Wiring Instructions - Attwood 3100 Installation Instructions

Figure 3a
(Optional Mount with Snap Base)
(For ease of installation without disassembly of light.)
Product
1/4" Snap Base
1" Snap Base
Gasket
(Installs between Light Assy and Snap Base)
SAVE THESE INSTRUCTIONS
ATTWOOD LIMITED WARRANTY Attwood Corporation, 1016 North
Monroe, Lowell, Michigan 49331 ("Attwood") warrants to the original
consumer purchaser that Attwood brand products will be free from defects
in materials and workmanship under normal use and service for one year
from the date of original consumer purchases.
This limited warranty is not applicable if the product has been damaged by
accident, improper installation, unreasonable or improper use, lack of proper
maintenance, unauthorized repairs or modifications, normal wear and tear,
or other causes not arising out of defects in materials or workmanship.
Attwood products are warranted for use on pleasure boats. Any other use—
including but not limited to commercial, racing, or non-marine use—are not
covered under this warranty. Attwood's obligation under this warranty is
limited to repair of the product at Attwood's plant or replacement of the
products at Attwood's option without expense to the original consumer
purchaser. Any expenses involved in the removal, reinstallation or transpor-
tation of the product are not covered by this warranty.
The product must be returned to Attwood's plant at the address above,
postage pre-paid, and insured with proof of original purchase including date.
If Attwood is unable to replace the product and repair is not commercially
practical or cannot be timely made, or if the original consumer purchaser is
willing to accept a refund in lieu of repair or replacement, Attwood may
refund the purchase price, less an amount for depreciation. The acceptance
Light Assembly
Mounting Screws
(Not Supplied)
Connecting Posts
Snap Base 1/4" or 1"
(6mm or 25mm)
Boat Centerline
Forward
Part Number
3300 (Black)
3301 (White)
3302 (Gray)
3304 (Cream)
3310 (Black)
3311 (White)
3312 (Gray)
3314 (Cream)
912010

WIRING INSTRUCTIONS

The power source must be 12-volt DC ONLY. Use marine
grade wire connectors only. Protect all connections with suitable
materials.
NOTE: Failure to make proper connections and fuse the light
properly will void the product warranty.
1. Connect one terminal to the negative ( - ) post of the 12-volt
battery. Connect the other terminal to the positive ( + ) lead
through a 2-amp fuse and suitable dash-mounted switch. (See
Figure 4.)
Figure 4
Switch
2-Amp
Fuse
•
•
2. Test lights for proper operation from dash-mounted control
switch.
MAINTENANCE
Replace bulb, when necessary, with standard 8-watt automotive
festoon type (Attwood #9230-7).
by Attwood of any product returned or any refund provided by Attwood shall
not be deemed an admission that the product is defective or in violation of
any warranty. Products that are replaced or for which a refund is issued
become the property of Attwood.
THIS WARRANTY IS ATTWOOD'S ONLY EXPRESSED WARRANTY OF
THESE PRODUCTS. NO IMPLIED WARRANTY INCLUDING, WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, SHALL BE EXTENDED
BEYOND THE WARRANTY PERIOD STATED ABOVE FOR EACH
PRODUCT. ATTWOOD SHALL NOT BE LIABLE FOR ANY DAMAGES,
FOR LOSS OF USE OF THIS PRODUCT, NOR FOR ANY OTHER
INCIDENTAL OR CONSEQUENTIAL DAMAGES, COSTS, OR EXPENSES.
Some states do not allow limitations on how long an implied warranty lasts
or the exclusion or limitation of incidental or consequential damages, so the
above limitations and exclusions may not apply to you. This warranty gives
you specific legal rights, and you may have other rights which vary from
state to state.
© 2003 Attwood Corporation
1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com