Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Polsen ULW-16
Summary of Contents for Polsen ULW-16
- Page 1 16-CHANNEL ABLE UHF CAMERA-MOUNT WIRELESS SYSTEM PRODUCT MANUAL...
-
Page 2: Introduction
The ULW-16 system includes a transmitter that features a variable-level control that lets you adjust the transmission level. It’s also equipped with a line input that enables the transmission of such devices as an audio mixer. -
Page 3: Table Of Contents
Mounting ..........11-12 interference than VHF systems and greater reliability at longer distances. Operating in this bandwidth also ensures that the ULW-16 and ULW-16-HL systems are “future Stage Direction and Talent Cueing ..13 proof” and meet current and known future FCC regulations. -
Page 4: Overview
O V E R V I E W Transmitter Receiver... - Page 5 Receiver Transmitter Level control Headphone-level control RF LED TX LED Headphone output Microphone input Antenna Antenna Audio output (line level) Line-level input Channel indicator LED Channel indicator LED Channel up/down buttons Channel up/down buttons Battery compartment panel Battery compartment panel Locking wheel Belt clip Mounting foot...
-
Page 6: Precautions
P R E C A U T I O N S Handheld Transmitter • Exposure to high sound levels can cause Grille and windscreen permanent hearing loss. Avoid listening at high Mic capsule Anti-roll ring volumes for extended periods of time. LCD display •... -
Page 7: Installing Batteries
4. Close the panel completely so it locks into place. Tip: You can use rechargeable AA batteries with the receiver and transmitter and recharge them by inserting them into the Polsen ULW-BBCH charger (sold separately). Use only rechargeable batteries with the charger. Do not attempt to charge standard batteries –... -
Page 8: Operating Instructions
3. Use the channel selector buttons to set the transmitter and receiver to the same channel. If you are experiencing interference or noise on one channel, try a different channel. If you are using multiple ULW-16 wireless systems, make sure each system is set... - Page 9 2. Set the handheld transmitter and the receiver to the same channel. If you are experiencing interference or noise on one channel, try a different channel. To select the channel on the ULW-16-HHT, follow these steps: a. Remove the battery compartment cover.
- Page 10 10 seconds and then stop indicating that the channel has been selected. d. Replace the battery compartment cover. Note: If you are using multiple ULW-16 or ULW-16-HL wireless systems, make sure each system is set to a different channel—at least three channels apart as a guard band.
-
Page 11: Mounting
M O U N T I N G Once you have determined that the transmission quality and level are good, mount the receiver and transmitter. Receiver 1. Loosen the receiver’s locking wheel and slide the mounting foot all the way into your camera’s shoe. - Page 12 Transmitter (ULW-16 only) 1. Use the integrated belt clip to secure the transmitter to your talent. Use the included tie clip to place the microphone on your talent. 2. If you are connecting to a line-level source, use an appropriate cable to connect to the mono 3.5 mm jack.
-
Page 13: Stage Direction And Talent Cueing
S TA G E D I R E C T I O N A N D TA L E N T C U E I N G The ULW-16 can also be used as an impromptu one-way voice communication system for stage directions and talent cueing. In this case, your talent will operate the receiver instead of the transmitter, and monitor via an earphone (not included) plugged into the headphone output. -
Page 14: Troubleshooting
Because of the widespread use of wireless technology, many RF signals pervade our environment. This can sometimes make it challenging to work with a wireless system like the ULW-16. In some cases, you may be doing everything correctly and still be experiencing some difficulties. - Page 15 If there are obstructions you may need to move closer. When using the ULW-16-HHT handheld transmitter, make sure you’re holding it in the middle of the body and that your hand isn’t covering the antenna, located at the end of the transmitter.
- Page 16 Problem Possible Cause Solution Comment The audio The batteries are Replace the batteries in the receiver and transmitter Make sure to bring extra batteries with you. is noisy or weak. or handheld transmitter. You should replace the batteries on every shoot. distorted.
- Page 17 Approximately 6" (15.2 cm) from the subject is ambience is omnidirectional the subject. usually good microphone placement, but you may being picked up. microphone like need to experiment. the PL-4 or PL-5 included with the ULW-16 system, the microphone may be picking up too much ambience.
-
Page 18: Specifications
S P E C I F I C AT I O N S Transmitter F R E Q U E N C Y R E S P O N S E 60 Hz to 18 kHz System R F O U T P U T P O W E R 10 mW S P U R I O U S R E J E C T I O N >55 dBc F R E Q U E N C Y R A N G E 584.400 to 602.450 MHz M A X I M U M I N P U T V O LTA G E 1,000 mV... -
Page 19: Handheld Transmitter
PL-4 Microphone PL-5 Microphone Handheld Transmitter T R A N S D U C E R Back electret condenser T R A N S D U C E R Back electret condenser T R A N S D U C E R Dynamic P O L A R PAT T E R N Omnidirectional P O L A R PAT T E R N Omnidirectional P O L A R PAT T E R N Cardioid (Unidirectional) -
Page 20: One-Year Limited Warranty
To obtain warranty coverage, contact the Polsen Customer Service Department to obtain a return merchandise authorization (“RMA”) number, and return the defective product to Polsen along with the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own risk and expense.
Need help?
Do you have a question about the ULW-16 and is the answer not in the manual?
Questions and answers