel Graphics Properties
Intel Graphics Properties More advanced video configuration options are provided by the Intel(R) Taskbar Icon Graphics Media Accelerator Driver for Mobile. Open Display Propertiesand click Advanced. You can also access the Click the Intel(R)... tab and click Graphics Properties (button). controller properties You can also access Graphics Properties from the Windows Intel(R) GMA Driver... - Page 91 You may make changes to the devices, color, schemes, Hot Keys etc. by click- ing the appropriate menu item or button. Help Menus Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click “What’s This?”...
-
Page 92: Scheme Options
Scheme Options Use Scheme Options to configure quick settings for applications which re- quire specific resolution and color settings in order to run properly e.g. games, Application.exe multimedia programs. To set the scheme options: You will need to locate Go to the Graphics Properties control panel (see the actual application “Intel Graphics Properties”... -
Page 93: Display Devices & Options
Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT) or external Flat Panel Display as your display device. A VGA monitor/Flat Panel Function Key Combination Display connects to the external monitor port. The following display modes are available. -
Page 94: Attaching Other Displays
Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the external Multiple Display monitor port on the left of the computer. At least one other display To Enable Intel(R) Dual Display Clone Mode must be attached in or- Attach your external display to the external monitor port, and turn it on. - Page 95 To Enable Extended Desktop Mode: Attach your external display to the external monitor port, and turn it on. Go to the Intel(R) GMA Driver for mobile control panel and click Display Devices. Display Settings Click to choose Extended Desktop (Multiple Display). Extended Desktop Click Apply, and OK to confirm the settings change.
- Page 96 To Enable Extended Desktop (Windows Display Properties) Attach your external monitor to the external monitor port, and turn it on. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you Display Settings are in Category View choose Appearance and Themes). Extended Desktop Double-click Display (icon).
-
Page 97: Specifications
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds) may be changed, delayed or updated due to the manufacturer's release schedule. Check with your service center for details. -
Page 98: Processor
Specifications Processor Video Adapter Audio Intel® Atom® Processor N270 Intel 945GSE Integrated Video High Definition Audio Compliant Interface (1.6 GHz 512KB On-die L2 Cache & Compliant with Microsoft UAA (Universal Supports DirectX 9.0 533MHz FSB - BGA Package) Audio Architecture) Shared Memory Architecture Direct Sound 3D™... -
Page 99: Operating System
Specifications Communication Slot Dimensions & Weight 10Mb/100Mb Base-T Ethernet LAN Two Mini-Card Slots (USB & PCIE) 271mm (w) * 188.6mm (d) * 19.5 - 28mm (h) Slot 1: for Wireless LAN Module (Half Mini- Around 1.2 kg With Battery 802.11b/g Wireless LAN Half Mini-Card Card) Module 1.3M Pixel USB PC Camera Module... - Page 100 Specifications C - 4...