Related Manuals for Ryobi RA-NS8016-S
Summary of Contents for Ryobi RA-NS8016-S
- Page 1 RA-NS8016-S AIRWAVE AIR StAplER OpERAtOR'S MANUAl ORIgINAl INStRUctIONS Important! It is essential you read the instructions in this manual before starting and operating this machine. Subject to technical modifications.
- Page 2 DEScRIptION 1. Nitto style coupler 2. Air supply 3. Magazine 4. Magazine lock lever 5. Staples 6. Trigger lock 7. Trigger Fig. 3 8. Muzzle 9. Flat blade screwdriver Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5...
- Page 3 Fig. 7 Fig. 6 Quick Quick connector connector Lubricator Filter Tool compressor Cut-off valve Quick Quick coupler coupler Regulator Air hose (0-8.5 bar) Fig. 8...
-
Page 4: General Safety Rules
comfortable posture while maintaining a secure footing gENERAl SAFEty RUlES and avoiding awkward or off-balanced postures. The operator should change posture during extended ■ For multiple hazards, read and understand the safety tasks, which can help avoid discomfort and fatigue. instructions before installing, operating, repairing, maintaining, changing accessories on, or working ■... -
Page 5: Additional Safety Instructions For Pneumatic Power Tools
INFORMAtION ON MEchANIcAl IMpAct(VIbRAtION) ■ Repairs shall be carried out only by the manufacturer's authorized agents or by other experts, having due The characteristic vibration values for the fastener driving regard to the information given in the operating tool have been determined in accordance with ISO 8662- instructions. -
Page 6: Residual Risks
trigger using finger pressure. flying objects. In addition, fastener driving tool is fitted with a safety yoke which enables the driving operation to be carried SyMbOlS out only after the muzzle of the tool is pressed against a work piece, These tools are marked with an inverted triangle behind the serial number and are not Safety alert... -
Page 7: Intended Use
ASSEMbly Tool weight 0.92 kg (no staples) UNpAckINg NOISE AND VIbRAtION This product has been shipped completely assembled. Noise according to EN 12549:1999 and EN ISO 4871 ■ Carefully remove the tool and any accessories from the box. Make sure that all items listed in the packing A-weighted sound L PA =77.4 dB(A), K PA =2.5 dB list are included. -
Page 8: Preparing The Tool For Use
WARNINg WARNINg Do not allow familiarity with tools to make you careless. Ensure that the pressure supplied by the compressed Remember that a careless fraction of a second is air system does not exceed the maximum allowable sufficient to inflict severe injury. pressure of the fastener driving tool. -
Page 9: Setting The Air Pressure
lOADINg thE tOOl WIth FAStENERS DRIVINg A FAStENER See figure 3 - 4. See figure 5. Avoid triggering the fastener driving tool if the magazine WARNINg is empty. Any defective or improperly functioning fastener driving tool Only those fasteners specified under Specifications must immediately be disconnected from the compressed may be used. -
Page 10: General Maintenance
2. Less noise will be produced, MAINtENANcE 3. A reduction in fastener driving tool wear will be achieved. WARNINg The amount of air pressure required will depend on the size of the fastener and the workpiece material. When servicing use only identical replacement parts. Begin testing the depth of drive by driving a test fastener Use of any other parts may create a hazard or cause into the same type of workpiece material used for the... - Page 11 AIR SUpply pRESSURE AND VOlUME If it becomes necessary to store the product for an extended period of time (overnight, weekend, etc.), it should receive Air volume is as important as air pressure. The air volume a generous amount of lubrication at that time. Actuate the supplied to the tool may be inadequate because of tool 10 - 15 times without fasteners loaded to ensure oil undersize fittings and hoses, or from the effects of dirt and...
-
Page 12: Troubleshooting
tROUblEShOOtINg pROblEM cAUSE pOSSIblE SOlUtION Loose screws. Tighten screws. Air leak near the top of the tool or in the trigger area. Worn or damaged O-rings or seals. Install overhaul kit. Loose screws. Tighten screws. Air leak near the bottom of the tool. -
Page 13: Parts List
pARtS lISt Description Description Description Description Bolt M5 x 20 Gun body Nail guide groove Release handle assembly Exhaust cap Rubber washer Driver guide Nut M5 Spring Rectangle washer Washer Rubber Rectangle washer Valve pocket Step pin O-ring 35.5 x 2.3 Cylinder cover Spring Trigger... - Page 14 techtronic Industries (Australia) pty. ltd. Level 1, 660 Doncaster Road Doncaster, VIC 3108, Australia techtronic Industries New zealand ltd. 18-26 Amelia Earhart Avenue Mangere, Auckland 2022, New Zealand...