ZD T7AH-2400 Instruction Manual
  1. Manuals
  2. Brands
  3. ZD Manuals
  4. Video Game Controller
  5. T7AH-2400
  6. Instruction manual

ZD T7AH-2400 Instruction Manual

Hide thumbs

Advertisement

Table of Contents

T7AH-2400
SHENZHEN XINGYAOHUAINDUSTRIALCO. , LTD
+ 86( 755) 84673906
Tel:+86(755) 84008148
Fax: + 86(755)84673903
Address:NO. 28 Wenxin Road, Xinmu Lao Village,
Pinghu Town,Longgang District, Shenzhen City,
Guangdong Province, 518111 China
Website:www.zdracing.com

Advertisement

Table of Contents
loading

Summary of Contents for ZD T7AH-2400

  • Page 1 T7AH-2400 SHENZHEN XINGYAOHUAINDUSTRIALCO. , LTD + 86( 755) 84673906 Tel:+86(755) 84008148 Fax: + 86(755)84673903 Address:NO. 28 Wenxin Road, Xinmu Lao Village, Pinghu Town,Longgang District, Shenzhen City, Guangdong Province, 518111 China Website:www.zdracing.com...

  • Page 2: Table Of Contents

    T 7AH-2400 instruction manual Catalogue Safety and attention matters 、 One Summarize ＊　To make your remote control equipment can make model correct and work Second、 Characteristics safety, please read this manual carefully，and use it strictly with the instructions in the future. Three、...

  • Page 3: Second, Characteristics

    M-LED indicator light changes from flickering into lighting. Then, T7AH-2400 is a style of RC equipments that can be used for fixed wing aircraft also can be used for helicopters model aircraft.It use the 2.4 GHz frequency-hopping...

  • Page 4: Seven、Input Method

    ◆ Control stick length adjustment The 7 TAH-2400 allows you to adjust the control stick's length. Use the 2mm Allen wrench, turn the wrench counterclockwise to loosen the crew. Then, turn the stick clockwise to shorten or counterclockwise to lengthen. After the control stick length has been adjusted to suitable height, tighten the 2mm setscrew.

  • Page 5: Input Mode And Function Selection

    Input key and scroll under the condition of input, all will make a sound to DECREASE、CLEAR, The specific function of this several LCD operation buttons confirm the correct. Add keys and Decrease keys have rapidly increasing or decreasing function as described below: (continuous pressure which will rapidly increasing or decreasing) SCROLL UP and SCROLL DOWN, the two keys used to flip menus.
  • Page 6 ◆ pressing CLEAR key. Only aircraft adjust for HELI, just have this feature setup. T7AH-2400 offers four independent pitch curves, each with up to five adjustable Press to enter REVERSE Press to select REV. or NORM points. This function allocates a separate pitch curve setting during normal, stunt 1, stunt 2 and hold modes.
  • Page 7 Adjustment of the throttle curves is similar to the pitch curve adjustment described on the preceding page. Three throttle curves are available: normal, st1 and st2. All throttle curves have five adjustable points—low, 25%, 50%, 75% and high. Flight modes are located on the 3-position flight mode switch. The throttle curve is traner flaps Antenna in the normal mode when the Flight Mode switch is in the rear position and the...

  • Page 8: System Model Function

    ACRO The INCREASE and DECREASE keys are used to change the values of the selected programming feature. T7AH-2400 features two programming modes: System Mode and Function Mode. 9.1System Mode Functions System Mode Hold while turning on transmitter to enter System Mode...
  • Page 9 MODEL 1 ◇ HELI Type Select Function The T7AH-2400 features two programming types: Airplane and Helicopter. The MODEL 2 ACRO DX7 can memorize data for up to six fixed wing aircraft and six helicopters model and the model type will automatically be stored with each model memory.
  • Page 10 ◆Pole mode The T7AH-2400 have in four different control rod "mode" (0, 1, 2, 3). Different mode ◇To Perform a DATA RESET or Reset the Integrated Timer corresponding to operation function of different control rod. Usually, set in "mode" 1.
  • Page 11 ◆Channels Distribute In addition, you have 3 choices to activate/inhibit FLAP SYSTEM: The T7AH-2400 can assign 7 channels to output in any channel, you can choose a ● System (3-position switch) different style of the channel allocation, can also customize the output channel ●...
  • Page 12 ◆Flaperon Wing Type Servo Connections Press to enter WING TYPE FUNCTION INCREASE and DECREASE key ● AILE servo port (right aileron) ● AUX1 servo port (left aileron) [WING TYPE] FLAPERON Flaperon Wing Type Servo Connections TAIL • AILE ser vo port (right aileron) •...

  • Page 13: 9.3Function Mode Flowchart

    ◆Function Mode (Page 36) Sub Trim (Page 28) Timer [ TIMER ] [SUB TRIM] UP and DOWN key INCREASE and DECREASE key MODEL 1 THRO AILE DOWN-T 00:00 ELEV RUDD SW:ADJUST 10.6V MODEL 1 Travel Adjust (Page 29) Programmable Mixing (1-6) (Page 34) 12.5ms FRAME RATE [TRAVEL ADJUST] [PROG.MIX1]...
  • Page 14 ◇To Enter the Function List Mode and selectedwith a switch. Dual rates and expos are available on the aileron, ● Turn the transmitter on. elevator and rudder channels. Changing the dual rate value not only affects the ● From the main screen, press the UP and SELECT keys simultaneously. maximum control authourity but also affects the overall sensitivity of control.
  • Page 15 ◆Reverse Switch extremes of throw. The sensitivity around center can be tailored using the Exponential function to precisely adjust control feel. The Reverse Switch function allows electronic means of reversing the servo’s throw Exponential rates can be controlled by their respective rate switches (aileron, .
  • Page 16 ◆Travel Adjust Press to adjust value The Travel Adjust function allows the precise end-point adjustments of all seven channels in each direction independently. The travel adjust range is from 0–150%. [ ELEV - FLAP MIX ] Channel available for programming are: RATE: D Press to enter TRAVEL ADJUST ●...
  • Page 17 ◇To Access the Aileron-to-Rudder Mix Function ◆ Automatic Landing Press the DOWN and SELECT keys simultaneously to access the Function Mode. When the Automatic Landing Function is active, the throttle stick will activate the In Function Mode, use the UP or DOWN key to select the AILE-RUDD MIX screen. landing system you have just set up.
  • Page 18 Press the SELECT key to highlight switch. OFFSET: Press the INCREASE or DECREASE key to select the desired switch. ◆Programmable Mixing 1–6 The T7AH-2400 offers six programmable mixes that allow stick or switch inputs to Press to enter Press to highlight Press to return control the output of two or more servos.
  • Page 19 ◆ ◇Assigning Mixing Values Timer Press the DOWN and SELECT keys simultaneously to access the Function Mode. TheT7AH-2400 features an onscreen timer with three programming options. In Function Mode, use the UP or DOWN keys to select the desired PROG. MIX screen INH: Press the SELECT key to select RATE.
  • Page 20 Press the INCREASE or DECREASE Press the INCREASE or DECREASE key to start or stop the timer key to start or stop the timer 10.6V 10.6V MODEL 1 MODEL 1 12.5ms FRAME RATE 12.5ms FRAME RATE DOWN-T DOWN-T 10:00 10:00 Press the CLEAR key to reset the timer Press the CLEAR key to reset the timer ◇To Access the Timing Function...
  • Page 21 ◆Throttle Hold/Stunt Mode Lift wing ratio Aileron ratio When the T7AH-2400 is operated in the helicopter mode, there is a warning system that is employed to avoid hot starts (accidental high throttle startups). If the power Lift direction Throttle...
  • Page 22 > GYRO GEAR The T7AH-2400 features a memory function that stores the programmed data for up to 6 models. Any combination of up to 6 airplanes and/or helicopters can be Type Select (Page 44) stored in memory. A model name feature with up to eight characters allows each Throttle Recovery (Page 46) model to be easily identified.
  • Page 23 Press the INCREASE or DECREASE key to select the desired character. types.To accept the new model type by pressing the CLEAR key. ◆Type Select Function The T7AH-2400 features two programming types: Airplane and Helicopter. The ◆Model Reset/Integrated Timer T7AH-2400 can memorize data for up to 6 models individually.
  • Page 24 ◆Pole mode ● Press the UP key until the MODEL RESET function appears on screen. The T7AH-2400 have in four different control rod "mode" (0, 1, 2, 3). Different ● Press the SELECT key until INTEg-T is highlighted. mode corresponding to operation function of different control rod. Usually, set in ●...
  • Page 25 Press the INCREASE and DECREASE keys to change the pole mode. positions are available. Sub trim and travel adjust is used to set the center and The T7AH-2400 can assign 7 channels to output in any channel, you can choose a end points for each switch position.
  • Page 26 that are frequently used. GYRO: Gyro is selected under gear if you wish to have the Gyro Sensing (see Page 96 to 10.2 flow chart of function mode: gain more detail) operate using the gear channel. the following programming of function mode, more common usage inclusive. AUX2: [D/R &...

  • Page 27: Function Mode Function

    UP and DOWN key INCREASE and DECREASE key UP and DOWN key INCREASE and DECREASE key [D/R & EXP] POS-0 [FUNCTION LIST] AILE PI CURV ST2 PROG.MIX3 TIMER REVO. MIX MONITOR 100% GYRO SENS PROG.MIX1 PROG.MIX2 Press to enterFunction Mode ◇To Enter the Function Mode SELECT key CLEAR key...
  • Page 28 St1, ST2, and Hold.) When an auto dual rate flight mode is inhibited, the dual rate The Exponential function allows two exponential rates to be programmed and is defaulted to the correlating switch and dual rate switch positions. selected with a switch. Exponential is available on the aileron, elevator and rudder Press to enter channels.
  • Page 29 ● THRO: Throttle ● AILE: Aileron ● ELEV: Elevator ● RUDD: Rudder ● ELEV: Elevator ● GEAR: Gyro Gain ● PIT: Pitch (AUX1) Gyro Gain ● RUDD: Rudder ● GEAR: Retractable Landing Gear ◆Sub Trim ● PIT.: Pitch The Sub-Trim function allows you to electronically adjust the centering of each ●...
  • Page 30 ◆Throttle Curve value to default on the transmitter The T7AH-2400 offers three (3) separate throttle curves with five (5) adjustable ◇Accessing the Swashplate Mix Function points per curve. This function allows you to adust the throttle curve to optimize Press the DOWN and SELECT keys simultaneously to access the Function Mode.
  • Page 31 ◆Setting Up Revolution Mixing The T7AH-2400 offers four (4) independent pitch curves: Normal, Stunt 1, Stunt 2 First, adjust the helicopter so that it will hover in a neutral position with the tail rotor and Hold.
  • Page 32 THRO ◆Programmable Mixing 1–3 RATE: In helicopter mode the T7AH-2400 offers three (3) programmable mixes that allow OFFSET stick or switch inputs to control the output of two or more servos. This function allows mixing any one channel to any other channel or the ability to mix a channel to itself.
  • Page 33 DOWN-T 10:00 Press the INCREASE or DECREASE key to select the desired offset value. ◆Timer T7AH-2400 provides a screen show timer.with three programmable Settings INH：Shielding-in this mode timer is closed Press the CLEAR key to reset the timer DOWN-T: ◇Access to the timer function Countdown timer-decreasing order of default timer which allowed 10 seconds of Press the DOWN and SELECT buttons simultaneously to enter the system mode.
  • Page 34 Press to enter SERVO MONITOR system could last . ●Before the first flying ,check the Underside distance,please have a look at the daily THRO flight check chapter. AILE ●Before flying ,check all the appearance control . ELEV RUDD ●Don't fly in the public, parking lot or other personal property losses. GEAR ●Don't fly in the bad weather.Very poor visibility can lead to problems or the plane PIT.

Table of Contents