Advertisement
Quick Links
Installation Instructions
Audio, iPod Interface
SUBJECT
®
IPOD
INTERFACE GEN3 KIT - P/N 65 11 0 035 961
MODEL
X3 (E83):
X5 (E53):
Z4 (E85):
Z4 Coupe (E86):
5-Series (E39):
* Not compatible with 6 Disc CD Changer (SA 672), and vehicle production 09/03 – 09/05 with DSP (SA 677)
and without Navigation.
** Not compatible with optional Navigation (SA609), DSP audio (SA677), and/or 6 Disc CD Changer (SA672).
*** Not compatible with 6 Disc CD changer (SA 672), and vehicle production 10/02 – 02/06 with DSP (SA 677)
and without Navigation.
**** Not compatible with 6 Disc CD changer.
SUGGESTED INSTALLATION TIME:
Total installation time may vary depending on vehicle options and equipment.
The instructions below are developed for BMW vehicles and are not to be compared to any other existing
instructions for vehicles other than BMW. No methods other than those specified in this document are to be
used for installation in BMW vehicles. Left and right are determined from the driver's seat.
Carefully read all instructions and supplements before proceeding with the installation. Reference should be
made to TIS for instructions dealing with a stock part of the vehicle but not stated in detail in these instructions.
The instructions were complete and up to date at time of publication; however, changes to the vehicle or
installation may have occurred. Please report any problems or changes noted with the installation to BMW
Technical Hotline, along with VIN, date of manufacture and as much detail as possible.
DO IT RIGHT THE FIRST TIME, ON TIME, EVERY TIME
Installation Instruction P/N 01 29 0 440 076
2007 BMW of North America, LLC
Select Vehicle Production 09/03 – On*
Select Vehicle Production 10/00 – On**
Select Vehicle Production 10/02 – On***
Select Vehicle Production 05/06 – On****
Select Vehicle Production 9/00 – 8/03**
0.75 Hours
Page 1 of 19
October 2007
Ver 1.0
Accessory
Development
Advertisement
Related Manuals for BMW 65 11 0 035 961
Summary of Contents for BMW 65 11 0 035 961
-
Page 1: Installation Instructions
Total installation time may vary depending on vehicle options and equipment. The instructions below are developed for BMW vehicles and are not to be compared to any other existing instructions for vehicles other than BMW. No methods other than those specified in this document are to be used for installation in BMW vehicles. -
Page 2: Parts Information
PARTS INFORMATION Contents of Kit – P/N 65 11 0 035 961 Description BMW Part Number iPod I/F module 65 11 0 035 962 iPod I/F Gen3 cable 65 11 0 035 957 Radio I/F cable 65 11 0 411 924... - Page 3 Vehicle Preparation (for all vehicle models) Only for vehicles equipped with the 6 Disc CD Changer: 1. Remove 3-pin connector (X18180) and 6-pin connector (X9960) from 6 Disc CD changer. Warning: Failure to perform this step will cause the iPod Interface to malfunction. Installation Instruction P/N 01 29 0 440 076...
- Page 4 Procedure for X3 1. Disconnect vehicle battery. 2. Remove the following components using procedures available through TIS: • Center vent (1) • Radio (2) • Climate Control (3) • Glove box (4) 3. Remove the blue lock (1) from radio harness by releasing tab and sliding upwards, then remove following terminals (2) using AMP terminal removal tool (p/n...
- Page 5 7. Insert white 12-pin connector (1) from iPod harness (2) into lower left section of radio connector (3). 8. Tie original white 12-pin connector (4) back to harness. 9. Connect 4-pin connectors (1 & 2) 10. Locate and drill 5/8” (16mm) hole in glovebox.
- Page 6 12. Split grommet (1) as indicated (2) and insert grommet through hole in glovebox wall. 13. Secure grommet to glovebox with weatherstrip adhesive from the outside of the glovebox. 14. Route iPod cable through center console from radio location to glovebox location. 15.
- Page 7 Procedure for Z4 Roadster and Coupe 1. Disconnect vehicle battery 2. Remove the following components using instructions available through TIS: • Center vent (1) (REF #64 22 161) • Radio (2) (REF #65 11 080) • Glove box door (3) 3.
- Page 8 7. Insert white 12-pin connector (1) from iPod harness (2) into lower left section of radio connector (3). 8. Tie original white 12-pin connector (4) back to harness. 9. Connect 4-pin connectors (1 & 2) 10. Locate and drill 5/8” (16mm) hole in glove box upper right panel.
- Page 9 12. Split grommet (1) as indicated (2) and insert grommet through hole in glovebox wall. Caution: Check for bent pins on adapter cables before attaching to iPod module. If pins are damaged carefully bend them back into position with a small screwdriver.
- Page 10 Procedure for X5 (E53) 1. Disconnect vehicle battery. 2. Remove the following components using procedures available through TIS: • Radio (1) • Glovebox (2) 3. Remove the blue lock (1) from radio harness by releasing tab and sliding upwards, then remove following terminals (2) using AMP terminal removal tool (p/n 611134): Pin #...
- Page 11 7. Insert white 12-pin connector (1) from iPod harness (2) into lower left section of radio connector (3). 8. Tie original white 12-pin connector (4) back to harness. 9. Connect 4-pin connectors (1 & 2) 10. Locate and drill 5/8” (16mm) hole in glove box.
- Page 12 12. Split grommet (1) as indicated (2) and insert grommet through hole in glovebox wall. 13. Secure grommet to glovebox with weatherstrip adhesive from the outside of the glovebox. 14. Route iPod cable through center console from radio location to glovebox location. 15.
- Page 13 Procedure for 5 Series (E39) 1. Disconnect vehicle battery. 2. Remove the following components using procedures available through TIS: • Radio (1) • Glove box (2) 3. Remove glovebox side panel by first removing 2 screws. 4. Remove the blue lock (1) from radio harness by releasing tab and sliding upwards, then remove following terminals (2) using AMP terminal removal tool (p/n...
- Page 14 6. Insert 3 rectangular pins from iPod harness (1) into radio harness (2) as follows: Color Location Description WS/GR/GE I-Bus KL 31 RT/GN KL 30 7. Remove white 12-pin connector (3) from lower section of radio connector. 8. Insert white 12-pin connector (1) from iPod harness (2) into lower left section of radio connector (3).
- Page 15 12. Insert iPod cable (1) through hole in glove box as indicated. 13. Split grommet (1) as indicated (2) and insert grommet through hole in glovebox wall. 14. Secure grommet to glovebox with weatherstrip adhesive from the outside of the glovebox. 15.
- Page 16 18. Mount iPod I/F module as indicated below radio. Secure with cable ties if possible. 19. Reinstall all components removed for installation procedure. Installation Complete Installation Instruction P/N 01 29 0 440 076...
- Page 17 RETROFIT CODING There is no retrofit coding required for this installation except for the following vehicles: X3 (E83) with DSP and without Navi: Vehicle Production 09/05 – On Z4 (E85) with DSP and without Navi: Vehicle Production 02/06 – On Z4 Coupe (E86) with DSP and without Navi: Vehicle Production 05/06 –...
-
Page 18: Troubleshooting
SW 1.1.1 If the customer’s iPod has older versions of software, please advise them to upgrade the software before connecting them to the Interface in their BMW vehicles (refer to BMW iPod Interface Owner’s Manual). • In case of erratic behavior in iPod mode please perform the following: RESET the iPod –... - Page 19 Circuit Diagram Connection, radio (audio signal) Connection, MPQ contacts X-3A Connection, 4-pin Connection, Fuse (2A) Connection, 7-Pin DIN connector Wire Colors Blue Brown Yellow Green Gray Black Violet White Installation Instruction P/N 01 29 0 440 076...
Need help?
Do you have a question about the 65 11 0 035 961 and is the answer not in the manual?
Questions and answers