Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Zhejiang NVR500 Series
Summary of Contents for Zhejiang NVR500 Series
- Page 1 NVR500 Series Network Video Recorders Quick Guide Manual Version: P100‐20140128 ...
- Page 2 © 2014, Zhejiang Uniview Technologies Co., Ltd. and its licensors All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Zhejiang Uniview Technologies Co., Ltd. Notice The information in this manual is subject to change without notice. Every effort has been made in the preparation of this manual to ensure accuracy of the contents, but all statements, information, and recommendations in this manual do not constitute the warranty of any kind, express or implied. Environmental Protection This product has been designed to comply with the requirements on ...
- Page 3 chassis, contact the local agent of our company for help. Otherwise, we shall not be held liable for any consequence caused thereby. Make sure the device is sturdy and well grounded and meets heat dissipation and lightning protection requirements. Avoid vibration when using the device. Provide a stable and compliant power supply before powering on the device. Before performing the verification (refer to section “Check Before Power‐On”), make sure that the power is disconnected, for fear of bodily injury or equipment damage caused by incorrect cable connection. ...
- Page 4 Safety Information WARNING! Installation and removal of the unit and its accessories must be carried out by qualified personnel. You must read all of the Safety Instructions supplied with your equipment before installation and operation. Warnings: If the product does not work properly, please contact your dealer or the nearest service center. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) To reduce the risk of fire or electrical shock, do not expose this product to rain or moisture. ...
- Page 5 Caution: Fiber optic ports – optical safety. Never look at the transmit laser while the power is on. Never look directly at the fiber ports and the fiber cable ends when they are powered on. Caution: Use of controls or adjustments to the performance or procedures ...
- Page 6 LVD/EMC Directive This product complies with the European Low Voltage Directive 2006/95/EC and EMC Directive 2004/108/EC. WEEE Directive–2002/96/EC The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and must be disposed of in a responsible manner. ...
-
Page 7: Table Of Contents
Contents 1 Overview .................... 1 2 Appearance ................... 1 Front View ..................... 1 Indicators ...................... 1 Rear View ...................... 3 Interfaces ...................... 4 3 Mounting .................... 5 Installation Check .................. 5 Installing Hard Disks .................. 6 Installing the Equipment ................ 8 Mounting to the Workbench .............. 8 Mounting into a Cabinet ............... 8 Installing a Power Module (Optional) ............ 9 Installing the Decode Card (Optional) ... - Page 8 Soft Shutdown through Web Interface .......... 1 7 6 Common Configurations .............. 18 Man‐Machine Interface ................ 1 8 About the Interface ................ 1 8 Menu Structure .................. 1 9 Initial Configuration .................. 1 9 Quickly Adding IPC .................. 2 5 Preview ....................... 2 8 Pane Toolbar on the Preview Interface .......... 2 8 Preview Status .................. 2 9 Right‐click Context Menu .............. 3 0 Recording .................... ...
-
Page 9: Overview
1 Overview As new‐generation network video recorder for professional clients and commercial customers, NVR500 series incorporates a wide range of features including video management, data management, iSCSI storage, media switch. Delivering characteristics of high performance, stability and capacity, NVR500 uses the redundancy design in key components and provides a rich set of extensible interfaces for different applications ... - Page 10 Table 2‐1 Status Indicators Status Indicators Color Description Constantly on Network properly connected NET Green (network indicator) Off No network connection Constantly on Power connected PWR Green (power indicator) Off No power Constantly on Device is selected and can be remotely controlled IR Blinking Device is being Green verified (remote control indicator) Off Device is not selected and cannot be remotely controlled Constantly on Running normally ...
-
Page 11: Rear View
Status Indicators Color Description Off Hard disk is not installed or the ‐ system shuts down, or the indicator turns red Constantly on Equipment alarms ALM Off The system runs Red (alarm indicator) normally without alarms Rear View NVR516‐128‐IN NVR516‐64‐IN 3 ... -
Page 12: Interfaces
Interfaces As shown in the rear view, the following table describes interfaces on the rear panel. Table 2‐2 Interfaces Function and No Item Description Instructions Compatible with RS485 Connecting to RS485 RS‐485/422 and RS422 serial ports or RS422 devices Interface and RJ45 connectors AC 100V ‐ AC power, 100V‐240V Connecting to the 240V AC power supply Turn on/off device when connected to power Note: POWER ... -
Page 13: Mounting
Function and No Item Description Instructions Holding the button for five seconds restores RST Button Reset button the factory default settings Allow you to stop the Power running system Soft shutdown button Button processes when the device is powered on 2 mini SAS (only miniSAS Network storage available in interface expansion unit NVR516‐128‐IN) eSATA Interface with external Connecting to eSATA (Optional) storage device hard disk Connecting to an USB2.0 interface, USB Interface external USB mouse or limited to 1A storage device Compatible with RS232 Connecting to devices ... -
Page 14: Installing Hard Disks
Installing Hard Disks For supported hard disk types, consult our authorized sales or technical support staff.The following examples illustrate how to install hard disks on a workbench. The installation process may vary according to conditions. The hard drive interface is located inside the device. You need to remove the front panel to install the hard disk.The hard disks are hot‐swappable and support mixed insertion. The disks can be powered on in order to minimize the impulse current produced during the power‐on process. WARNING! ... - Page 15 Align the hard disk with the slot and push in the hard disk gently and steadily. Push the hard disk in position with your thumb until the buckles click.Repeat the above steps to install all the hard disks. Cover the front panel and fix the screws to secure the front panel. 7 ...
-
Page 16: Installing The Equipment
Installing the Equipment The equipment provides front, side and back ventilation channels. Leave room of at least 30cm to the front and back and 10cm to the left and right sides of the equipment for ventilation. Mounting to the Workbench Get the stickers from the foot pads delivered with the equipment, and attach the pads to the bottom of the equipment where appropriate. Place the equipment on a clean workbench. Now the installation process is complete. ... -
Page 17: Installing A Power Module (Optional)
Perform the same procedure to mount the suspension loop on the other side of the chassis. 1: Screws (4) 2: Slotted hole 3: Suspension loop Place the equipment on the cabinet support, and slid it into the cabinet. Fix the suspension loop to the floating nut to the front mounting bar of the cabinet with screws led through the slotted hole. ... -
Page 18: Installing The Decode Card (Optional)
Installing the Decode Card (Optional) WARNING! Before you install the decode card, ensure that you hace powered down the device to avoid personal injury or device damage. Please wear anti‐static gloves when installing the decode card. The device supports 4/6‐channel HDMI audio & video decoder. You can choose the desired decoder as required. Install a power module as follows: 1: Loosen one screw to remove the 2: Insert the decode card cover. 3: Thread and tighten the screws. 10 ... -
Page 19: Connecting Cables
4 Connecting Cables Connecting to Alarm Input/Output Device Twisted pair is recommended. 22‐28AWG insulating core wire, preferably 24AWG or 26AWG can be used. 1: Any terminal on the ALARM IN interface 2: Alarm input circuit inside the device 3: Ground 4: Terminal G on ALARM IN interface 5: Normal open/closed Boolean alarm input device 1: Alarm output circuit inside the device 2: Any positive terminal on ALARM OUT interface 3: Boolean alarm output device 4: DC power 5: Any negative terminal on ALARM OUT interface, corresponding to 2 11 ... -
Page 20: Connecting To A Third-Party Device
1: Alarm output circuit inside the device 2: Any positive terminal on ALARM OUT interface 3: Boolean alarm output device 4: AC power 5: Any negative terminal on ALARM OUT interface, corresponding to 2 Connecting to a Third‐Party Device The device supports two types of RS485 interface: RJ45 and Phoenix connector for connection with third‐party devices. RS485 Serial Cables Twisted pair is recommended. 22‐28AWG insulating core wire, preferably 24AWG or 26AWG can be used. Refer to the table below for the maximum length of RS485 serial cables with different baud rates. ... -
Page 21: Connecting To A Third-Party Device Via Rs485 Interface
Connecting to a third‐party device via RS485 interface Use an RS485 （422 compatible） connector under the RJ45 category to connect to a third‐party device. A third‐party device control cable must be an RS485 cable that meets the following requirements: • The RJ45 connector's T+ and R+ terminals are shorted and then connected to the third‐party device's RS485+ connector; the RJ45 connector's T‐ and R‐ terminals are shorted and then connected to the ... - Page 22 • If the third‐party device is grounded, the third‐party device control cable's Terminal G is connected to the RJ45 connector's Terminal G (No.7 or 8). 1: Third‐party device RS422 control cable 2: Twisted pair Connect a third‐party device using a Phoenix connector's RS485 terminal. Do as follows: • Connect the Phoenix connector's Terminal A to the RS485 terminal of the third‐party device; Terminal B to the RS485‐ terminal of the third party device as shown below. • If the third‐party device is grounded, the third‐party device control cable's Terminal G is connected to Terminal G of the Phoenix connector. 1: RS485+ 2: RS485‐ 3: Third‐party device control cable 14 ...
-
Page 23: Connecting Rs232 Serial And Network Cables
CAUTION! Connect to a special‐purpose keyboard using the phoenix connector's RS485 的 3A、3B interface terminal similarly to connecting a third‐party device. Connecting RS232 Serial and Network Cables Through an RS232 serial port, connect the equipment to a serial device such as a PC. For maintenance, use the following serial cables (take PCX‐based DB9 as an example). 1: DB9 interface 2: RJ45 interface As shown in the following figure (NVR516‐128‐IN as an example), please connect the RS232 serial and network cables as required. The following figure provides an example of connection through an electrical interface.Connect ... -
Page 24: Connecting A Groundcable
1: PC 2: Network cable 3: Serial cable Connecting a Groundcable To ensure personal and equipment safety(lightning protection and resistance against interference), ground the device properly. The ground cable must not exceed 30m and provide a grounding resistance of less than 5 Ω. For specific requirements, refer to the standards for the IEC61024 series. ... -
Page 25: Turning On The Device
• The device is firmly and securely installed without any screw left unscrewed. • Do not place anything on the device. • All the installed cables are connected correctly. • Use a power supply approved for the device. Turning on the Device Connect the power supply and power on the device. If the power LED indicator on the backplane of the device is lit, it indicates that the device is powered on successfully. Soft Shutdown Soft shutdown means a device is turned off to terminate the running system ... -
Page 26: Common Configurations
WARNING! In the course of normal operation of the equipment or device is closed, do not disconnect the power while the equipment is running properly or shutting down, so as to not to damage the equipment 6 Common Configurations The NVR500 Series can be operated through man‐machine and Web interfaces. Man‐Machine Interface About the Interface After the device starts, enter the man‐machine interface when the display shows a progress bar.You can use the mouse or the front panel for configuration and service monitoring on the man‐machine interface. 18 ... -
Page 27: Menu Structure
Menu Structure Menu Backup Configuration Camera Storage Alarm Network Maintenance Help Record IR Remote Basic Array Alarms Basic Boolean Control Playback Montion PPPoE Preview Storage Toolbar Detection PTZ Tamper‐ informatio System Server Toolbar proof Info About the Video Loss SMTP Backup device Device ... - Page 28 Enter the admin user's password (admin by default). Click Next and the interface of Configuration Wizardinterface appears. Configure the network parameters. Click Network Configuration to enter the Network Configuration interface. 20 ...
- Page 29 On the Basic tab, configure the IP address, subnet mask, and default gateway.Normally, set other network parameters to defaults. After configuration, click OK. Configuring eth0 card causes the system to restart service and then return to the Configuration Wizard interface. 21 ...
- Page 30 Configure system parameters. Click System Configuration. The System Configuration interface appears. In the Server Configtab, select the management mode based on the actual networking conditions.Normally, set other system parameters to defaults. After configuration, click OK.Changing the management mode will restart the device. Configure storage parameters. Click Storage Configuration. The Storage Configuration interface appears. Building an array In the Build Array box under the Array tab, enter the array name, select the array type, and idle slots; Click Create. The newly created array is shown on the array list. 22 ...
- Page 31 Virtualizing anarray Be sure to virtualize an array before using it. To do so, select the array in the Virtualization Array box and click Virtualization. NOTE! Virtualization takes time. After virtualization is complete, "virtualized" in the array list is displayed as "Yes". 23 ...
- Page 32 Configuring storage resources On the Storagetab, configure storage resource parameters. The following table lists the important parameters. Configuringstorage plans 24 ...
-
Page 33: Quickly Adding Ipc
On the Storage tab, click Storage Plan to configure a general or exceptional storage plan. After configuration, click OK. The system returns to the Storage Configuration tab. iii. Click OK. The system returns to Configuration Wizard interface. NOTE! On the day of exception plan, only storage plans outside of the exception ... - Page 34 Add our company's IPC. • Add single IPC: Select one of our IPCs you want to add. The IPC parameters are displayed below the list.(You can modify related parameters, Important parameters are described in the following table.) Click Add to add the IPC. • Add IPCs in batches: Select a number of our IPCs you want to add. Click Batch Add and the system will add IPCs in batches according to ...
- Page 35 Adding third‐party IPCs • Add single third‐party IPC: Select a third‐party IPC you want to add. The IPC parameters are displayed below the list. (You can modify related parameters, important parameters are described in the following table.) Click Add to add the IPC. • Add IPCs in batches: Select a number of third‐party IPCs you want to add. Click Batch Add and the system will add IPCs in batches according to default parameters. ...
-
Page 36: Preview
Preview Pane Toolbar on the Preview Interface In preview mode, click a pane. A toolbar related to the pane appears below the pane. Table 6‐1 Button Description in Pane Toolbar Icon Name Description Stop live Stops playing the live video in the current pane Click this button to enter the PTZ control PTZ control interface in preview mode. Records the live video in the current pane to a Manual local destination. Click the button again to stop record manual recording. Instant Plays back the videos recorded within 5 minutes ... -
Page 37: Preview Status
Icon Name Description Note: Images captured are stored by date in the root directory of your USB drive (a folder is automatically created and named "snap_ date").For example, images captured on March 24, 2013 are stored in a folder named "snap_2013‐03‐24". Before capturing images, ensure that you have inserted a USB drive into the device. ... -
Page 38: Right-Click Context Menu
Icon Name Description Fan alarm This icon is shown when a fan alarm occurs. Boolean input This icon is shown when a Boolean input alarm channel alarm occurs. Alarm This icon is shown when alarm triggering triggering preview screen occurs. This icon is shown when a shield alarm Shield alarm occurs. Mute This icon is shown in mute mode. Manual record This icon is shown in manual record mode. Right‐click Context Menu In the preview screen, the right‐click context menu is shown in the following figure. Menu functions are described in the following table. ... - Page 39 Table 6‐3 Preview Operations Menu Item Description When the selected pane switches to a digital channel screen, you can start or stop previewing digital channels such as IPC. Note: Camera When the camera connected on the channel gets offline, the corresponding digital channel will become unavailable. You can perform preview only when the camera comes online. Displays the images available for preview on the Prev Screen/ previous or next screen based on current split screen Next Screen mode and screen number during polling switching. Switches the split‐screen mode. ...
-
Page 40: Recording
Recording This article describes how to manually record audio and video data on different channels and store the data to a hard disk. On the preview screen, select a pane for video recording. Click Manual Record to start recording. An icon will appear above the pane. To stop manual recording, click Stop Recording on the toolbar. Playback The device can play back the videos recorded within 5 minutes before the current time point to facilitate instant playback in case of exceptions. ... -
Page 41: Prerequisites
Prerequisites • The USB storage device is FAT32‐partitioned and formatted, and properly connected to the device. • You are permitted to play back videos. • Ensure that video records are stored on the device's hard disks. Procedure Access the interface for record backup interface. To do so, choose Menu>Recording Backup. Query videos. After selecting one or more channels on which you want to query video records. Enter the start/end time. Click Query to display search results. Select video records you want to back up. Select one or more video records you want to back up. Click Backup to enter the backup interface. 33 ... - Page 42 CAUTION! After selecting the channel and entering the start/end time, click Quick Backup. On the interface for record backup, all the video records within the specified time periods on the selected channel will be backed up by default. Select the backup path. Select a partition of a USB storage device from the USB drive drop‐down list.Select a folder, or double‐click to enter the directory and then select a folder. Backing up a video Click Backup to start video backup. 34 ...
- Page 43 CAUTION! During the backup process, the progress bar will show "backing up X/Y:" x indicates the video records currently being backed up; y represents the total number of video records you want to back up.During the backup process, click Cancel on the progress bar to stop video backup. 35 ...
-
Page 44: Web Interface
NOTE! If the duration of a video record for backup is less than half an hour, the record will be saved as a separate file; if the record exceeds half an hour, the record will be automatically split into half‐hour units and saved as separate video files. A backup video file is named as follows: camera name‐video start time‐end time‐random value.file format.For example: camera 01‐20121222000000‐20121223103000‐719885386.ts. Click Refresh to show the free and full capacities of the current partition on the USB storage device. ... -
Page 45: Specifications
After successfully logging in to the web interface, perform related configuration operations. 7 Specifications For more information about technical specifications of the device, refer to the datasheets. Item Description Hard disk interface 16 SATA interfaces NVR516‐128‐IN can connect to two network mini SAS extended storage expansion unit at the same time and Interface support up to 32 hard disks 2U high Dimensions (W × D × 130.5mm×477.1mm×481.6mm (with front H) panel) Power supply 90V‐230V AC; 50Hz/60Hz Consumption <200W (16 SATA Hard disks) Working temperature ‐10℃ to +55℃ Working humidity 10% to 90% (noncondensing) Working altitude ... - Page 46 Bit Rate (Kbps) Storage Used (GB) 1536 17.402 2048 23.203 3072 34.805 4096 46.406 38 ...
- Page 47 BOM: 3101C032 ...