1. Manuals
  2. Brands
  3. Smartview Manuals
  4. Magnifiers
  5. TX
  6. User manual

Smartview TX User Manual

Electronic magnifying system
Hide thumbs
Table of Contents

Advertisement

Quick Links

SMARTVIEW
USER'S MANUAL
Copyright © 1994, 1999 by Pulse Data International Limited,
Christchurch, New Zealand. All rights reserved. No part of this
publication may be reproduced or distributed in any form or by
any means, or stored in a database or retrieval system, without
the prior written permission of Pulse Data International Limited.
Every effort has been made to ensure that the information
contained in this publication is correct at the time of issue.
Neither Pulse Data International Limited, nor its agents, assume
any responsibility for errors or omissions.
assumed for damages resulting from the use of the information
contained herein.
PULSE DATA
INTERNATIONAL LIMITED
support@pulsedata.com
Internet
www.pulsedata.com
Model TX
1 Expo Place
P.O. Box 3044, Christchurch, New
Zealand
Telephone +64 3 3844555
Fax
E-mail
1-i
Nor is any liability
+64 3 3844933

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TX and is the answer not in the manual?

Questions and answers

Summary of Contents for Smartview TX

  • Page 1 SMARTVIEW Model TX USER'S MANUAL Copyright © 1994, 1999 by Pulse Data International Limited, Christchurch, New Zealand. All rights reserved. No part of this publication may be reproduced or distributed in any form or by any means, or stored in a database or retrieval system, without the prior written permission of Pulse Data International Limited.
  • Page 2 IMPORTANT SAFETY INSTRUCTIONS 1) Follow all warnings, cautions and instruction marked on the product. 2) The power supply cord serves as a disconnect device for pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 3) This product is equipped with a 3-wire grounding type plug, a plug having a third (grounding) pin.
  • Page 3 Refer all servicing to qualified service personnel. SUSCEPTIBILITY TO INTERFERENCE There may be temporary degradation of the image when the SmartView is subjected to a strong radio-frequency field, electro-static discharge or transient electrical noise. FCC WARNING (USA only) This equipment generates and uses radio frequency...
  • Page 4 interference by one or more of the following measures: (1) Reorient the receiving antenna. (2) Relocate the equipment with respect to receiver. (3) Move the equipment away from the receiver. (4) Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.
  • Page 5 This Class digital apparatus meets requirements of the Canadian Interference-Causing Equipment regulations.

  • Page 6: Table Of Contents

    TABLE OF CONTENTS 1. INTRODUCTION ..... 2. SETTING UP ......3.
  • Page 7 SMARTVIEW 1-vii...

  • Page 8: Introduction

    Locate the AC power cable supplied with the SmartView and plug it into the socket labeled "INPUT POWER" on the back of the reader unit. Plug the other end into a wall socket.
  • Page 9 TO AC WALL SOCKET SmartView rear panel Switch on SmartView with the on-off switch on the right-hand side of the main pillar. The fluorescent lamps over the reading table will light up. Put some suitable material, such as this manual, on the SmartView reading table under the lamps.

  • Page 10: Controls

    wish to increase the brightness and contrast with the TV controls. CONTROLS Size and Focus There are two large knobs on the front of the unit. The right-hand one adjusts the FOCUS, while the left-hand SIZE knob changes the magnification. SIZE PICTURE FOCUS...

  • Page 11: Line Marker

    Line Marker A line marker is a horizontal line which can be made to appear approximately a third of the way up the screen. It can be used as a reading guide by positioning the reading table so that the line marker is just above or just below the line of text being read.

  • Page 12: The "Text/Photo" Switch

    If you prefer not to use the line marker then turn the PICTURE knob one turn anticlockwise. Normal text is black-on-white. If you prefer to read white-on-black, turn the PICTURE knob fully anti- clockwise. When the knob is turned fully anticlockwise the line marker will appear.

  • Page 13: Reading A Document

    For the smallest possible magnification, slide the knob fully towards the back of the unit. For the greatest possible magnification, slide it to the front. READING A DOCUMENT To read a document, set the Size control for the smallest magnification that allows characters to be comfortably and clearly seen.

  • Page 14: Trouble Shooting

    If there is no picture Check that the AC cables are plugged in properly. Ensure that the power is switched on at the wall socket, and that the switch on the SmartView is turned on. The power indicator on the TV set should be glowing, and the fluorescent lamps should be alight.

  • Page 15: If The Image Is Unclear

    Turn the Picture knob to increase contrast. Check that both the fluorescent lamps are fully alight. RETURNING FOR SERVICE If you have a problem with SmartView, call your service agent and discuss the fault (have your SmartView nearby). If the problem cannot be fixed by phone, send the SmartView to the service agent, with a letter detailing the problem.
  • Page 16 1-10...

Table of Contents