Advertisement
Select [OK] and press ENTER ( ) to apply network settings. 5. The unit will ask you to test the network connection.
Select [OK] and press ENTER ( ) to complete the network connection. 2. The [CONNECTION SETTING] menu appear on the screen. Use U/u to select the
If you select [Test] and press ENTER ( ) at step 5 above, the network connection status is displayed on the screen. You can also test it on the [Connection
Status] in the [Setup] menu. 3. Use U/u/I/i to select the IP mode between [Dynamic] and [Static]. Normally, select [Dynamic] to allocate an IP address
automatically 22 Installation Wireless Network Connection Another connection option is to use an Access Point or an wireless router. In the example
configuration for wireless connection below, this unit would be able to access content from either of the PCs. The network configuration and connection
method may vary depending on t he equipment in use and the network environment. This player is equipped with an IEEE 802.11n (2.4 GHz band only)
11b/g standards. For the best wireless performance, we recommend using a IEEE 802.11n certified Wi-Fi network (access point or wireless router). Wireless
Network Connection Front of this unit Refer to the setup instructions supplied with your access point or wireless router for detailed connection steps and
network settings. NOTE For best performance, a direct wired connection from this player to your home network's router or cable/DSL modem is always the
best option. If the player is far away from your router or cable/DSL modem, Ethernet or LAN cables are available at many stores in lengths of 50 feet and
longer. If you do chose to use the wireless option, note that performance can sometimes be affected by other electronic devices in the home. 3 Installation
Wireless Network Setup For the wireless network connection, the player needs to be set up for network communication. This adjustment can be done from the
Setting up the access point or the wireless router is required before connecting the player to the network. Wireless Communication PREPARATION PC
Before setting the wireless network, you need to: - connect the broadband internet to the wireless home network. - set the access point or wireless router. -
Select the [Connection Setting] option in the [Setup] menu then press ENTER ( ). WAN Access Point or Wireless Router Broadband service Installation 23 2.
The [CONNECTION SETTING] menu appear on the screen. Use U/u to select the [Wireless] and press ENTER ( ). NOTE · WEP security mode generally
If your access point or wireless router use WEP security, enter the security code of the key "No.1" to connect on your home network. · An Access Point is a
device that allows you to connect to your home network wirelessly. 3. Selects [OK] and press ENTER ( ) to continue. The new connection settings resets the
current network settings. [Manual] Your access point may not be broadcasting its access point name(SSID). Check your router settings through your
computer and either set your router to broadcast SSID, or manually enter the access point name(SSID) in [Manual]. [Push Button] If your access point or
wireless router that supports Push Button Configuration method, select this option and press the Push Button on your access point or wireless router within
120 counts. You do not need to know the access point name (SSID) and security code of your access point or wireless router.
5. Use U/u/I/i to select the IP mode between [Dynamic] and [Static]. Normally, select [Dynamic] to allocate an IP address automatically. 3 Installation 4.
The unit scans the all available access points or wireless routers within range and display them as a list. Use U/u to select an access point or wireless router
on the list, and then press ENTER ( ). If you have security on your access point or wireless router, verify that the WEP or WPA key that was entered into the
player matches the router's information exactly. You need to input the security code as necessary. 24 Installation Notes on Network Connection: NOTE If
there is no DHCP server on the network and you want to set the IP address manually, select [Static] then set the [IP Address], [Subnet Mask], [Gateway] and
[DNS Server] using U/u/I/i and numerical buttons. If you make a mistake while entering a number, press CLEAR to clear the highlighted part.
· Many network connection problems during set up can often be fixed by re-setting the router or modem. After connecting the player to the home network,
quickly power off and/or disconnect the power cable of the home network router or cable modem. Then power on and/or connect the power cable again.
Depending on the internet service provider (ISP), the number of devices that can receive internet service may be limited by the applicable terms of service.
Our company is not responsible for any malfunction of the player and/or the internet connection feature due to communication errors/malfunctions associated
with your broadband internet connection, or other connected equipment. The features of BD-ROM discs made available through the Internet Connection
feature are not created or provided by our company, and our company is not responsible for their functionality or continued availability. Some disc related
material available by the Internet Connection may not be compatible with this player. If you have questions about such content, please contact the producer of
Even if the unit is properly connected and configured, some internet contents may not operate properly because of internet congestion, the quality or
bandwidth of your internet service, or problems at the provider of the content. Some internet connection operations may not be possible due to certain
restrictions set by the Internet service provider (ISP) supplying your broadband Internet connection. 6. Select [OK] and press ENTER ( ) to apply network
settings. 7. The unit will ask you to test the network connection. Select [OK] and press ENTER ( ) to complete the network connection. 8. If you select [Test]
and press ENTER ( ) at step 7 above, the network connection status is displayed on the screen. You can also test it on the [Connection Status] in the [Setup]
· 3 Installation · · · · · Installation 25 · Any fees charged by an ISP including, without limitation, connection charges are your responsibility. A 10 Base-T or
100 Base-TX LAN port is required for wired connection to this player. If your internet service does not allow for such a connection, you will not be able to
[Wired] and press ENTER ( ). 6.
wireless module, which also supports the 802.
[Setup] menu. Adjust the [NETWORK] setting as follow.
note the SSID and security code of the network. 1.
have 4 keys available on an access point or wireless router's setting.
For details, contact your ISP.
the disc. Some internet contents may require a higher bandwidth connection.
You're reading an excerpt. Click here to read official LG HR500 user
guide
http://yourpdfguides.com/dref/3907575
menu.
connect the unit.
Advertisement
