Related Manuals for Maycom FR-100
Summary of Contents for Maycom FR-100
- Page 1 FR-100 MINI HAND HELD TYPE 5 BANDS COMMUNICATIONS RECEIVER USER'S OPERATION MANUAL...
-
Page 2: Table Of Contents
CONTENTS PAGE ■ DESCRIPTION OF FEATURES ............4 -DISPLAY PANEL FEATURES ............. 4 -TOP PANEL FEATURES ..............5 -SIDE AND BACK PANEL FEATURES ..........6 -FRONT PANEL FEATURES ............….. 7 ■ BATTERY PACK INSTRUCTION ............13 ■ SPECIFICATION ................14 Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. -
Page 3: Description Of Features
■ DESCRIPTION OF FEATURES Display Panel Features ● 1. " " Indicates the narrow "FM" mode has been selected. 2. " " Indicates the “AM” mode has been selected. 3. " " Indicates the wide “FM” mode for broadcasting radio has been selected. 4. -
Page 4: Top Panel Features
● Top Panel Features 1. Power On/Off, Volume Turn the Volume switch clockwise to the turn power on and set desired volume. Turn the Volume button anti-clockwise to turn the power off. When the power is on, the lastly used frequency per mode and band is displayed on the LCD. -
Page 5: Side And Back Panel Features
● Side and Back Panel Features 1. MO/SET (Monitor) 1) MO(Monitor) Press the "MO(Monitor)" button shortly in the receiving mode to open the squelch control. This is useful when a weak signal is to be monitored. Re-Activate : Press the MO button one more time. 2) SET To fix each selection. -
Page 6: Front Panel Features
● Front Panel Features 1. ▲(Channel up) button Press the "▲" button to move to a higher frequency than is currently shown on the LCD. To access Up scanning process, press the "▲” button over two seconds. In the event that during the scanning processing, the radio stop for 3 seconds at a receiving frequency and re-starting the scanning processing unless you press any buttons. - Page 7 SQL level will be displayed with S-RF level meter. SQL level will be adjusted from S2 to S8. 3) Change of Frequency step FR-100 has 5KHz,8.33KHz(Air), 10KHz,12.5KHz, 20KHz, 25KHz, 50KHz,100KHz, 200KHz and 1MHz frequency step. To change the frequency step, press the “SEL” button longer than 2 seconds.
- Page 9 When you press the “BAND” button, the last used frequency per band will be displayed on the LCD. 5. MEM button This FR-100 receiver contains a 30 memory locations for each band where desired frequencies can be programmed by the user. 1) Frequency Memory Programming of the desired frequencies memory can be carried out in the following ways.
- Page 10 - Select the frequency which you want by using “SEL,BAND and Frequency Up/Down” button” - Press “MEM” button longer than 2 seconds - The LCD will show the empty memory channel location - Select the memory location where you wish to store the selected frequency by pressing "▲...
- Page 11 6. CUR.(Cursor) button The desired frequency can be directly entered using the cursor function in normal mode. The desired frequency however should be in the allocated frequency range of the band. To enter the frequency directly using cursor function, follow the example: 1) Example of Frequency selection Frequency desired is 145.4650 MHz on the VHF Band.
-
Page 12: Battery Pack Instruction
■ BATTERY PACK INSTRUCTION 1. Press down the battery lock button on the bottom side of the radio.(①) 2. Open the battery cover on the back side of the radio.(②) 3. Install the battery as like shown.(③) 4. Put on the battery cover.(④) 5. -
Page 13: Specification
■ SPECIFICATION 1. GENERAL FREQUENCY ------------------------ A BAND : 66MHz TO 88MHz B BAND : 88MHz TO 108MHz C BAND : 108MHz TO 136MHz D BAND : 136MHz TO 174MHz E BAND : 420MHz TO 470MHz FREQUENCY GENERATION --- PLL SYNTHESIZER FREQUENCY STABILITY -------- +/- 15ppm OPERATING TEMPERATURE -- -10℃...