Download
Share
Print this page
  1. Manuals
  2. Brands
  3. AOLYNK Manuals
  4. Wireless Router
  5. DR814Q
  6. Quick start manual

AOLYNK DR814Q Quick Start Manual

Adsl2+ broadband router
Hide thumbs
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
Aolynk DR814Q ADSL2+ Broadband Router
1 Packing List
Unpack the shipping carton carefully and check the following items listed below:
One Aolynk DR814Q ADSL2+ Broadband Router
One power adapter
One telephone cable
One Ethernet cable
One USB cable
Two sets of screws and anchors
Aolynk DR814Q ADSL2+ Broadband Router Quick Start
CD including a user manual and a driver
Certificate of Quality
Warranty Card
If anything is broken or missing, contact your agent for help.
2 Installation
2.1 Installation Precautions
Use the DR814Q indoors and keep it far away from the heat sources and water/liquid.
Keep the cabinet or desk stable enough to hold the DR814Q. Fix the DR814Q and
power adapter well on the wall when wall-mounting it.
Reserve more than 10 cm (4 in.) of clearance around the DR814Q chassis for heat
dissipation.
Wire the port cable indoors. Outdoor cabling is prohibited, to prevent the signal port
from damages that may be caused by overvoltage and overcurrent from lightning
strike.
2.2 Device Connection
I. Connect to an ADSL line
To connect to an ADSL line, you have two options:
Connect one end of the telephone cable to the ADSL port on the DR814Q rear panel,
and the other end to the telephone jack on the wall.
As shown in Figure 1, connect the ADSL port of the DR814Q to a splitter via the
telephone cable and a telephone to the splitter, too. Then, connect the splitter to
the telephone jack on the wall. In this option, you can use the telephone and
access the network at the same time.
Quick Start
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the DR814Q and is the answer not in the manual?

Questions and answers

Summary of Contents for AOLYNK DR814Q

  • Page 1 As shown in Figure 1, connect the ADSL port of the DR814Q to a splitter via the telephone cable and a telephone to the splitter, too. Then, connect the splitter to the telephone jack on the wall.
  • Page 2 1 through LAN 4). III. Connect to the power adapter (1) Attach one end of the included power adapter to the DR814Q and the other end to the power socket. (2) Approximately one minute after the power-on of the DR814Q, the states of the LEDs on the front panel should be those listed in Table 1.

  • Page 3: Prerequisite Tasks

    Web configuration page. Figure 2 Type in the username and password Note: 1. The DR814Q provides the automatic dialing function, thus the dialing software (PPPoE dialing software, for example) provided by the operation system or other client dialing software is not needed and can be uninstalled.
  • Page 4 I. Set parameters Click [Quick Setup] in the navigation bar to enter the corresponding page. To access a network by PPPoE dial-up connection: Select the PPPoE option, type in the VPI/VCI value, the username and password required for the dial-up connection which are provided by your ISP, and then click <Apply>.
  • Page 5 Note: You can consult your local ISP for the VPI/VCI value, the username and password required for the configuration. II. Display IP address of the WAN port on the DR814Q After a while, click [Status] in the navigation bar to enter the [Status] page. A new public IP address for the WAN IP Address item has replaced the previous 0.0.0.0, indicating that...

  • Page 6: Quick Troubleshooting

    The Ethernet cable is connected to the port correctly. The used Ethernet cable is in good condition: Connect two ends of the cable to the LAN ports of the DR814Q The LAN LED is OFF. respectively, and observe whether the corresponding LEDs turn on.