Summary of Contents for Audio Analogue SRL Audio Analogue SRL
- Page 1 AUDIO ANALOGUE soundpleasure puccini INTEGRATED AMPLIFIER OWNER’S MANUAL MANUALE D’ISTRUZIONI...
- Page 3 PAGE/PAGINA...
-
Page 4: Apertura Dell'imballo
INSTALLATION INSTALLAZIONE UNPACKING The shipping box should contain the following items apart from the amplifier and this APERTURA DELL’IMBALLO owner's manual: Remote control Two AAA size batteries AC power cord Warranty certificate Please check if all has been included: if not, contact your dealer. After opening the box, carefully extract the amplifier and remove its protective plastic bag;... - Page 5 CONTROLS Remote IR Sensor Sensore IR del telecomando Aim remote control to this window to remotely operate the amplifier. COMANDI Puntare il telecomando verso questa finestrella per agire da lontano sui comandi dell’amplificatore. Power / Standby /Fault Indicator - Spia di Alimentazione / Standby / Guasto Lights green when unit is powered up and operating.
- Page 6 CONNECTIONS Phono Ground / Massa Giradischi Binding post for the turntable's earth wire. COLLEGAMENTI Collegamento per il filo di masso del giradischi. Phono Input (PH1) / Ingresso Phono (PH1) Uncommon on most of today's amplifiers, the Puccini special edition offers an on- board phono preamplifier capable of interfacing both Moving Magnet and high-level Moving Coil cartridges (MM) and low-level Moving Coil cartridges (MC).
-
Page 7: Collegamento Dei Diffusori
INPUT CONNECTIONS COLLEGAMENTI DEGLI INGRESSI TAPE OUT CONNECTION COLLEGAMENTO DELL’USCITA TAPE PRE OUT CONNECTION COLLEGAMENTO DELL’USCITA PRE PRE OUTPUT SWITCH INTERRUTTORE DELL’USCITA TAPE SPEAKER CONNECTION COLLEGAMENTO DEI DIFFUSORI BI-WIRING The amplifier has six pairs of source input RCA sockets (one phono and five high-level line). -
Page 8: Operation
OPERATION Once all connections have been correctly made (please check twice!), make sure the volume control is turned completely anticlockwise then turn the unit on by pressing the FUNZIONAMENTO power switch near the IEC socket on the rear panel. On the front panel, the power indicator will glow red to indicate that the unit is in the power-up standby. - Page 9 BURN-IN Long and exhaustive listening tests have shown that the best sonic performance is PERIODO DI RODAGGIO obtained after a "burn-in" period of at least 100 hours. Once the unit is fully "burnt-in", best sound quality can be obtained after about 40 minutes warming up. Lunghe e complete prove d'ascolto hanno dimostrato che le migliori prestazioni sonore si otterranno dopo un periodo di "rodaggio"...
- Page 10 REMOTE CONTROL Press to select next source. Pressing IN+ when source 6 is selected gives source PH1. TELECOMANDO Premere per selezionare la sorgente successiva. Quando è selezionata la sorgente 6, la pressione di IN+ seleziona la sorgente PH1. Press to select previous source. Pressing IN- when source PH1 is selected gives source 6. Premere per selezionare la sorgente precedente.
-
Page 11: Safety Precautions And Maintenance
SAFETY Avoid opening the unit - No further servicing than that described in this manual should be attempted. Refer all servicing to authorised Audio Analogue dealers and qualified PRECAUTIONS AND technicians. MAINTENANCE Do not expose the unit to heat - Keep it away from heat sources such as direct sun, cookers, radiators, etc.. -
Page 12: Specifiche Tecniche
PUCCINI INTEGRATED AMPLIFIER Output power (1kHz/230VAC/ both channels driven) SPECIFICATIONS SPECIFICHE TECNICHE Potenza d'uscita (1kHz/230VAC/ entrambi i canali attivi) 2 x 55W / 8 2 X 85W / 4 Line Input Impedance Impedenza Ingressi Linea Phono Input Impedance Impedenza Ingressi Phono MM 47K / 220pF;... - Page 13 Slew Rate Slew Rate > 10V/s Bandwidth ( 0.1dB) Banda passante ( 0,1dB) 20Hz-20kHz Bandwidth ( 3dB) Banda passante ( 3dB) 5Hz-200kHz (1W / 8 ) Channel Separation (a 1kHz, unused input shorted) Separazione tra i canali (a 1kHz, ing. non usato a 0 Inputs Ingressi MM/MC Phono (PH1), Line 1/6...
- Page 14 Power led off SYMPTOM No sound CAUSE Power cord incorrectly inserted and/or amplifier switched off REMEDY Check that cord is inserted both in the integrated amplifier and in the mains wall socket and that the switch is in the 'ON' position Fuse burnt out CAUSE Check the fuse in the fuse holder (unplug cord from mains first!!) next to the IEC socket...
-
Page 15: Ricerca Guasti
RICERCA GUASTI Led 'Power' spento SINTOMO Nessun suono CAUSA Cordone d'alimentazione non inserito correttamente e/o amplificatore spento Controllate che il cordone sia ben inserito nell'amplificatore e nella presa di rete a muro, RIMEDIO e che l'interruttore sia nella posizione 'ON' Fusibile bruciato CAUSA Controllate il fusibile nel portafusibili (dopo aver staccato il cordone dalla presa!!) - Page 16 audio analogue Head Office / Ufficio commerciale: srl Via C. Bottai, 88B 51015 Monsummano Terme (PT) Italy tel. (+39) 0572 954513 · fax (+39) 0572 958099 e-mail: info@audioanalogue.com R&D Laboratory / Laboratorio ricerca e sviluppo: Via XX Settembre, 12 56017 San Giuliano Terme (PI) Italy www.audioanalogue.com info@audioanalogue.com soundpleasure...
Need help?
Do you have a question about the Audio Analogue SRL and is the answer not in the manual?
Questions and answers