Subscribe to Our Youtube Channel
Related Manuals for Tritech Super SeaSpy
Summary of Contents for Tritech Super SeaSpy
- Page 1 Super SeaSpy Camera Super SeaSpy Camera Product Manual 0514-SOM-00001, Issue: 02 0514-SOM-00001, Issue: 02 © Tritech International Ltd.
- Page 2 The copyright in this document is the property of Tritech International Ltd. The document is supplied by Tritech International Ltd on the understanding that it may not be copied, used, or disclosed to others except as authorised in writing by Tritech International Ltd.
-
Page 3: Table Of Contents
Help & Support .................... 4 Warning Symbols ..................5 1. Introduction ....................6 2. Specification .................... 8 2.1. Super SeaSpy Dimensions ............8 2.2. Optical ................... 8 2.3. Illumination ..................8 2.4. Electrical and Communication ............9 2.5. Physical ..................9 3. -
Page 4: Help & Support
Prior to contacting Tritech International Ltd please ensure that the following is available: 1. The Serial Numbers of the product and any Tritech International Ltd equipment connected directly or indirectly to it. 2. Software or firmware revision numbers. 3. A clear fault description. -
Page 5: Warning Symbols
Super SeaSpy Camera Warning Symbols Throughout this manual the following symbols may be used where applicable to denote any particular hazards or areas which should be given special attention: Note This symbol highlights anything which would be of particular interest to the reader or provides extra information outside of the current topic. -
Page 6: Introduction
The light can also be adjusted manually if required. To prevent damage from warm environments the LEDs also incorporate an automatic thermal cut-out. The Super SeaSpy has an internal focus adjustment which allows the focal range to be factory set at values between 50mm and infinity. The camera power supply provides excellent protection for the efficient operation of the camera module. - Page 7 Introduction Super SeaSpy Camera • On-line industrial machinery inspection • Restricted access areas 0514-SOM-00001, Issue: 02 © Tritech International Ltd.
-
Page 8: Specification
Super SeaSpy Camera 2. Specification 2.1. Super SeaSpy Dimensions 99.0 53.0 Not to scale, dimensions in mm. 2.2. Optical NTSC Vertical resolution 550 lines 470 lines Scanning system 625 lines at 50 Hz 525 lines at 60 Hz CCD module 1/3"... -
Page 9: Electrical And Communication
Specification Super SeaSpy Camera 2.4. Electrical and Communication Power requirement 12 to 48V DC (drawing 4.8W at 24V) Standard connector Tritech 6-pin connector Optional connector Schilling SeaNet 2.5. Physical Weight in air 0.65kg Weight in water 0.45kg Depth rating 4000m Temperature -10 to 35°C operating (-20 to 50°C in storage) -
Page 10: Installing The Seaspy
To connect the camera to a computer for testing or operation it will be necessary to construct an appropriate test cable. The pin-out diagram for units fitted with the Tritech 6 pin standard water block is shown in the specification section, for any other connectors it will be necessary to refer to the documentation that was provided with the camera to establish the correct wiring scheme. - Page 11 Installing the SeaSpy Super SeaSpy Camera Waterblock Pin-out Diagram Function Lights +/- not connected +DC Power -DC Power Video Out Tritech Waterblock not connected Cable Pin-out Diagram Colour Yellow Blue Black Green SCREEN Tritech Cable 0514-SOM-00001, Issue: 02 © Tritech International Ltd.
-
Page 12: Using The Seaspy
The Super SeaSpy is a fixed-focus camera and the focal length is factory set. The focus can be adjusted by the user, or by returning the unit to Tritech International Ltd for servicing. The length can be specified from 50mm to infinity. -
Page 13: Dynamic Light Control (Dlc)
4.2.2. Dynamic Light Control (DLC) Upon initial power up the Super Seaspy camera will start up in Dynamic Light Control (DLC)mode. This means that the ring LED’s will react automatically to any changes in the reflectivity of the work surface or scenery ambient light conditions: - In darker areas the ring LED’s will brighten and the reverse in... -
Page 14: Maintenance
Tritech International Ltd for more details and advice. 5.2. Dis-assembly and Re-assembly procedures It may be necessary to open the Super SeaSpy in order to inspect the 'O' ring surfaces, adjust the video amplifier, or to adjust the focus of the unit. - Page 15 Maintenance Super SeaSpy Camera 3. Using a large nylon washer to protect the body, inject air inside the body to a pressure of 1 bar max. The acrylic port will be dislodged by this light pressure and removed easily Caution...
-
Page 16: Internal Layout And Configuration
Super SeaSpy Camera 6. Internal Layout and Configuration 6.1. General layout 6.2. LED light ring 0514-SOM-00001, Issue: 02 © Tritech International Ltd. -
Page 17: Electronic Light Control
Internal Layout and Configuration Super SeaSpy Camera 6.3. Electronic light control FOR +\- SINGLE WIRE (Bi-polar Control) - DEFAULT SETTING Link solder pads 1 & 2 together +/- LIGHT is supplied with +5 to +24 volts, LED’s Brighten +/- LIGHT is supplied with -5 to -24 volts, LED’s Dim +/- LIGHT is left un-connected, LED’s remain constant... -
Page 18: Video Output
Internal Layout and Configuration Super SeaSpy Camera 6.4. Video output TO ENABLE VIDEO OUTPUT WITHOUT AMPLIFICATION (Default Setting) Link solder pads 1 & 2 together - Amplification & video filter are OFF TO ENABLE VIDEO OUTPUT WITH AMPLIFICATION Link solder pads 2 & 3 together - Amplification &... -
Page 19: Video Amplifier
Internal Layout and Configuration Super SeaSpy Camera 6.5. Video amplifier NO VIDEO AMPLIFICATION (Default Setting) No solder links on S22 S21 must have solder pads 1 & 2 linked together Buffer with gain of one: OFF Set amplifier with high-frequency boost: OFF VIDEO AMPLIFICATION (Medium cable length) Link solder pads 1 &... -
Page 20: Fuse Information
Internal Layout and Configuration Super SeaSpy Camera VR21 (Gain trimmer) allows a manual adjustment of video signal amplitude via variable resistor, up to a maximum of (2Vp-p). To have any effect S22 must have pads 2 & 3 linked and S21 must have pads 2 & 3 linked. -
Page 21: Wiring Information
Internal Layout and Configuration Super SeaSpy Camera 6.7. Wiring information LED & Sensor connections: 1 to 4 Camera Module connections: 1 to 6 LED & SENSOR CONNECTIONS Pin 1 +10V to LED board Pin 2 Light sensor + Pin 3... -
Page 22: Troubleshooting
Super SeaSpy Camera 7. Troubleshooting Symptom Likely cause Remedy Image not in focus Focal length incorrect for Check original specification application when purchased If focal length specified matches current application (i.e. usage has not changed since initial purchase) there may be a... -
Page 23: Glossary
Super SeaSpy Camera Glossary Direct Current Dynamic Light Control - an automated control system for the LED light ring within the Super SeaSpy camera. Light Emitting Diode NTSC National Television System Committee - an analogue television standard used in most of North America.
Need help?
Do you have a question about the Super SeaSpy and is the answer not in the manual?
Questions and answers