Summary of Contents for impro ImproX KHR XKR-901-1-0-GB-01
- Page 1 IMPROX Harsh Environment Remote Reader INSTALLATION MANUAL MODEL: XKR-901-1-0-GB-XX Manual reference number : XKR300-0-0-GB-04 Issue 5 July 2002...
- Page 2 As Impro Technologies (Pty) Ltd has no control over where the product is used, or how it is installed, no liability for ANY consequential damages can be accepted, whether due to malfunction, design, deficiency, implementation or any cause whatsoever.
- Page 3 No. 1016 impro-jpAdb3.so-net.ne.jp Yokohama Address : IMPRO UK Unit 13 Tel: 01442 281644 Sovereign Park Fax: 01442 281645 Cleveland Way E-mail : Hemel Hempstead sales@improuk.com Herts HP2 7DA Data subject to change without notice © uly 2002 Impro Technologies Page 3...
- Page 4 Data subject to change without notice © July 2002 Impro Technologies Page 4...
-
Page 5: Table Of Contents
Figure 1 : Minimum distance between Remote Readers .........10 Figure 2 : Bottom cable exit .................11 Figure 3 : Install Backing plate................12 Figure 4 : Terminal block cable connections ............13 Data subject to change without notice © July 2002 Impro Technologies Page 5... - Page 6 TABLES Table 1: Tag Read/Write Range ................9 Table 2: Table of Standards .................. 9 Data subject to change without notice © July 2002 Impro Technologies Page 6...
-
Page 7: Introduction
C (-13 F to +176 Storage C to +80 C (-40 F to +176 HUMIDITY RANGE 0 to 95% relative humidity at +40 C (+104 non-condensing. EN 55024. Data subject to change without notice © July 2002 Impro Technologies Page 7... -
Page 8: Electrical Specifications
The range at which the Remote Reader can read to or write from a tag is dependent on the type of tag and on the material on which a particular reader is mounted. Typical ranges are shown in Table 1 below. Data subject to change without notice © July 2002 Impro Technologies Page 8... -
Page 9: International Standards
Measurement Techniques. Section 3: Radiated, Radio-Frequency, Electromagnetic Field Immunity Test. EN 61000-4-6 Conducted Susceptibility. EN 61000-4-5 Surge Immunity. EN 61000-4-11 Voltage Dips and Interruptions. Table 2 : Table of Standards/Specifications Data subject to change without notice © July 2002 Impro Technologies Page 9... -
Page 10: Approvals
Figure 1. Minimum distance 500 mm Minimum distance 500 mm khr distances.wmf Figure 1 : Minimum distance between Remote Readers Data subject to change without notice © July 2002 Impro Technologies Page 10... -
Page 11: Location Of The Khr Remote Reader
Figure 2 : Bottom cable exit INSTALLING THE BACKING PLATE General The KHR Remote Reader backing plate includes four mounting holes and one central cable exit hole (see Figure 3). Data subject to change without notice © July 2002 Impro Technologies Page 11... -
Page 12: Mounting On A Concrete Or Brick Wall
[3] If required, drill the centre hole through the wood [for the cable] using a 5 mm diameter [minimum] drill bit. [4] Secure the backing plate to the surface using the four mounting screws provided. Data subject to change without notice © July 2002 Impro Technologies Page 12... -
Page 13: Mounting On Metal
[3] Push the unit front cover towards the backing plate until it is in position. [4] Insert the locking screw through the cover into the backing plate, and tighten it. Data subject to change without notice © July 2002 Impro Technologies Page 13... -
Page 14: Electrical Connections
The ImproX KHR Remote Reader is designed to be used in conjunction with the ImproX DT Door Terminal or the ImproX PT Portal Terminal. ORDERING INFORMATION The ImproX KHR Remote Reader can be ordered separately under the Impro code XKR901-1-0-GB-XX or with an ImproX PT Portal Terminal under the Impro code XPT900-1-0-GB-XX. - Page 15 USER NOTES Data subject to change without notice © July 2002 Impro Technologies Page 15...
- Page 16 NOTES APPLICABILITY OF THIS MANUAL The last two digits of the standard Impro stock code indicate the issue status of the item concerned. This manual is applicable to the Improx KHR Keypad Remote XKR-901-1-0-GB-01 onwards. The next issue of this manual will determine the final equipment issue to which this issue is applicable.