Table of Contents
Advertisement
Available languages
Available languages
Changing the selections after
programme has started
To change your settings after the program has
started, you have to switch the machine to Pause
mode first.
Even if you select a new program by changing
C
the position of the Programme Selection knob
while the machine is running or in Pause mode,
the programme selected first will continue. You
must cancel the current programme to change
the washing programme. See "Canceling the
programme".
Changing the auxiliary function, speed and
temperature
Depending on the step the programme has reached,
you can cancel or activate the auxiliary functions;
see, "Auxiliary function selection".
You can also change the speed and temperature
settings; see, "Spin speed selection" and
"Temperature selection".
Adding or taking out laundry
Press Start / Pause / Cancel button to switch the
machine to pause mode. Wait until the Loading Door
can be opened.
If the Loading Door light does not turn
C
on in 1-2 minutes, it means that the water level in
the machine is not suitable and laundry cannot be
added. You can resume the programme by pressing
Start / Pause / Cancel button. Open the Loading
Door and add or take out the laundry. Close the
Loading Door. Make changes in auxiliary functions,
temperature and speed settings if necessary. Press
Start / Pause / Cancel button to start the machine.
Canceling the programme
Press and hold Start / Pause / Cancel button for 3
seconds to cancel the current programme. At the
end of this period, machine can drain the water inside
it or can take in and drain water up to 3 times to cool
down the laundry. Washing and End lights turn on.
Once draining is complete, Start / Pause / Cancel
and Washing lights turn off, and Loading Door light
starts flashing.
When the Loading Door is openable, Loading Door
light turns on and remains lit. In this case, you can
select and start the new programme.
End of programme
End light in the programme follow-up indicator will
light up once the programme comes to an end.
Press On / Off button to switch off the machine. Take
out your laundry and close the loading door. Your
machine is ready for the next washing cycle.
5 Maintenance and cleaning
Service life of the product extends and frequently
faced problems decrease if cleaned at regular
intervals.
Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every
4-5 washing cycles) as shown below in order to
prevent accumulation of powder detergent in time.
Press the dotted point on the siphon in the softener
compartment and pull towards you until the
compartment is removed from the machine.
If more than normal amount of water and
C
softener mixture starts to gather in the softener
compartment, the siphon must be cleaned.
Wash the detergent drawer and the siphon with
plenty of lukewarm water in a washbasin. Wear
protective gloves or use an appropriate brush to
avoid touching of the residues in the drawer with your
skin when cleaning. Insert the drawer back into its
place after cleaning and make sure that it is seated
well.
Cleaning the water intake filters
There is a filter at the end of each water intake valve
at the rear of the machine and also at the end of
each water intake hose where they are connected to
the tap. These filters prevent foreign substances and
dirt in the water to enter the washing machine. Filters
should be cleaned as they do get dirty.
Close the taps. Remove the nuts of the water intake
hoses to access the filters on the water intake valves.
Clean them with an appropriate brush. If the filters are
too dirty, take them out by means of pliers and clean
them. Take out the filters on the flat ends of the water
intake hoses together with the gaskets and clean
thoroughly under running water. Replace the gaskets
and filters carefully in their places and tighten the
hose nuts by hand.
Draining remaining water and
cleaning the pump filter
The filter system in your machine prevents solid items
such as buttons, coins and fabric fibers clogging the
pump impeller during discharge of washing water.
Thus, the water will be discharged without any
problem and the service life of the pump will extend.
If the machine fails to drain water, the pump filter
is clogged. Filter must be cleaned whenever it is
clogged or in every 3 months. Water must be drained
off first to clean the pump filter.
In addition, prior to transporting the machine (eg.,
when moving to another house) and in case of
freezing of the water, water may have to be drained
12
EN
Advertisement
Table of Contents
