Table of Contents
Advertisement
POWER SOURCE
This unit operates on 8 X 'C' (UM‐2) size batteries or from
A. DC POWER OPERATION
1.
Open the Battery Door
2.
Insert 8 "C" (UM‐2) size batteries (not included) according to the polarity diagram on the back cabinet.
3.
Close the Battery Door
IMPORTANT:
Be sure that the batteries are installed correctly. Wrong polarity may damage the unit.
Note: For better performance and longer operating time, we recommend the use of alkaline‐type batteries.
(a) Do not mix old and new batteries.
(b) Do not mix alkaline, standard (carbon‐zinc) or rechargeable (nickel‐cadmium) batteries.
If the unit is not to be used for an extended period of time, remove the battery. Old or leaking battery can
cause damage to the unit and may void the warranty.
B. AC OPERATION
1. Connect the included AC Power Cord to the AC Mains
2. Connect the other end of the AC Power Cord to a wall outlet with
CD PLAYER OPERATION
1.
Set the Function Selector
2.
Open the CD Door (#18). Place an audio CD with its label side upward in the CD compartment and close
the CD Door.
3.
After a few seconds, the total number of tracks on the CD will appear in the CD Track Display
4.
Press the CD PLAY/PAUSE Button
Display will light steadily.
5.
Adjust the Volume Control
6.
To suspend playing, press the CD PALY/PAUSE Button (#11). The CD Track Display will flash. To resume
playing, press the CD PLAY/PAUSE
7.
You can choose to play your favorite track directly by pressing the CD FWD Skip Button
or CD REV Skip Button
number selected.
8.
To repeat playing a particular track, press the REPEAT Button
Track Display will flash.
9.
To repeat playing the entire
Display will light steady.
10. To stop playing, press the CD STOP Button (#5).
11. When you wish to turn off the CD Player, set the Function Selector
CD PROGRAMMED PLAY
This function allows the tracks to be played in a programmed sequence.
1.
Under CD stop condition, press the PROG. Button (#4). The CD Track Display
PROG/PLAY/PAUSE Indicator
2.
Press the CD FWD Skip Button
3.
Press the PROG. Button (#4) again to store selection. The CD Track Display
4.
Press the CD FWD Skip Button
and press the PROG. Button to store selection.
5.
You may repeat steps #2 ‐ #3 to program as many as
tracks, the CD Track Display
entry!
6.
Press CD STOP Button
7.
To check the programmed tracks, press PROG. Button
The CD Track Display
number.
(#18).
(#18).
(#2)
to the "CD" position.
(#11)
and the CD will start playing from the first track. The CD Track
(#3)
to obtain the desired sound level from the Speakers
Button(#11)
(#15)
to skip backward. The CD Track Display
, ,
CD,
press the REPEAT Button
(#20)
will flash.
(#15)
or CD REV Skip Button
(#15)
or CD REV Skip Button
(#6)
will revert to "01" and the old entry will be overwritten by the current new
(#5)
to end programming and return to normal play mode.
(#6)
will display the program number first and then followed by the flashing track
AC120V/60Hz
line power supply.
(#17)
on the back of the unit.
AC120V/60Hz
again.
(#12)
once. The Repeat Indicator in the CD
(#12)
twice. The Repeat Indicator in the CD Track
(#2)
(#15)
to select the song to be programmed.
(#15)
to select the next song to be programmed
20
tracks. If you attempt to program more than
(#4)
continuous to show all the programmed songs.
5
power supply.
(#16).
(#15)
to skip forward
(#6)
will indicate the correct track
to the "OFF" position.
(#6)
will display "01" and the
(#6)
will advance to "02".
(#6).
20
Advertisement
Table of Contents
