Table of Contents
Advertisement
Quick Links
Air-Conditioners For Building Application
OUTDOOR UNIT
RELAY BOX
PAC-BH02KTY-E
BASE HEATER
PAC-BH01EHT-E, PAC-BH02EHT-E, PAC-BH03EHT-E
INSTALLATION MANUAL
For safe and correct use, please read this installation manual thoroughly before installing the air-conditioner unit.
INSTALLATIONSHANDBUCH
Zum sicheren und ordnungsgemäßen Gebrauch der Klimageräte das Installationshandbuch gründlich durchlesen.
MANUEL D'INSTALLATION
Veuillez lire le manuel d'installation en entier avant d'installer ce climatiseur pour éviter tout accident et vous assurer d'une utilisation correcte.
MANUAL DE INSTALACIÓN
Para un uso seguro y correcto, lea detalladamente este manual de instalación antes de montar la unidad de aire acondicionado.
MANUALE DI INSTALLAZIONE
Per un uso sicuro e corretto, leggere attentamente questo manuale di installazione prima di installare il condizionatore d'aria.
INSTALLATIEHANDLEIDING
Voor een veilig en juist gebruik moet u deze installatiehandleiding grondig doorlezen voordat u de airconditioner installeert.
РУКОВОДСТВО ПО УСТАНОВКЕ
Для осторожного и правильного использования прибора необходимо тщательно ознакомиться с данным руководством по установке
до выполнения установки кондиционера.
PŘÍRUČKA K INSTALACI
V zájmu bezpečného a správného používání si před instalací klimatizační jednotky důkladně pročtěte tuto příručku k instalaci.
NÁVOD NA INŠTALÁCIU
Pre bezpečné a správne použitie si pred inštalovaním klimatizačnej jednotky, prosím, starostlivo prečítajte tento návod na inštaláciu.
TELEPÍTÉSI KÉZIKÖNYV
A biztonságos és helyes használathoz, kérjük, olvassa el alaposan ezt a telepítési kézikönyvet, mielőtt telepítené a légkondicionáló egységet.
PODRĘCZNIK INSTALACJI
W celu bezpiecznego i poprawnego korzystania należy przed zainstalowaniem klimatyzatora dokładnie zapoznać się z niniejszym podręcznikiem instalacji.
INSTALLATIONSHANDBOK
Läs den här installationshandboken noga innan luftkonditioneringsenheten installeras, för säker och korrekt användning.
MANUAL CU INSTRUCŢIUNI DE INSTALARE
Pentru o utilizare corectă şi sigură, vă rugăm să citiţi cu atenţie acest manual înainte de a instala unitatea de aer condiţionat.
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric PAC-BH02KTY-E
Summary of Contents for Mitsubishi Electric PAC-BH02KTY-E
-
Page 1: Installation Manual
Air-Conditioners For Building Application OUTDOOR UNIT RELAY BOX PAC-BH02KTY-E BASE HEATER PAC-BH01EHT-E, PAC-BH02EHT-E, PAC-BH03EHT-E INSTALLATION MANUAL For safe and correct use, please read this installation manual thoroughly before installing the air-conditioner unit. INSTALLATIONSHANDBUCH Zum sicheren und ordnungsgemäßen Gebrauch der Klimageräte das Installationshandbuch gründlich durchlesen. -
Page 2: Table Of Contents
Contents 1. Safety precautions ................ 2 4. Preparation for installation .............7 1.1. Before installation and electric work ......2 5. Installation Procedures ..............9 1.2. Before installation ............2 6. Heater Installation ................10 1.3. Before installation (relocation) - electrical work ..... 2 7. -
Page 3: Before Starting The Test Run
• Be very careful about transporting the product. - One person should not carry the product. Its weight is in excess of 20 kg [45 LBS]. - Some products use PP bands for packaging. Do not use any PP bands as a means of transportation. -
Page 4: Parts List
2. Parts List <PAC-BH02KTY-E> This kit contains the following parts. Parts name Relay Box Installation Manual Shape Qty. A Cable strap B M5 screw C Cable tie (black) D Wire seal Parts name Shape Qty. <PAC-BH01EHT-E> This kit contains the following parts. - Page 5 <PAC-BH02EHT-E> This kit contains the following parts. Parts name Base Heater Shape Qty. * Heater mounting brackets Parts name Shape Qty. * Heater mounting brackets Parts name Shape Qty. Parts name M5 screw Cable tie (blue) Pipe cover Shape Qty. * Use proper mounting brackets according to the outdoor unit model.
-
Page 6: Applicable Models
– PUHY-EP○YHM-A 250, 300 – PUHY-P○YJM-A 200, 250, 300 350, 400 PUHY-EP○YJM-A PUHY-HP○YHM-A 200, 250 – – Europe and PAC-BH02KTY-E PUHY-RP○YJM-A 200, 250, 300, 350 – – other countries PURY-P○YHM-A 200, 250, 300 350, 400 – PURY-EP○YHM-A 250, 300 –... -
Page 7: Preparation For Installation
4. Preparation for installation <PAC-BH01EHT-E> • This base heater and the Relay Box must be installed by a dealer or certified technician. • Refer to the table below for the required mounting brackets for the outdoor unit on which the base heater will be installed. Heater mounting bracket list Heater mounting bracket Accumulator type... - Page 8 <PAC-BH02EHT-E> • This base heater and the Relay Box must be installed by a dealer or certified technician. • Refer to the table below for the required mounting brackets for the outdoor unit on which the base heater will be installed. Heater mounting bracket list Heater mounting bracket Accumulator type...
-
Page 9: Installation Procedures
<PAC-BH03EHT-E> • This base heater and the Relay Box must be installed by a dealer or certified technician. • Refer to the table below for the required mounting brackets for the outdoor unit on which the base heater will be installed. Heater mounting bracket list Heater mounting bracket Wiring fixing bracket... -
Page 10: Heater Installation
6. Heater Installation <PAC-BH01EHT-E> Run the base heater along the groove on the unit base. 2 or 7 Heater mounting bracket Base heater Heater mounting bracket Groove on the base Heater mounting bracket 4 or 5 Heater mounting bracket 1 , 6 Note: The figure shows a simplified view of the unit base without the components on it. - Page 11 Unscrew each screw that is for the base leg and accumulator installation. (1 pc. each) LARGE Accumulator Unscrew a screw that With Oil tank is for the Oil tank installation.
- Page 12 (6)-2 Attach the base heater to the outdoor unit base. Heat exchanger Refrigerant pipe Base heater Insert the left side of the base heater (longer ends) between the heat exchanger and the refrigerant pipes, and bring the base heater down to the outdoor unit base.
- Page 13 (6)-3 Install the heater mounting brackets. * For easier installation of the heater mounting brackets 2 through 5 and 7, use a threaded rod (M5). Follow the steps below. Step 3 Step 1: Install the heater mounting bracket Step 2: Install the heater mounting bracket Step 3: Install the heater mounting bracket...
- Page 14 Step 1. Install the heater mounting bracket 4 or 5. * When using the heater mounting bracket 4 or 5, refer to ”Applicable models” on page 6 and “Heater mounting bracket list” on page 7. For the LARGE Accumulator, install heater mounting bracket 4 as shown in the figure below. Thread part for the Threaded rod (M5) Heater mounting...
- Page 15 Step 2. Install the heater mounting bracket 3. Note) As shown in the figures below, properly secure the base heater and the mounting bracket. Base heater Accumulator support leg Thread part for the Threaded rod (M5) Heater mounting bracket Heater mounting bracket Use the screw (M5) that was removed.
- Page 16 Step 4. Install the heater mounting brackets 1 and 6. Base heater Note) Run the base heater along the inner side of the groove on the base, and fix the base heater with the mounting brackets Heater mounting bracket Base heater Heater mounting bracket Use the screw (M5) that...
- Page 17 <PAC-BH02EHT-E> Run the base heater along the groove on the unit base. Accumulator: Vertical installation Base heater Heater mounting bracket Heater mounting bracket Heater mounting bracket Groove on the base Heater mounting bracket Note: The figure shows a simplified view of the unit base without the components on it. 1 , 9 Heater mounting bracket Accumulator: Horizontal installation...
- Page 18 ● Install the base heater inside the unit by following the procedures (6)-1 through (6)-4 below. Caution: To reduce the risk of injury, wear protective gear when installing the base heater. (6)-1 Unscrew the screws as shown in the figure below. Refer to table “Heater mounting bracket list”...
- Page 19 (6)-2 Install the heater mounting brackets 8 and 9 to the base heater. * Only when the accumulator is installed horizontally Mounting brackets 8 and 9 installation position Installation Heater mounting bracket Base heater Use the supplied Heater mounting screws (M5). bracket Base heater After installation...
- Page 20 (6)-3 Attach the base heater to the outdoor unit base. Heat exchanger Refrigerant pipe Base heater Insert the left side of the base heater (longer ends) between the heat exchanger and the refrigerant pipes, and bring the base heater down to the outdoor unit base.
- Page 21 (6)-4 Install the heater mounting brackets. * For easier installation of the heater mounting brackets 2 through 6, use a threaded rod (M5). Follow the steps below. Step 1: Install the heater mounting brackets , or Step 2 Step 1 Step 3 <Accumulator: Vertical installation>...
- Page 22 Step 1. Install the heater mounting brackets 0 and a, or 4. * When using the heater mounting brackets 0 and a or 4, refer to ”Heater mounting bracket list” on page 8. For the accumulator vertical installation, install heater mounting brackets 0 and a. Base heater Accumulator support leg...
- Page 23 For the accumulator horizontal installation, install heater mounting bracket 4. Base heater Heater mounting bracket Accumulator Thread part for the support leg Threaded rod (M5) Use the screw (M5) that was removed. Note) Properly secure the base heater and the mounting bracket. <Refer to “Note)” in Step 1.>...
- Page 24 Step 2. Install the heater mounting bracket b or 7. * When using the heater mounting bracket b or 7, refer to ”Heater mounting bracket list” on page 8. For the accumulator vertical installation, install heater mounting bracket b. Base heater Heater mounting bracket Oil tank...
- Page 25 Step 3. Install the heater mounting bracket 2 or 3. * When using the heater mounting bracket 2 or 3, refer to “Heater mounting bracket list” on page 8. For PUHY models, install heater mounting bracket 2 . Thread part for the Note) Properly secure the base heater Threaded rod (M5) Heater mounting...
- Page 26 Step 4. Install the heater mounting brackets 1 and 9. Note) Run the base heater along the inner side of the groove Base heater on the base, and fix the base heater with the mounting brackets 1 and 9. Base heater Heater mounting bracket Heater mounting...
- Page 27 <PAC-BH03EHT-E> Run the base heater along the groove on the unit base. Heater mounting bracket Right base heater Heater mounting bracket (right side of the unit) Left base heater Heater mounting bracket (left side of the unit) Heater mounting bracket Groove on the base Heater mounting bracket 4 , 8...
- Page 28 (6)-2 Attach the base heater to the outdoor unit base. Insert the right and left base heaters from the top into the outdoor unit. Left base heater Right base heater (left side of the unit) (right side of the unit) After the base heater is inserted (before the heater mounting brackets are installed) Run the base heater along the groove on the base to keep it...
- Page 29 (6)-3 Install the heater mounting brackets. * For easier installation of the heater mounting brackets 2, 3, and 6, use a threaded rod (M5). Follow the steps below. Step 1: Install the heater mounting bracket Step 2: Install the heater mounting bracket Step 3: Install the heater mounting brackets Step 4: Install the heater mounting brackets Step 5: Install the heater mounting bracket...
- Page 30 Step 2. Install the heater mounting bracket 3. Thread part for the Threaded rod (M5) Heater mounting bracket Use the supplied screw (M5). Note) As shown in the figures below, properly secure the base heater and the mounting bracket. Base heater Heater mounting bracket Base Base...
- Page 31 Step 5. Install the heater mounting bracket 6. Heater mounting bracket Thread part for the Threaded rod (M5) Accumulator Base heater support leg Note) Properly secure the base heater and the mounting bracket. <Refer to “Note)” in Step 2.> Use the screw (M5) that was removed. (Screw down the accumulator support leg as well.) Step 6.
- Page 32 Step 8. Install the heater mounting bracket 7. Note) Run the base heater along the inner side of the groove on the base, and fix the base heater with mounting Base heater bracket 7. Base heater Heater mounting bracket Groove on the base (inner side) Groove on the base Bottom of the base...
-
Page 33: Electrical Wiring
7. Electrical Wiring <PAC-BH01EHT-E> Connect the base heater wiring to the Relay Box as shown in the figures below. Install the Relay Box after connecting the base heater wiring. Base heater Base heater (wiring on the right side) (wiring on the right side) Relay Box Top view of the unit Front view of the unit... - Page 34 <PAC-BH02EHT-E> Connect the base heater wiring to the Relay Box as shown in the figures below. Install the Relay Box after connecting the base heater wiring. Base heater (wiring on the right side) Relay Box Base heater (wiring on the right side) Top view of the unit Front view of the unit Base heater...
- Page 35 <PAC-BH03EHT-E> Connect the base heater wiring to the Relay Box as shown in the figures below. Perform wiring work of the base heater on the right side of the unit first. Install the Relay Box after connecting the base heater wiring. Left side of the unit Right side of the unit Left base heater...
- Page 36 i) Right base heater wiring (right side of the unit) To install the wiring fixing bracket 8 to the compressor cover as shown in the figure below, fix the wiring on the right side of the right base heater to the wiring fixing bracket 8 with the supplied cable strap. Right base heater (wiring on the right side) Wiring fixing bracket...
-
Page 37: Relay Box Installation
8. Relay Box Installation Before installing the Relay Box, replace the control box and wiring as they were. * Insert the cable connectors until they click. Attach the Relay Box to the pillar on the left side of the unit and the plate under the control box, using the three supplied M5 screws. The screw labeled X in the figure is there to keep the Relay Box from falling. - Page 38 <PAC-BH03EHT-E> * PAC-BH03EHT-E base heater does not have a ground connection. Outdoor Heater ground Relay Box Heater SYMBOL EXPLANATION Terminal block Terminal block CN51 Connector (on the outdoor unit controller board) Relay Fuse a. When PAC-BH01EHT-E or PAC-BH02EHT-E is installed, connect the base heater power wires to terminals L1 and L2 on the Relay Box.
- Page 39 <PAC-BH03EHT-E> L1 L1 Never connect the base heater power wire (L1 or L2) After connecting the base heater power wires, check that either of the wires are not connected to For Active Filter Each terminal of two power wires for L1 has a Transmission wires (CN51) white line on the insulation part.
- Page 40 c. Wiring the power wire and earth wire • Disconnect the round terminal connector <TB1-CN1> inside the control box from the connector CN1A (white) and CN1B (white), and from the secondary side of the power supply terminal block. • Connect the power wires (round terminal L1, L2, L3, N) from the Relay Box to the L1, L2, L3, N phase of the power supply terminal block (secondary side) inside the control box together with the existing wires.
-
Page 41: Reassembly
9. Reassembly Reinstall the parts in the reverse order in which they were removed. 10. Confirmation of proper operation Checking the base heater for normal operation (1) Use a tester to check that the heater wire is not broken for proper operation. (2) Check the output voltage for proper circuit operation. - Page 44 This product is designed and intended for use in the residential, commercial and light-industrial environment. The product at hand is • Low Voltage Directive 2006/95/EC based on the following • Electromagnetic Compatibility Directive EU regulations: 2004/108/EC Please be sure to put the contact address/telephone number on this manual before handing it to the customer.