Mocom solstice series Assembly And Installation Manual

Concaved screen

Advertisement

Quick Links

Mocom Concaved Screen – Solstice Series
Assembly / Installation Guide
Please read rules and instruction carefully.
Caution!
The following information should be thoroughly understood before start assembling the product.
The screen surface is vulnerable to external shocks; attention is required when you set it down on the
floor (Please note that strong external shock may affect or damage the screen and a screen curvature)
Please check all components (Bolts, nuts, washers, brackets and the screen)
Select a proper area (indoor) for assembly.
Remove items from your top pocket to avoid them falling out onto the screen surface.
Pull the plastic covering of the screen to a side gently. Do not attempt to apply force with hands or a knife.
If possible, cooperation of two or more is required; one person holds the screen horizontally and the
others can have the plastic easily by pulling it aside. The screen can be placed vertically
Note there are side handles for some models. Please use them to ensure the screens are handled correctly.
While assembling, lean screen surface on the wall in a safe area to prevent from possible damage.
Do not touch the screen surface (The screen surface can be scratched or finger-marked).
Do not touch the screen surface with hard objects.
Alcohol, acetone, organic solvents and other strong cleaning agents are prohibited to remove dirt or debris
on the screen surface. (This may cause damage on the surface of the screen) When cleaning is needed,
wipe any dust from the screen surface with static-free cloth or brush or use dryer with cold air to dust
away.
Please put a screen cover over the screen while the screen is not being used.
Place the screen back in the carton face down
The caster lock wheels must to be in locked location when stationery or when alignment.
Never re-locate screen together with floor stands. Always disassemble screen before move.
In you have any questions regarding the proper assembly, contact your dealer or representatives.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the solstice series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Mocom solstice series

  • Page 1 Mocom Concaved Screen – Solstice Series Assembly / Installation Guide Please read rules and instruction carefully. Caution! The following information should be thoroughly understood before start assembling the product. The screen surface is vulnerable to external shocks; attention is required when you set it down on the ...
  • Page 2 Installation Method by a screen model  MDW-105/125/135 EPDM black frame (22.5mm width) with molded back panel MDW-105S/125S/135S  EPDM black-slim frame (10.5mm width) with molded back panel  DHS-105/125/135 Black velvet finished Aluminum frame (50mm width) with molded back panel DHS-105N/125N/135N ...
  • Page 3: Wall Mounting

    WALL MOUNTING Wall-Hook Type (WH Model) (For: S3D-82, MDW-105/125,/135, MDW-105S/125S/135S, DHS-105/125/135) This Wall-hook type is used when the projector is installed on the ceiling with a low height  and at a place where only a limited adjustment angle of the screen is allowed. Advantage of using this type is a short separation distance between the wall and the screen.
  • Page 4 Installation of Wall-Hook Type  Assemble the accessory (1)Hook Brackets and (2) Angle Adjuster to the screen body. ((1) Hook Bracket can be pre-assembled) Fix the (3) Wall Bracket with screws or anchor bolts on the wall according to an installation height of the screen.
  • Page 5 Wall-Hanger Type (OW-1/2/3) (For: S3D-82, MDW-105/125,/135, MDW-105S/125S/135S, DHS-105/125/135) This wall-hanger type is used when the projector is installed on the ceiling with a tall height  or on the table top. This is applied to a location where space for adjustment of the angle of the screen is enough. ...
  • Page 6 Installation of Wall-Hanger Type (OW-1,2,3)  ① Assemble the accessory (1) Hanger to the screen body using (2) Wing nuts ② Install the (4) Hanger Bracket on the wall using anchor bolts or screws, setting at 6-inches higher than the horizontal axis of the screen.
  • Page 7 Wall-Hanger Type for DHS - 105N/125N/135N (NW) (For: DHS-105N/125N/135N) This model (DHS-XXXN) screen is for a home theater and its frame has a black velvet finishing  job on aluminum. Using a thin back panel, it has excellent design. The black-velvet finished portion absorbs a video image exceeding a margin.
  • Page 8 Installation of Wall-Hanger Type (NW)  ① Assemble the accessory (1) Hanger to the screen body ② Fix the accessory (2) Hanger Bracket on the wall using anchor bolts or screws. ③ Adjust an angle of the screen in order to obtain an optimum brightness and fix it tight.
  • Page 9 Wall mounted by Anchoring on the wall For MDW-155/175/200/220/250 For models with a large screen, there is no back panel but supports with steel frame, and the  screen cannot be installed in a method of the wall bracket. Anchor the screen directly to a wall surface and adjust an angle of the screen according to an ...
  • Page 10 Installation  1) Determine the Anchor bolts locations and mark where you will anchor it. Wall Rear side of the screen 2) Drill holes for the anchor bolts. Wall Hammer Drill Wall Anchor 3) Place the anchor bolt into the cement wall. 4) Lift screen with chain block or other equipment 5) Insert screen into pre-installed anchor bolts 6) Insert anchor nut smoothly.
  • Page 11: Floor Stand

    FLOOR STAND A. Floor stand for MDW/DHS series (OS-1,2,3,4) (For: S3D-82, MDW-105/125,/135, MDW-105S/125S/135S, DHS-105/125/135) This is used when the screen cannot be installed on a wall or when it is installed on the floor as  a movable screen. Supplied accessories include the following. ...
  • Page 12 Horizontal support round pipe with screen angle adjust knob ⑧ Have attention to prevent damage to the screen surface during above-described assembly. Have it covered with bundled nonwoven cloth. stand lower ⑨ A stand frame appropriate for a screen model must be used. Secure the caster in (1) part (Go to the page 15) B.
  • Page 13 ② Assemble (2) Adjustment Hook to assembled (1) Vertical Main stand frame ③ Set a height of the (2) Adjustment Hook according to an installation height of the screen. ④ Lift the screen and connect to the (2) Adjustment Hook ⑤...
  • Page 14 C. Floor-Stand frame by “A” type for MDW-155/175/200/220/250 * The size of the floor stand can vary depending on the model and customer’s request. D. Custom fabrication for installation can be consulted when… 1) None of above methods is applicable 2) Install at a corner, not on a flat wall 3) Hanging with a wire rope is required 4) Install on the access wall...
  • Page 15: Standard Procedure

    Adjustment of a screen angle Mocom Solstice™ concave screen is a precision product which requires proper screen set up procedures for maximum brightness. For the first few times we suggest that you position yourself at the prime viewing audience position to ensure that the angle is set to the brightest position. If the screen angle is not set correctly a substantial amount of image brightness will be lost.
  • Page 16: Screen Alignment

     Chart 1) Optimized Projection Distance Chart of Solstice™ Screen Size 90-125 130-147 155-250 MD-92/103/112, MD-130/147 MDW-155/175/ Screen Model S3D-82 MDW-105/125, MDW-135 200/220/250 DHS-105/125 DHS-135 Miminum 3.7 M (12ft.) 4.5 M (15ft.) 6 M (20ft.) 8 M (26ft.) Projection Distance Screen Alignment Have your assistant stand at the audience position with a projector on and any image being projected on the screen for testing.
  • Page 17 2) For screen angle adjustment, tilt the screen up and down several times while video of a projector is being turned on. Stop tilting at a viewer’s position where the brightest and clearest image for a viewer is seen. Secure the position by using the angle adjuster or the anchor nut (for MD-147 or more).
  • Page 18 3) By watching while repeating sitting and standing at a viewer position, check whether there is any variations in the screen brightness. If there are any variations, repeat the instruction of the above paragraph 2. At the time of judgment, secure the screen with the angle adjuster. 4) In the case of a long projection distance, an image is larger than the screen.

Table of Contents