Advertisement
HuddleCamHD Serial Joystick Controller
Model Number: HC-JOY-G2
Joystick Keyboard Installation & Operation Manual
Easy pan, tilt & zoom controls for any RS-232, RS485, RS422 VISCA, Pelco-P or
Pelco-D protocol camera!
Controls pan & tilt with variable speed.
Uses 3 dimensional joystick with "twist" control for variable zoom.
Rev 1.0 8/16
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HuddleCamHD HC-JOY-G2
Summary of Contents for HuddleCamHD HC-JOY-G2
- Page 1 HuddleCamHD Serial Joystick Controller Model Number: HC-JOY-G2 Joystick Keyboard Installation & Operation Manual Easy pan, tilt & zoom controls for any RS-232, RS485, RS422 VISCA, Pelco-P or Pelco-D protocol camera! Controls pan & tilt with variable speed. Uses 3 dimensional joystick with “twist” control for variable zoom.
-
Page 2: Key Product Features
Key Product Features All Metal housing. VISCA, PELCO-D and PELCO-P protocol support. Large LCD Menu display. Key-press “BEEP” confirmation (optional – set on or off). Pan, tilt, zoom, iris and focus control. Variable speed control of pan, tilt and zoom. ... -
Page 3: Installation
In the Box Keyboard with three-axis control joystick. 5p screw terminal plug (RS422/RS485). 12VDC Power Supply. This Manual. Installation Power Supply Interface (5.5mm x 12mm center pin JEITA style jack): 12VDC / 2000mA power supply. ... - Page 4 Keyboard/Joystick Operation Basic Control Pan & Tilt Control o Joystick movement provides variable speed pan and tilt of the camera head. Zoom Control o Rotation of the joystick controls variable speed zoom of the lens. Clockwise rotation of the joystick = zoom in. ...
- Page 5 keys: “Iris+”, “Iris-” (“Man Exp” must first be enabled). o Auto Iris may be enabled by pressing the “Aut Exp” key. o Manual Iris may be enabled by pressing the “Man Exp” key. Note: Some cameras do not have an “Iris” (or manual Iris) mode. For this reason, Manual Exposure is used.
- Page 6 Pelco) Notes on using presets with VISCA: For your convenience, the HC-JOY-G2 uses the same preset numbers whether ‘set’, ‘called’ or ‘cleared’ via hand-held IR remote, VISCA, Pelco-P or Pelco-D. This is in contract to Sony’s traditional offset of -1 between IR remote commands and VISCA commands.
- Page 7 Move Joystick “left” and “right” to select the desired control protocol or baud rate (to match that of camera). Repeat for all camera IDs required. Press “Esc” to return to previous menu level. o “SET >>SYS” : Menu ...
- Page 8 “Enter” key to confirm. o LCD screen will go Black. Press “Enter” key again. o OPEN LOCK: Using “Number” keys, enter the desired password (4 numeric keys). Press “Enter” key to confirm. Keyboard/Joystick Connection Wiring and Indicators Indicators: “PW” illuminates Red when unit is powered ...
-
Page 9: Troubleshooting
For RS232, connect the DB9 port of the KB to the miniDin8 (VISCA) port of the camera with pin-out as follows: o KB Tx – Pin 3 ---------- Camera Rx - Pin 5 o KB Rx – Pin 2 ---------- Camera Tx - Pin 3 o KB Gnd –... - Page 10 A VISCA cross-over cable must be used for all camera to camera connections. These are available from HuddleCamHD in various lengths as well as from other sources. For RS485 and RS422, all connections are in parallel (e.g. all cams’...
Need help?
Do you have a question about the HC-JOY-G2 and is the answer not in the manual?
Questions and answers