Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for VOLKTEK men-9632
- Page 1 MEN-9632 Installation Guide www.volktek.com Copyright © 2014 Volktek Corporation...
- Page 2 Installation Guide for MEN-9632 Copyright © 2014 Volktek Corporation All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photo copying, recording or otherwise, without the prior written...
-
Page 3: Table Of Contents
Installation Guide for MEN-9632 Contents Preface ..................... 4 Related Documentation ................4 Hardware Installation ................5 1.1. Unpacking ....................5 1.2. Product Layout ..................6 1.3. Connecting AC/DC/Battery Power .............. 7 1.4. Installing SFP modules and Fiber cables ............. 8 1.5. -
Page 4: Preface
Installation Guide for MEN-9632 Preface This manual is the installation guide for MEN-9632 and contains the following sections: Hardware Installation • Unpacking Product Layout • • Connecting AC/DC/Battery power • Installing SFP modules and Fiber cable LEDs • Software Configuration ... -
Page 5: Hardware Installation
1. Hardware Installation 1.1. Unpacking Open the package and carefully unpack the switch The box should contain following items*: One MEN-9632 – 24-slot 100FX/GbE SFP, 4-Gigabit Combo ports, L3 Managed switch One Console Cable – DB9 (RS232) One AC power cord ... -
Page 6: Product Layout
The front panel of the MEN-9632 consists of 24-100FX/GbE SFP slots, 4-Gigabit Combo ports, AC power socket, LEDs and Console port. Console Port LEDs A/C Power Rear View The rear view panel of the MEN-9632 consists of 12V Battery connector and/or 48V DC input Battery connector 48V DC Input... -
Page 7: Connecting Ac/Dc/Battery Power
Hardware Installation 1.3. Connecting AC/DC/Battery Power The MEN-9632 supports 240V AC and 12V battery or 48V DC power supplies. LED indicating AC Power input Connect battery to switch and check polarity • Connect Positive (+) to Positive (+) and Negative (-) to Negative (-) •... -
Page 8: Installing Sfp Modules And Fiber Cables
Hardware Installation 1.4. Installing SFP modules and Fiber cables Steps to install SFP modules: • Slide the SFP module into the selected SFP slot (Make sure SFP module is aligned correctly with the SFP slot) Insert and slide the module into the SFP slot until it clicks into place •... -
Page 9: Leds
Hardware Installation • To pull the connector out, press the release clip and pull the connector from SFP module 1.5. LEDs The LEDs on the MEN-9632 are as below:... - Page 10 Hardware Installation The LEDs on the MEN-9632 indicate the following: Unit LEDs Condition Status On (Green) Switch is ready and running Ok POST Flashing (Green) Switch is booting Switch is not ready or failed On (Green) Power On PWR1 Power Off or fail...
-
Page 11: Software Configuration
Password: admin Steps to access the switch through web-based management interface: Set the IP address of your computer to 192.168.0.XXX • • Connect MEN-9632 to your computer • Open your computer’s web browser Type http://192.168.0.254 in the address box to access the web •... -
Page 12: Console
Software Configuration 2.1.2. Console Steps to access the switch through console port: • Insert male pin of the console cable in Console port of the MEN-9632 Connect DB-9 pin to your computer serial port •... - Page 13 Software Configuration Console login through putty: After connecting console cable to MEN-9632 console port and your computer’s serial port, Go to Device manager • • Scroll to ‘Ports’ USB Serial Port (COM#) Make a note of COM# •...
- Page 14 Software Configuration Console Login through Hyper Terminal: Note: HyperTerminal is not an in-built feature in Windows Vista, 7 and 8. You can copy it from Windows XP. Use the following settings...
-
Page 15: Configuration Backup/Restore
Software Configuration 2.2. Configuration Backup/Restore Steps to backup and restore configuration file: • Run TFTP server • Set TFTP server IP and Gateway (e.g. IP: 192.168.0.200 and Gateway: 255.255.255.0) • Specify directory path as shown in figure below • Use the following command to backup (upload) configuration file (e.g. -
Page 16: Reset To Default Configuration
Software Configuration 2.3. Reset to Default Configuration • Use the following command to reset the switch to its factory default configuration settings Factory default configuration 2.4. Firmware Upgrade Steps to upgrade the firmware of the switch: Place firmware (FW) in root directory of the TFTP server •... -
Page 17: Support
Installation Guide for MEN-9632 Support For any assistance with this product, please visit Support section of www.volktek.com website. Also, you can contact us by email: support@volktek.com...
Need help?
Do you have a question about the men-9632 and is the answer not in the manual?
Questions and answers