Black & Decker GH1000 Instruction Manual page 6

4. Place spool and line into spool housing with lines "parked" in slots provided as shown in
Figure 10.
5. Insert the line ends through the holes in the spool hub. Pull slack line through until it
pulls out of the holding slots as shown in Figure 11.
6. Press the spool down GENTLY and rotate it until you feel it drop into place and then
push to snap into place. (When in place, the spool will turn a few degrees left and right
freely). Take care to keep the line from becoming trapped under the spool.
7. Snap the hub cap back on as shown in Figure 12, by depressing lugs and pressing into
spool housing. NOTE: Make sure that cover is fully positioned, listen for two audible
clicks to ensure both lugs are correctly located. Power the tool on. In a few seconds or
less you'll hear the nylon line being cut automatically to the proper length.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts.
ACCESSORIES
Use Black & Decker replacement spool Model No. DF-080.
Reload nylon line (either bulk or prewound replacement spool) as shown in this manual.
• USE ONLY .080" (2mm) DIAMETER NYLON MONOFILAMENT LINE. Do not use
serrated or heavier gauge line, as they will overload the motor and cause overheating.
The unit only functions properly with 0.080" (2mm) diameter nylon monofilament line.
This line is available at your local dealer or authorized service center.
WARNING: The use of any accessory not recommended by Black & Decker for use with
this tool could be hazardous.
SERVICE INFORMATION
Black & Decker offers a full network of company-owned and authorized service locations.
All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you.
ESPECIFICACIONES/ESPECIFICAÇÕES/SPECIFICATIONS
GH1000 AR
Voltaje/Voltagem/Votlage 220V
Frecuencia/Frequency 50Hz
Potencia/Power 900W
RPM 7,200
Solamente para propósito de Argentina: Solamente para propósitos de Colombia
Importado por: Black & Decker Argentina S.A. Importado por: Black & Decker de Colombia, S.A.
Pacheco Trade Center Carrera 85D # 51-65, Bodega 23
Colectora Este de Ruta Panamericana Complejo Logístico San Cayetano
Km. 32.0 El Talar de Pacheco Bogotá - Colombia
Partido de Tigre Tel.: 744-7100
Buenos Aires (B1618FBQ)
República de Argentina Solamente para propósito de Chile:
No. de Importador: 1146/66 Importado por: Black & Decker de Chile, S.A.
Tel.: (011) 4726-4400 Av. Pdte. Eduardo Frei M. 6001-67 Conchalí
Santiago de Chile
Imported by/Importado por: Tel.: (56-2) 687 1700
Black & Decker do Brasil Ltda.
Rod. BR 050, s/n°- Km 167 impreso en China
Dist. Industrial II impresso em China
Uberaba ˆ MG ˆ Cep: 38064-750 Printed in China
CNPJ: 53.296.273/0001-91
Insc. Est.: 701.948.711.00-98 90596406
S.A.C.: 0800-703-4644 27/02/13
B2 B3 B2C
220V 120V 220V
60Hz 60Hz 50Hz
900W 900W 900W
7,200 7,200 7,200
Solamente para propósito de México:
Importado por: Black & Decker S.A. de C.V.
Avenida Antonio Dovali Jaime
# 70 Torre B Piso 9
Colonia La Fé, Santa Fé
Delegación Álvaro Obregón,
México D.F. 01210
Tel. (52) 555-326-7100
R.F.C.: BDE810626-1W7
Black & Decker del Perú S.A.
Av. Enrique Meiggs 227.
Pque. Industrial - Callao
Tel.: (511) 614-4242
RUC 20266596805
BR
127V
60Hz
900W
7,200