Pioneer DV-59AVI Operating Instructions Manual page 72

09 Additiona
Problem
U).fm 96 ページ ２００３年８月２０日 水曜日 午後６時４６分
Playback starts
automatically when the
input function of the AV
receiver is changed to this
player.
A connected i.LINK
component doesn't work
with this player.
i.LINK-related messages
ditional inf
You may see the following messages
ubleshooting
年８月２０日 水曜日 午後６時４６分
displayed in the front panel display when
using the i.LINK interface.
Remedy
udio output. • If the front panel HDMI indicator is lit:
LINK CHECK
– You won't hear any sound from the HDMI output if the source
The player is checking the i.LINK network. It
component is only DVI/HDCP-compatible.
does this, for example, when components are
– It is not possible to output SACD or copy-controlled DVD-Audio
added or removed from the network. The
CPPM sources from the HDMI connection.
sound may be interrupted if this happens
• If the front panel i.LINK indicator is unlit then:
during playback.
– Make sure that you've selected this player as the HDMI input in the
settings for the component you're using. You may need to refer to the
PQLS ON
instruction manual of the component to do this.
Displayed when the player receives a rate
後６時４６分
– Check that the HDMI cable is connected properly and that the cable
control on request from the receiver during
isn't damaged.
is output during slow motion playback or when scanning
playback. The sound may be interrupted
– Check that components connected using the HDMI interface are
than audio CDs
momentarily when this happens.
switched on and HDMI compatible. (
D discs do not output digital audio: Switch your amplifier
Note that the PQLS feature works only when
be made with components compatible with both DVI and High
r's analog outputs.
the player is connected to a single receiver.
Bandwidth Digital Content Protection (HDCP).)
at the disc is free from dust and dirt, and that it is not
– Check that the
aking care of your player and discs on page 81).
PQLS OFF PURE AUDIO
at all interconnects are firmly inserted.
at the plugs and terminals are free of dirt, oxide, etc. and Displayed when the player receives a rate
deo output • Make sure that you've selected this player as the HDMI input in the
control off request from the receiver during
essary. Also check the cable for damage.
settings for the component you're using. You may need to refer to the
e the player's output is not connected to the amplifier's playback. The sound may be interrupted
instruction manual of the component to do this.
momentarily when this happens.
table) inputs.
• It is not possible to output SACD or copy-controlled DVD-Audio
ur amplifier/receiver's settings (volume, input function,
CPPM sources from the HDMI connection.
tings, etc.).
ction. If you think that there is some-
LOOP CONNECT
• Check that the HDMI cable is connected properly and that the cable
Sometimes the trouble may lie in
The i.LINK network cannot function because
isn't damaged.
ctrical appliances being used. If the
it is connected in a loop (see Creating an
e that the Digital Out setting is set to On (see Digital Out
• Check that components connected using the HDMI interface are
98
ask your nearest Pioneer authorized
i.LINK network on page 22).
.
switched on and HDMI compatible. (
at the Dolby Digital , DTS and MPEG Out settings (see
be made with components compatible with both DVI and High
o Out settings on page 63) are suitable for your amplifier/
Bandwidth Digital Content Protection (HDCP).)
heck the instruction manual that came with your
• Check that the
ceiver.
PURE AUDIO
Downloaded From DvDPlayer-Manual.com Pioneer Manuals
nd some DVD-Audio discs do not output digital audio.
En
• Make sure the resolution on this player matches that of the
ugh the player's analog audio outputs.
m dirt and dust and is not damaged
component you have connected using HDMI. See HDMI Settings
Remedy
• This is an i.LINK feature and not a malfunction.
• Depending on the connected component, this player may not work
properly with it. See also the operating instructions that came with the
other component.
An HDMI connection can only
PURE AUDIO
indicator is not lit. If it is, press the
See also Front panel
button (
An HDMI connection can only
PURE AUDIO
indicator is not lit. If it is, press the
button ( See also Front panel
BUS FULL
The i.LINK bus has reached its capacity and
cannot transmit any more data.
• Static electricity or other external influ-
ences may cause malfunctioning of this
unit. In this case, unplug the power cord
and then plug back in. This will usually
reset the unit for proper operation. If this
does not correct the problem, please
consult your nearest Pioneer service
center.
on page 26).
on page 26).