Summary of Contents for Manson Engineering Industrial SBC-6108
-
Page 1: Table Of Contents
PV Charge Controller SBC-6108 / 6112 / 6120 User's Manual Table of Contents Precautions and Specifications 1. Introduction 2. Control and Indicator 3. Installation and Indication 3.1 Connection 3.2 LED Indicator 3.3 Charging LED Indicator 3.4 The Dip Switch 3.4.1 Bulk Charge Voltage Setting for Sealed and Wet-type Lead Acid Battery 3.4.2 Select the Auto-Equalization charging and Night-Light Mode... -
Page 2: Precautions And Specifications
Precautions 1. Before using the charge/load controller, read all the instructions and cautionary markings on the charge/load controller, the batteries and the photovoltaic panels. 2. Do not attempt to repair the controller. Incorrect re-assembly may result in a risk of electric shock or fire. -
Page 3: Introduction
1. Introduction The SBC-6108/6112/6120 PV Charge Controller is designed for use with all types of 12V photovoltaic(PV) panels/systems and different types of 12V batteries, such as wet or sealed lead acid, lead calcium, lead antimony battery. Numerous features are provided to maximize the performance of the system: ●... -
Page 4: Installation And Indication
This controller has Electronic Blocking feature, therefore, it is not necessary to connect a diode between the PV module and the Controller. The recommended wire size is #12AWG(SBC-6108/6112) / #10AWG(SBC-6120). It is recommended that the PV Charge Controller should be installed in a dry, sheltered location away from sources of high temperature and moisture. -
Page 5: Charging Led Indicator
3.3 Charging LED Indicator It shows 3 charging modes – Bulk, Absorption and Float Charge. Charging LED Indicator Charging Status Fast Flashing Green Bulk Charge Slow Flashing Green Absorb Charge Constant Green Float Charge LED off No Charging Table 2 Charging LED Indicator 3.4 The Dip Switch Open the side door, you can see the dipswitch The dip switch are used to select the AUTO/MANUAL equalization charging, night-light... -
Page 6: Pv Charge Control Mode
Use the dip switch to select equalization charging and night-light mode as below: AUTO Night-Light Mode Dip Switch Settings Equalization Charging* Dip switch 1 – OFF Factory Dip switch 2 – ON Preset Dip switch 3 - OFF Dip switch 1 – ON Dip switch 2 –... -
Page 7: Equalization Charging Mode (Automatic Or Manual)
The three stages charging method works well with the chemical reaction that occurs as a battery is being charged. When a battery is more discharged, a regulated maximum current can be applied, since there is a lot of material available for the reactions to occur. As the battery refills, less and less chemical material is available for the reaction. - Page 8 After activating, when the PV panel voltage is lower than 3.5V for 10 minute, the Controller will turn on the light for a preset period of time according to the option selected. When the PV panel voltage is higher than 3.5V for 10minute, the Controller will turn off the light.
-
Page 9: Temperature Sensor (Optional)
Each of the 10 night-light mode options has a unique number of flashes. These are as follows: Switch Setting # of Flashes 2 Hours On 4 Hours On 6 Hours On 8 Hours On 10 Hours On 3 / OFF / 1 4 / OFF / 2 6 / OFF / 2 Dusk to Dawn... - Page 10 Activate the feature Please follow the steps below: 1. Open the case of the controller, there should be a small control board near the Remote Signal Terminal as shown in figure 5. Figure. 6 2. On the small control board, there is a sky blue color dip switch.
Need help?
Do you have a question about the SBC-6108 and is the answer not in the manual?
Questions and answers