Advertisement
Quick Links
Advertisement
Summary of Contents for Champ DM3112
-
Page 2: Table Of Contents
2M IR Mini Dome Quick Installation Guide Please follow the installation steps below to set up 2M IR Mini Dome IP Camera. Check the package contents against the list below. See P.1 Physical overview. See P.2 I/O Terminal Block Circuit. See P.3 I/O Terminal Block Pin Definition. -
Page 3: Physical Overview. See
Physical overview Dome bubble Top cover Built-in Microphone Ethernet Socket DC 12V/1A External I/O connector Routing hole Light Sensor Lens MicroSD/SDHC IR LEDs (12units, Open the shell alerts Distance 10m) Internal microphone Reset Power LED Indicator Network LED Indicator... -
Page 4: I/O Terminal Block Circuit. See
I/O Terminal Block Circuit I/O Terminal Block Pin Definition This Camera provides an external I/O terminal block which is used to connect input/ output devices. The pin definitions are described below. Definition Description Max. V/A Ground 12V DC + 12V DC 1.2W Connect the wires of the audio input device to GND (Pin 1) and Audio Input... -
Page 5: Led Indicator Definition. See
LED Indicator Definition Color Indication Network Blue Flash blue while Network activity. Steady red for booting up process Blue Steady blue for booting up completion Power Flash purple during firmware upgrading; when reset button pressed for at least 5 sec. Purple to factory default Unlit... -
Page 6: Install The Hardware And Connect All Cables. See
Install the hardware and connect all cables A. Hardware Installation a. Loosen the tamper-proof screws using supplied L-type Hex Key Wrench b. Remove the dome cover. Be careful do not scratch the cover glass. c. If you want to route cable from the side of camera instead of routing hole, please see below figure. 1. - Page 7 B. Wall mount L-type Bracket installation(optional) 1. Position the L-type at the desired installation location. Drill two holes into the placement and hammer the included screw anchors. 2. Align the two holes on the L-type bracket to the two plastic anchors on the wall or ceiling, insert the supplied screws to the corresponding hole and fix them.
- Page 8 C. Outdoor wall mount kit installation(optional) 1. Position the outdoor kit at the desired installation location. Drill two holes into the placement and hammer the included screw anchors. 2. Assembly silicone rubber and outdoor kit together. 3. Combine O-ring and supplied screws together, then insert to the corresponding hole and fix them. 4.
- Page 9 D. Outdoor Wall mount kit and L-type Bracket installation(optional) 1. Position the L-type at the desired installation location. Drill two holes into the placement and hammer the included screw anchors. 2. Align the two holes on the L-type bracket to the two plastic anchors on the wall or ceiling, insert the supplied screws to the corresponding hole and fix them.
- Page 10 E. Wall mounting and Ceiling mounting 1. Attached the alignment sticker to the wall/ceiling. Drill three holes into the wall, which two for screws and one for cable. 2. Hammer the supplied plastic anchors into the holes. 3. Align the two holes on the base of camera with the two plastic anchors on the wall or ceiling, insert the supplied screws to the corresponding hole and screw them.
- Page 11 To adjust the view angle- 3 axis Mechanism Design 1. Turn the lens module right and left to your desired pan position. 2. Turn the lens module up and down to your desire tile position. 3. Turn the lens module to adjust the image orientation to satisfied angle. H.
- Page 12 Important: Do not rotate the IR LEDs so that it gets blocked by the housing as it will affect the IR performance (as shown below). If the image is upside down, please use the image rotate function in Video Setting. Completion 1.
- Page 13 Microsoft OS: Go Website download Camera Installation Tool Please go http://www.champsolution.com/DownloadMainpage.php download “Camera Installation Tool”. Andfollow the installation process to complete the installation. Access the IP Camera using Intelligent IP Installer 1. Please check two settings before using Intelligent IP Installer . b.
- Page 14 3. Enter your Username and Password to login to the IP Camera. (Default is admin / admin) 4. When accessing the IP Camera for the first time, a yellow information bar appears below the address bar: his website wants to install the following add-on: ‘AxvideoView.cab’. 5.
- Page 15 Mac OS using Safari Browser 2. Click Bonjour function and select the camera 1. Select Safari icon you wish to access. 3. Enter name and password to login to the IP 4. The monitor image will be displayed in your browser. camera.
- Page 16 The default setting of lighting environment is Auto. However, you may also select 50 or 60 Hz upon the lighting environment of your country. Go to “Setting > Live View > Camera Setting > Image Setting”, select the environment setting you wish. Change the Web Interface into your preferred language Use the settings screen to set the language of the Web Interface.
- Page 17 Application of IP Camera...