Summary of Contents for Aegis AEG-WR
- Page 1 Model AEG-WR Wireless Receiver Installation Manual Downloaded from - http://www.guardianalarms.net...
-
Page 2: Table Of Contents
CONTENTS DESCRIPTION COMPATIBLE TRANSMITTERS INSTALLATION OPERATION RESET MEMORY AEGIS SET UP CONTROLLER INDICATIONS FCC NOTICE... -
Page 3: Description
Although HSP recommends the use of SX series transmitters, 303.875 MHz S1 and Megacode transmitters may also be used with the AEG-WR Wireless Receiver. You can use up to 64 unique transmitters with the AEG-WR Receiver. Each zone reported to the controller can have... -
Page 4: Installation
1.00 4.00 The receiver can report status to 16 zones on an Aegis controller. Transmitters 1-16 report to zones 17-32. If a 17th transmitter is used, the status of that transmitter is reported to zone 17; the status of the 18th transmitter is reported to zone 18, etc. -
Page 5: Operation
Place the cover on the receiver and install the antenna onto the antenna connector. Connect the receiver to the controller using 4 conductor 22 gauge or larger wire as follows: OPERATION The two operating modes of the receiver are "Run" and "Set Up". In Run mode, with the receiver connected to the controller, the Mode LED should blink once per second. - Page 6 (not ready) or that have trouble. The transmitter number flashes on the display followed by the status condition(s). LED DISPLAY INFORMATION ABOUT THE LED DISPLAY 1.10 Displays the number of the transmitter with a change in condition. Displays that the current transmitter is "NOT READY". Displays that the cover was removed from the current transmitter.
- Page 7 Mode/Advance switch is pressed. Set Up mode is exited when the Mode/Advance switch is pressed for two seconds. NOTE: When using the receiver with an Aegis system, the address must be set to "1". Next, you are prompted to enter the number of addresses. The letter "n" is shown on the left of the display and the digit for the current number of addresses is shown on the right of the display.
- Page 8 The next four items allow you to change each digit of your security code. The Set switch is used to increment the value of each digit. The Mode/Advance switch is used to enter each digit and advance to the next. Next, the programmed characteristics of each transmitter is displayed.
-
Page 9: Reset Memory
INSTALLER SETUP: ↓ 1=CTRL 2=ZONE 3=DCM From the Installer Setup menu, select the 2 (ZONE) key. If used with an Aegis, press 2 (RCVR), then ' # ' to enable the AEG-WR Wireless Receiver. ZONE EXPANSION: ↓ 0=NONE 1=H/W 2=RCVR If used with an Aegis, you must set the Number of Expansion Enclosures. -
Page 10: Controller Indications
CONTROLLER INDICATIONS When the condition of a transmitter changes state, the HAI controller will display that condition as follows: Transmitter Condition Aegis When a transmitter (zone) is violated Zone Name "NOT RDY" When a cover is removed from a transmitter Zone Name "NOT RDY"... -
Page 11: Fcc Notice
FCC NOTICE This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Verified to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. - Page 12 QUICK-REFERENCE SETUP GUIDE To Enter Set Up mode, press and hold the Mode/Advance switch for 2 seconds. DISPLAY DESCRIPTION SET SWITCH MODE/ADVANCE SWITCH Enter the first digit of the code Increments the digit (0-9) Advances to the next digit Enter the second digit of the code Increments the digit (0-9) Advances to the next digit C 0.
Need help?
Do you have a question about the AEG-WR and is the answer not in the manual?
Questions and answers