Summary of Contents for Terratek T12VOS
- Page 1 12V Li-ion Cordless Orbital Sander T12VOS User Manual — Please read and retain for future reference. IMPORTANT: Read all instructions before use.
- Page 2 Contents Parts List Technical Information Safety Instructions Using your sander Maintenance Warranty Parts List Description Description Sander paper Gear Screws ST3.5X8 Small gear Screws ST2.2X10 Needle bearing Flat plate screws M3X6 Fixed plate Spring Washer Screws ST3X14 Locator card Plate Motor Right sleeve Right housing...
- Page 3 Exploded Assembly Diagram NOTICE: Actual product may vary from pictures shown.
- Page 4 fig.1 1. Sanding Pad 2. On/Off switch 3. Soft grip handle 4. Battery pack Battery capacity indicator LED 5. Charger Tabs Charge indicator fig.2...
- Page 5 Technical Information Model: T12VOS Rated Voltage: 12V DC No-load Speed: 10000 /min Orbital diameter: 1.6 mm Battery Type: 1300 mAh Li-ion Charger Charging time: 1 hour Input: 100-240V AC, 50 – 60 Hz, 27W Output: 12.6V DC, 1500mA Max Read this entire manual before using this product.
-
Page 6: Important Safety Information
Read and Keep This Manual Please read carefully all instructions within this manual. Failure to follow all safety warnings can result in serious personal injury. The term “Power Tool” in all of the following warnings refers to your mains operated (corded) or battery operated (cordless) power tool. Important SAFETY Information This symbol is to warn you of potential personal injury hazards. -
Page 7: Electrical Safety
Electrical safety Before use, ensure that the power outlet you are using matches the plug on your power tool and that the voltage of the outlet matches that of your power tool. Only use grounded extension cords with power tools fitted with 3 pin plugs and if using outdoors ensure any extension cord is suitable for outdoor use. -
Page 8: General Safety Instructions
Service Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Develop a periodic maintenance schedule for your tool. When cleaning a tool be careful not to disassemble any portion of the tool since internal wires may be misplaced or pinched or safety guard return springs may be improperly mounted. - Page 9 9. USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
- Page 10 26. NEVER LEAVE TOOL RUNNING UNATTENDED. Turn power off. Don’t leave tool until it comes to a complete stop. 27. Double Insulation eliminates the need for the three wire grounded power cord and grounded power supply system. This power tool is supplied with all the relevant safety guards and features, it should be checked before every operation, this manual should be read and kept in a safe place.
- Page 11 When working with the machine, always hold it firmly with both hands and provide for a secure stance. The power tool is guided more secure with both hands. Keep your workplace clean. Blends of materials are particularly dangerous. Dust from light alloys can burn or explode.
- Page 12 Symbols IMPORTANT: Some of the following symbols may be used on your tool. V…………………………volts A…………………………amperes Hz……………………….hertz ~…………………….….alternating current …/m………………..revolutions per minute .....class II construction (double insulated) Kg………………………..kilograms ………………………..No load speed ……………….…..Conforms to European Harmonised New Approach Directives. DC ………………..…….Direct Current Battery use and care A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery.
-
Page 13: Overload Protection
Overload Protection The power cutter is fitted with an overload/overheat protection device. When the tool is forced to work at an excessive load, the protection device will be activated automatically to disconnect the power supply. If this occurs, switch off the tool and switch on again to resume the work, make sure to apply only suitable workload to the tool. -
Page 14: Specific Safety Rules
ADDITIONAL PRECAUTIONS FOR CHARGER & BATTERY PACK 1. Do not charge battery pack when temperature is below 10°C (50°F) or above 40°C (104°F). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything to cover or clog the charger vents. 4. -
Page 15: Package Contents
Use special precautions when sanding chemically pressure treated lumber, paint that may be lead based, or any other materials that may contain carcinogens. A suitable breathing respirator and protective clothing must be worn by all persons entering the work area. Work area should be sealed by plastic sheeting and persons not protected should be kept out until work area is thoroughly cleaned. -
Page 16: Switching On And Off
Installing or removing battery pack. 1. To remove the battery pack, withdraw it from the tool while depressing the tabs (Fig.2) on both sides of the battery pack. 2. To insert the battery pack, align the ribs on the top of the battery with the grooves in the housing and slide it into place. - Page 17 LED Capacity indicator: (Fig.2) Once only the one LED is lit, the battery must be re-charged. Disposal of the exhausted battery WARNING: Do not dispose of the exhausted battery. The battery must explode if it is incinerated. The product that you have purchased contains a rechargeable battery.
- Page 18 Accessories CAUTION: Use only accessories or attachments recommended for use with your Terratek tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
- Page 19 We ACL Group (Intl.) Ltd, England DN6 8LZ declare that the cordless sander has been manufactured according to our full quality assurance procedures. The declaration is to certify that it conforms to CE, EMC, MD and RoHS directives: EN55014-1/A1:2009 EN55014-2/A2:2008 All provisions of Annex 1 of Council Directive 2004/108/EC –...
-
Page 20: Environmental Protection
Environmental Protection RECYCLING: WASTE ELECTRICAL PRODUCTS SHOULD NOT BE DISPOSED OF WITH HOUSEHOLD WASTE. PLEASE RECYCLE WHERE FACILITIES EXIST. CHECK WITH YOUR LOCAL AUTHORITY OR RETAILER FOR RECYCLING ADVICE. Please read the following carefully ACL Group (Intl) Ltd. and/or it’s distributor has provided the parts list and assembly diagram as a reference tool only.
Need help?
Do you have a question about the T12VOS and is the answer not in the manual?
Questions and answers