Page 1: Table Of Contents
WWhip Long-Range Wi-Fi Receiver Introduction 1 - 2 Register your Product Theory of Operation Installation 3 - 4 You will Need Parts in the Illustration Mounting Options Quick Install Guide Power Supply Usage 5 - 9 Initial Setup Connect To A Network Changing the password WIFI-1 Troubleshooting...
Page 2: Introduction
INTRODUCTION Register your Product Warranty Please register your product for warranty and notiﬁcations for available software updates at: http://shakespeare-ce.com/marine/register/ Scan the below QR code See label under the device with the end cap removed for MAC ID Page 1 WIFI-1 / WebWhip Wi-Fi Receiver Kit ™...
Page 3: Theory Of Operation
INTRODUCTION INTRODUCTION Congratulations on purchasing the WebWhip™, our fully integrated Wi-Fi antenna, receiver and router, for hassle-free internet reception on your boat, RV, cabin or AnyWhere else. ® The WebWhip is designed in partnership with Ubiquiti Networks , a leader in ®...
Page 4: Installation
INSTALLATION INTRODUCTION INTRODUCTION You will Need: 1. WebWhip kit 2. Plug travel adapter (if using in any other country other than the US) 3. Pliers (For rail or post installation. Refer mounting options below) 4. Screws and Screw driver (For surface mounting. Refer mounting options below) 5.
Page 5: Quick Install Guide
INSTALLATION Mount the L-bracket onto the mounting surface using one of the three options listed in the “Mounting Options” section of this manual. Assemble the antenna onto the L-bracket using the hex-nut. Tighten the hex-nut using pliers/ wrench. Quick Assemble the Wi-Fi Radio onto the antenna from the bottom by screwing on its Coupling Ring onto the threads of the antenna.
Page 6: Usage
USAGE INTRODUCTION Warning: Avoid using this product in a lightning storm. There may be a remote risk of electrical shock or damage to the product. Initial Setup (First time only or if network settings have been changed recently): 1. If your laptop is connected to the WebWhip via an ethernet cable, ensure that Wi-Fi is disabled on your laptop (Not just disconnected).
Page 7: Connect To A Network
USAGE 3. Follow instructions in “Connect To A Network” section of this document A: Connect To A Network: 1. Ensure that the laptop is connected to the WebWhip via an Ethernet cable or wireless router. 2. If your laptop is connected to the WebWhip via an ethernet cable, ensure that Wi-Fi is disabled on your laptop (Not just disconnected).
Page 8 USAGE INTRODUCTION 3. Follow on-screen instructions to login Default username: ubnt Default password: ubnt Tip: Save login details to browser for fast access. 4. Under the “WIRELESS” tab, choose the network that you want to connect to by doing the following: A.
Page 9: Changing The Password
USAGE 6. Close the tab and you are ready to go! B: Changing The Password: 1. If you have forgotten your password, follow the instructions in the factory reset section of this manual. Before doing so, you may try the default password to verify if you did not change the password earlier.
Page 10: Troubleshooting
TROUBLESHOOTING INTRODUCTION A: Conduct A Factory Reset: 1. Follow steps 5-10 of the Quick Install guide to connect the WebWhip to a laptop, via an Ethernet cable. 2. With the device connected to the power and a laptop, push reset button under device and hold for about 10 secs until lights blink.
Page 11 TROUBLESHOOTING You can ﬁnd it under: Mac: System Preferences > Network > Ethernet or Wi-Fi (If connected through a wireless router) > Conﬁgure IPv4: Using DHCP Control Panel > Network and Sharing Centre > Local Area Connection > Properties 5. Open a web browser and enter 192.168.1.20 in the address bar. Press the enter or return key, to open the login page..
Page 12 TROUBLESHOOTING INTRODUCTION 6. In the “NETWORK” tab, make the following changes: A. Network Role > Network Mode: Router B. WAN Network Settings> NAT: Enable C. LAN Network Settings> DHCP Server: Enable D. LAN Network Settings> IP Address: 192.168.1.20 E. LAN Network Settings> Range Start: 192.168.1.30 7.
Page 13: Technical Support
TECHNICAL SUPPORT Contact us For product information or for installation questions please contact our customer service American Operations: European Operations: 6111 Shakespeare Rd. Enterprise Way, Fleetwood, Columbia, SC 29223 Lancanshire, FY7 8RY, England Toll Free: 1-800-845-7750 Phone: +44 (0) 1253-858787 Page 12 WIFI-1 / WebWhip Wi-Fi Receiver Kit...
Page 14: Compliance Information
COMPLIANCE INFORMATION Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 15: Compliance Information
COMPLIANCE INFORMATION CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. Alert Sign (!) Follows CE Marking Alert sign must be indicated if a restriction on use applied to the product and it must follow the CE marking.
Page 16 Receiver Technical Specs WIFI-1 Model No. 2.4GHz, 802.11 b/g/n Frequency and Wireless Standards Up to 28dBm Radio Power Antenna Gain Up to 7 Miles* Range 100+ Mbps Throughput 25ft (7.62m) Ethernet cable Wire N-Female (Antenna), Ethernet (Device) Connectors 12VDC & 110/220VAC, 600mA Max at 12VDC Power Supply &...