Page 1
HL-2035 Before you can use the printer, you must set up the hardware and install the driver. Please read this ‘Quick Setup Guide’ for proper set up and installation instructions. STEP 1 Setting Up the Machine STEP 2 Installing the Printer Driver Setup is Complete! How to use the printer, see the User’s Guide on the CD-ROM.
Symbols used in this guide Caution Hot Surface Warning Electrical Hazard Warnings tell you what to do Electrical Hazard icons alert Hot Surface icons warn you Cautions specify procedures to prevent possible personal you to a possible electrical not to touch machine parts you must follow or avoid to injury.
Table of Contents Safety Precautions ............................2 To Use the Printer Safely ........................2 Regulations ............................. 4 Getting Started Carton Components ............................. 6 Control panel..............................7 Printer LED Indications ..........................7 Supplied CD-ROM ............................8 STEP 1— Setting Up the Machine Put the CD-ROM into the CD-ROM drive.....................
Safety Precautions To Use the Printer Safely Warning There are high voltage electrodes inside the printer. Before you clean the inside of the printer, make sure that you have turned off the power switch and unplugged the printer from the AC power outlet. DO NOT handle the plug with wet hands.
Page 5
Safety Precautions DO NOT use flammable substances or any type of spray to clean the inside or outside of the machine. Doing this may cause a fire or electrical shock. Refer to the User's Guide for how to clean the machine.
APPAREIL À LASER DE CLASSE 1 LASER KLASSE 1 PRODUKT Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user's authority This printer has a Class 3B laser diode which to operate the equipment. produces invisible laser radiation in the scanner unit.
Page 7
Safety Precautions Disconnect device You must install this printer near a power outlet that is easily accessible. In case of an emergency, you must disconnect the power cord from the power outlet to shut off the power completely. IT power system (For Norway only) This product is also designed for an IT power system with phase-to-phase voltage 230V.
Getting Started Carton Components Carton components may vary from one country to another. Save all packing materials and the printer carton in case for any reason you must ship your printer. 1 Face-down Output Tray Support Flap (Support Flap) 5 Paper Tray 2 Control panel 6 Power Switch 3 Front Cover...
Getting Started Control panel 1 Toner LED The Toner LED indicates when the toner is low or at the end of its life. 2 Drum LED The Drum LED indicates when the drum is nearing the end of its life. 3 Error LED The Error LED indicates when the printer is in one of the following states:...
Documentation View the Printer User’s Guide in HTML format. You can also view the User’s Guide in PDF format by accessing the Brother Solutions Center. ® The User’s Guide in HTML format will be installed automatically when you install the driver. (For Windows...
STEP 1 Setting Up the Machine Put the CD-ROM into the CD-ROM drive ® ® For Windows users For Macintosh users Improper Setup Improper Setup DO NOT connect the interface cable. DO NOT connect the interface cable. Connecting the interface cable is done when Connecting the interface cable is done when installing the driver.
STEP 1 Setting Up the Machine Put the drum unit and toner cartridge assembly Installing the drum unit and into the printer. toner cartridge assembly Improper Setup DO NOT connect the interface cable. Connecting the interface cable is done when installing the driver.
Setting Up the Machine Put paper in the paper tray. Make sure that the Loading paper in the paper paper is flat in the tray and below the maximum tray paper mark (1). Pull the paper tray completely out of the printer. While pressing the paper-guide release lever (1), slide the paper guides to fit the paper size you are using.
STEP 1 Setting Up the Machine After the printer has finished warming up, the Printing a test page Ready LED stops blinking and stays green. Improper Setup DO NOT connect the interface cable yet. Make sure that the printer power switch is off. Connect the AC power cord to the printer.
Follow the instructions on this page for your operating system and interface. For the latest drivers, documentation, and to find the best solution for your problem, access the Brother Solutions Center directly from the CD-ROM / Driver or visit http://solutions.brother.com.
STEP 2 Installing the Printer Driver ® Windows For USB interface cable users Note Note If the Found New Hardware Wizard appears on ® For Windows Vista , when the User Account your computer, click Cancel. Control screen appears, click Continue. When the License Agreement window appears, click Yes if you agree to the License Agreement.
Page 17
If you want to register your product on-line, check On-Line Registration. ® For Windows 98/Me users: The Setup is now complete. Note Choose the Brother Printer icon. Your HL-2030 series Printer Driver has been installed. Now go to ® For Windows 2000/XP users: Go to ‘Setting Your Printer as the Default...
STEP 2 Installing the Printer Driver ® Macintosh For USB interface cable users ® For Mac OS X 10.2.4 or greater users Click Go, then Applications. ® Connecting the printer to your Macintosh installing the driver Click Install Printer Driver on the menu screen.
Page 19
Installing the Printer Driver ® Macintosh Choose USB. Choose the proper printer, and then click Add. Click Printer Setup Utility, then Quit Printer Setup Utility. The setup is now complete. Note Your HL-2030 series Printer Driver has been installed.
From the Apple menu, click Chooser. Double-click your language folder. Click the Brother Laser icon. On the right side of the Chooser, choose the printer to which you want to print. Close the Chooser. Double-click the Printer Driver Installer icon to install the printer driver.
Consumables When the time comes to replace consumable items, an error will be indicated by the LED’s on the control panel. For more information about the consumables for your printer, visit us at http://solutions.brother.com or contact your local Brother reseller.
Repacking Information Repack the printer. Shipment of the printer If for any reason you must ship your printer, carefully package the printer to avoid any damage during transit. We recommend that you save and use the original packaging. The printer should also be adequately insured with the carrier.
Page 23
The contents of this manual and the specifications of this product are subject to change without notice. Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other errors relating to the publication.