TP-Link TL-WR802N Quick Installation Manual

Quick

Installation Guide

300Mbps Wireless N Nano Router
MODEL NO. TL-WR802N
REV1.0.4
7106505657
During Travel
Wireless Router (Default)
Internet
D
Hotspot Router
Tips: In this mode, devices can connect to the Internet via the LAN port and wireless simultaneously.
Public
Wi-Fi Network
Name
Public
Wi-Fi
Other Information
Router Ports and LED:
LED
Determine Operation Mode
Operation Modes
Wireless Router
Travel
Hotspot Router
Range Extender
Home
Client
Access Point
TL-WR802N's
Wi-Fi Name:
TP-LINK_X X X X
A
B C
TL-WR802N's
Wi-Fi Name:
TP-LINK_X X X X
A
B
LED Status Indication
Solid
The router is connected to the root Wi-Fi network or Internet.
Blinking steadily: The router is disconnected from the root Wi-Fi
Blinking network or Internet.
Blinking irregularly: The router is booting or updating firmware.
Port Description
Functions as the LAN port in Hotspot Router, Range Extender,
LAN/WAN and Access Point mode.
Functions as the WAN port in Wireless Router mode.
Connects to a USB charger, power adapter or computer USB
Power
port via the provided Micro-USB cable for power supply.
Resets the router to its factory default settings, please refer
Reset
to Frequently Asked Questions (FAQ) for instruction.
Application
To share a wired (Ethernet) connection to wireless devices, such as in a hotel room, small office, etc.
To create your personal Wi-Fi hotspot from a public Wi-Fi network such as in a hotel room, trade show, etc.
To extend the range of an existing Wi-Fi network.
To function as a wireless adapter to connect your wired device (e.g. Blu-ray® player, smart TV, or game
console) to a wireless network.
To set up a Wi-Fi network from an existing wired (Ethernet) network.
1 Connect the router according to steps A to D in the left diagram.
2 Wait until the router boots up, about 30 seconds, then use the default Wi-Fi Name and Password printed
on the Wi-Fi Info Card to connect to the router.
Check the Internet connection on your laptop or smartphone, and please note that:
- If you can access Internet without any restriction, no other configuration is required.
- If you're redirected to a splash page authentication, please complete it to access the Internet.
- If you want to customize your own wireless network, continue with the steps below.
3 Launch a web browser and type http://tplinkwifi.net into the address bar. Enter admin (in lowercase) for
both user name and password.
4 Click Quick Setup on the left panel, and click Next to start configuring the router. Select Wireless Router
mode and click Next.
5 Select the WAN Connection Type of your Internet Service Provider and follow the screen instructions to
configure the parameters. When using the router in a hotel room or a small office, please select Dynamic
IP.
6 On the Wireless screen, either keep the default Wireless Network Name and Wireless Password or
customize them, then click Next.
7 Click Finish to complete the configuration.
8 Please note the additional steps to be completed once the Nano router is
If you change the default Wi-Fi name and password, you will need to reconnect your wireless
devices to the new Wi-Fi network.
1 Connect the router according to steps A to C in the left diagram.
2 Wait until the router boots up, about 30 seconds, then use the default Wi-Fi Name and Password printed
on the Wi-Fi Info Card to connect to the router.
3 Launch a web browser and type http://tplinkwifi.net into the address bar. Enter admin (in lowercase) for
both user name and password.
4 Click Quick Setup on the left panel, and click Next to start configuring the router. Select Hotspot Router
mode and click Next.
5 Select the WAN Connection Type of your Internet Service Provider and follow the screen instructions to
configure the parameters. When using the router in a hotel room or a small office, please select Dynamic
IP.
6 Select the public Wi-Fi that you want to connect to, and click Next.
7 Type in the public Wi-Fi password when prompted. In the AP settings section, customize your Wi-Fi
network name and password, then click Next.
8 Click Finish to complete the configuration.
9 Please note the additional steps to be completed once the Nano router is
C
If you change the default Wi-Fi name and password, you will need to reconnect your wireless
devices to the new Wi-Fi network.
Wi-Fi Info Card:
300Mbps Wireless N Nano Router
Wi-Fi Name(SSID):TP-LINK_XXXX
Wi-Fi Password/PIN:XXXXXXXX
Use the default Wi-Fi Name and password
to connect wirelessly.
Using Amazon Fire TV Stick or Chromecast
when traveling:
802
(SSID):
/PIN:
Connect your laptop, smartphone or
tablet to the router.
Plug the HDMI streaming stick directly
TV
into the hotel TV.
Follow the onscreen instruction to
connect to the router's Wi-Fi.
Enjoy streaming content on the TV.
rebooted.
rebooted.
TV
TV