Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for i3TOUCH Premium P6505 T10
Summary of Contents for i3TOUCH Premium P6505 T10
- Page 1 Premium User Manual Model no. P6505 T10 P7505 T10...
- Page 2 1. Introduction 2. Connecting the Monitor 3. Using the Monitor 4. Cleaning the screen of LCD Monitor 5. Disclaimer 6. Trouble Shooting 7. Supplement 2 | Learn more about i3TOUCH and other product in the i3 line? Visit www.i3-learning.com...
-
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS 1. Please read these instructions carefully before using the product and keep it for later reference 2. Follow all warnings and instructions marked in this manual or on the product. 3. Unplug the power cable from the wall outlet before cleaning. Clean the product with a damp soft cloth. -
Page 4: About The Product
3. Use qualified and safety-approved AC power cord only. 4. The length of cables (HDMI, DP, VGA) should not be longer than 2 meters each. 4 | Learn more about i3TOUCH and other product in the i3 line? Visit www.i3-learning.com... -
Page 5: Check List
1.3 Check List When opening the carton, please make sure that all the items listed below are present: VGA cable (male-to-male) ×1 Power cord ×1 USB cable ×1 (for touch monitor models only) HDMI cable x1 Audio cable 3.5E x1 User guide ×1 Remote control x 1, Battery x 2... - Page 6 (VGA/ HDMI1/ HDMI2/ DP) on rear. Please connect the signal source first, then follow by connecting USB cable for touch. 6 | Learn more about i3TOUCH and other product in the i3 line? Visit www.i3-learning.com...
-
Page 7: Using The Monitor
3. Using the Monitor 3.1 Get to know the monitor The Monitor connectors are located on the rear side. They are shown in the physical monitor as figure below and described in the following paragraphs. Please note that connectors may vary in some derivative models;... -
Page 8: Side View
The outlook of remote control is shown in the Figure, hereafter, Size: 197.2 x 47.1 x 23.2mm (7.7 x 1.85 x 0.9 x in.) Operation distance: < 10 meter (32ft.) 8 | Learn more about i3TOUCH and other product in the i3 line? Visit www.i3-learning.com... - Page 9 Working angle: not more than +/- 40 degrees CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION 3.5 Understanding the OSD Menu (with Remote control) a. Power Press the Power button to turn on/off the monitor. b.
-
Page 10: Return/ Exit
Zoom Press Zoom button to auto-adjust and optimize picture screen of the monitor. BL+/ BL- Press Bl+/ Bl- button to adjust backlight of the monitor. 10 | Learn more about i3TOUCH and other product in the i3 line? Visit www.i3-learning.com... - Page 11 3.4 Content of OSD Menu Picture // press (UP/Down) to select sub menu, press to next page(Sound/ Input) Picture Mode: to select “User” to active sub menu (Contrast/ Brightness/ Colour/ Colour Temperature) User Manual | 11...
- Page 12 Under source VGA the sub menu of (Auto Position/ Auto Color/ PC Setting) will be able adjusted. SETUP // press (UP/Down) to select sub menu, press to next page(Display/ Input) 12 | Learn more about i3TOUCH and other product in the i3 line? Visit www.i3-learning.com...
- Page 13 INPUT // press (UP/Down) to select sub menu, press to next page(Setup/ Picture) User Manual | 13...
-
Page 14: Data Format
The Data has a value of 1, which is the value for ON. The ETX is command End code. 14 | Learn more about i3TOUCH and other product in the i3 line? Visit www.i3-learning.com... -
Page 15: Command Code
3.6.4 Command code Command Note 9/10 Power Input Source HDMI 1 HDMI 2 Android Brightness 100% Plus Minus Language English France German Chinese S Chinese T Volume 100% Down User Manual | 15... -
Page 16: Cleaning The Monitor
VGA Cable to this monitor. 3. The picture is not centered Adjust the H-position, and V-position, or perform the Auto adjustment. 16 | Learn more about i3TOUCH and other product in the i3 line? Visit www.i3-learning.com... - Page 17 4. The screen is flickering Press the “Auto” - adjustment control by remote control or OSD to adjust. Re-locate nearby devices, such as motor, or transformer, which generate magnetic field, away from the monitor. Check if the specific voltage is applied. Check if the signal timing of signal source (PC, IPC, laptop or media player) is within the specification of monitor.
- Page 18 18 | Learn more about i3TOUCH and other product in the i3 line? Visit www.i3-learning.com...