Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Fein RB30
- Page 1 RB30 Microscope User’s Manual info@feinoptic.com...
-
Page 2: Microscope Components
Microscope Components: Page 1 info@feinoptic.com... -
Page 3: Before Use
The power switch (4) is located on the side of the base of the microscope. Microscope uses 3.3V 3W LED bulb, part # RB30-001. Voltage range of 100~240V is supported. Additional transformer is not necessary. Use only an outlet with voltage in this range and use the power cord supplied with the microscope. -
Page 4: Maintenance
Do not disassemble the microscope. After use, cover the microscope with a dust cover and power o the light. Objectives: RB30 In nity Corrected Objectives all have a parfocal distance of 45mm. Recommended coverslip thickness is 0.17mm. Numerical Aperture Working Distance... - Page 5 Binocular / Trinocular Microscope Assembly: Page 4 info@feinoptic.com...
- Page 6 Fluorescence Microscope Assembly: Page 5 info@feinoptic.com...
- Page 7 Step-by-Step Assembly: Condenser Assembly: Rotate the coarse focus knob (1) to raise the stage to its highest position. Rotate the condenser lowering knob (2) to lower the condenser bracket. Loosen the condenser lock screw (3). Insert the condenser and tighten the lock screw. Raise the condenser back to the highest position.
- Page 8 Step-by-Step Assembly: Power Cord Connection: Set the power switch to “O” o before connecting the power cord. Insert the connector (1) into the power socket (2). Insert the plug into the power supply. Voltage range 100~240V supported. Connect power and make sure the instrument is grounded.
- Page 9 Step-by-Step Assembly: Adjusting Focus Tension: If it becomes hard to move the coarse focus knob, or the stage drifts and the sample falls out of focus the tension needs to be adjusted. Tighten the tension by adjusting the tension adjustment ring (1) in the direction of the arrow shown at right.
- Page 10 After use, wipe the lens with a tissue moistened with microscope cleaning solution. Using Filters: Filters can increase the contrast in microscopy images. The lter sits on top of the light as shown at right. The RB30 accepts a 45mm diamter lter. Page 9 info@feinoptic.com...
- Page 11 Step-by-Step Assembly: Replacing the Fuse: Turn the power switch to “O” o . Remove the power cord. Unscrew the fuse group (1) from the base (2) with a athead screwdriver. Install a T250V, 3.15A fuse. C-Mount Assembly: Loosen the trinocular head set screw (1) and remove the trinocular port dust cap (2).
- Page 12 Full Phase Contrast / Polarization Assembly: Phase Contrast Condenser Assembly: Install phase contrast objective lenses. Insert the condenser into the holder and tighten set screw. Rotate the phase adjustment ring (2) to “BF” (bright eld) until it clicks into place. Focus on a sample to ensure condenser is installed straight.
- Page 13 Fluorescence Light Assembly: Installing the Fluorescence Illuminator: Place the uorescence module (2) on the microscope body and tighten the set screw. Place the binocular / trinocular head on top of the uorescence module and tighten the set screw (3). Insert transformer (1) into socket (2) and then plug directly into outlet.
-
Page 14: Troubleshooting
Use the same eyepieces in each Di erent eyepieces are being used in the match with the left. eyetube. Use the Fein Optic left and right eyetube. FPL-WF10x/22 Eyepieces. Page 13 info@feinoptic.com... - Page 15 Troubleshooting: Mechanical & Electrical Troubleshooting Problem Cause Solution The cover glass is not facing up. Put the cover glass face up. Can not get the objective lens to focus. Use cover glass thickness The cover glass is not standard thickness. 0.17mm.
-
Page 16: Bulb Replacement
5. Rescrew the bulb assembly back onto the bulb holder compartment. 6. Reinsert the bulb holder back into the microscope. 7. Power the microscope on and turn on the light. RB30-001 Replacement LED Bulb Assembly Page 15 info@feinoptic.com...