Advertisement
Available languages
Available languages
MOUNTING THE HOUSING
NOTE: The mounting brackets and hanger bars included with the
unit will not be used for installation in existing construction.
1. Remove grille screw, motor bracket assembly and outlet box
from the unit.
2. Remove tape from louvers and be certain both damper sections
operate freely.
3. Position housing into the cutout. Feed house wiring through the
outlet box opening.
NOTE: The housing must be positioned so that the joist or
header will not interfere with installation of the outlet box.
4. Using screws or nails, secure the housing to the joist/header(s)
through the keyhole slots provided in sides of housing. Be certain
plaster flange is against finished ceiling.
5. Connect 7" ductwork.
MAKING THE CONNECTIONS
1. Remove one of the two side knockouts from the outlet box.
Install 7/8" box connector (not supplied). Insert house wiring
approximately six inches through box connector and tighten
screws to secure. Using wire nuts (not supplied) connect house
wiring to receptacle in outlet box cover: black to black and white
to white. Secure ground (bare wire) under green ground screw in
outlet box.
2. Install outlet box in opening in housing and secure with two short
screws provided. Feed all wiring into outlet box and secure cover.
INSTALLATION IN NEW CONSTRUCTION
MOUNTING THE HOUSING
1. Remove grille screw and motor bracket assembly from unit.
NOTE: These pieces can be set aside until the finished ceiling
is in place.
2. Insert outlet box into housing and secure with two short screws
(supplied).
3. Remove appropriate knockout from outlet box and install a box
connector.
4. Insert mounting brackets into slots in fan housing.
5. Remove tape from louvers and be certain both damper sections
operate freely.
6. Place hanger bars into mounting brackets. Nail hanger bars to
joist, adjusting slightly so housing will be held firmly in place.
Raise or lower mounting brackets to adjust housing so plaster
flange will fit flush to finished ceiling.
7. Connect 7" ductwork.
MAKING THE CONNECTIONS
IMPORTANT: Be certain all wiring complies with electrical codes
and the unit is properly grounded. Disconnect power at circuit
breaker.
1. Run house wiring (with ground) THROUGH BOX CONNECTOR.
Using wire nuts (not supplied) connect house wiring to fan: black to
black, white to white. Connect ground wire to green ground screw.
2. Secure junction box cover.
COMPLETING THE INSTALLATION
1. Mount Motor/Blade assembly into housing with plug towards
receptacle. Hook keyhole slots in motor mounting bracket over
two (2) mounting screws. Tighten screws and plug motor into
receptacle. Be certain fan blade spins freely.
2. Place grille over unit and secure with supplied thumbscrew.
3. Re-connect power and check for proper operation.
NOTE: An optional washable, permanent filter may be used with
this fan. If desired, order NuTone Model 834 separately.
MAINTENANCE
• Grille should be cleaned with a mild soap and water solution.
• If the optional filter is used, it may be removed and cleaned in
sudsy water. Rinse thoroughly and allow to dry completely before
placing into Ceiling Fan. For best results, clean filter frequently.
SERVICE PARTS
MODEL 8210 SERIES
2
4
6
3
9
11
13
Key No.
Part No.
1
1024B000
2
16754000
3
16755000
4
16756000
5
11320000
6
99270982
7
10247000
8
68293000
9
34417000
10
17674000
11
16665000
12
S99111332
13
97017716
One Year Limited Warranty
WARRANTY OWNER: Broan-NuTone warrants to the original consumer purchaser of its products that such
products will be free from defects in materials or workmanship for a period of one (1) year from the date of
original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
During this one year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or
part which is found to be defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO
FLUORESCENT LAMP STARTERS OR TUBES, FILTERS, DUCT, ROOF CAPS, WALL CAPS AND OTHER
ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any
products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair
(other than by Broan-NuTone), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one year period as specified for the express warranty.
Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply
to you.
BROAN-NUTONE'S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE'S OPTION, SHALL
BE THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE
SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF
OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This
warranty supersedes all prior warranties.
WARRANTY SERVICE: To qualify for warranty service, you must (a) notify Broan-NuTone at the address
or telephone number below, (b) give the model number and part identification and (c) describe the
nature of any defect in the product or part. At the time of requesting warranty service, you must present
evidence of the original purchase date.
Date of Installation
Builder or Installer
Model No. and Product Description
IF YOU NEED ASSISTANCE OR SERVICE - CONTACT:
Broan-NuTone LLC Hartford, Wisconsin www.nutone.com 888-336-3948
Broan-NuTone Canada Mississauga, Ontario www.nutone.ca 877-896-1119
5
7
1
8
10
12
Description
Hanger Bar and Mounting Bracket Kit
Damper Half (2 required)
Hinge Rod
Tinnerman Nut
Outlet Box
Plug Receptacle
Outlet Box Cover Assembly (includes Key No. 6)
Fan Blade
Motor
Motor Bracket Assembly
Power Unit Assembly (includes Key Nos. 8, 9, 10)
Grille
Grille Knob and Stud Kit
Rev. 08/2007
99044128C
Advertisement
