Related Manuals for Professional Entertainment Technology BEAM-2R/PRO
Summary of Contents for Professional Entertainment Technology BEAM-2R/PRO
-
Page 1: User Manual
BEAM-2R/PRO Professional Beam Moving Head User Manual Professional Entertainment Technology Please read these instructions carefully before use... -
Page 3: Table Of Contents
TABLE OF CONTENTS 1. Safety Instructions .....................2 2. Technical Specifications....................4 3. Description .......................5 3.1 Control Panel ....................5 4. Gobo and Lamp ......................6 4.1 Gobo .........................6 4.2 Lamp.........................7 4.3 Change the Lamp....................7 5. How To Set The Unit ....................9 5.1 Main Function ....................9 5.2 Home Position Adjustment................19 5.3 Error Information....................21 6. Control By Universal DMX Controller ..............22 6.1 Connection .....................22 6.2 Channel Mode Setting ..................23 6.3 Address Setting....................23 6.4 DMX 512 Configuration ..................24 7. Troubleshooting......................27 8. Maintenance and Cleaning..................29 ... -
Page 4: Safety Instructions
1. Safety Instructions Please read carefully the instruction manual, which includes important information about the installation, usage and maintenance. WARNING Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction manual. Important: Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems. Unpack and check carefully that there is no transportation damage before using the unit. The unit is for indoor use only. Use only in a dry location. Do install and operate by qualified operator. Do not allow children to operate the fixture. Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only. The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure that no ventilation slots are blocked; otherwise the unit will be overheated. Before operating, ensure that the voltage and frequency of power supply matches the power requirements of the unit. It’s important to ground the yellow/green conductor to earth in order to avoid electric shock. Maximum ambient temperature TA: 40℃. Don’t operate it when the temperature is higher. Don’t connect the device to any dimmer pack. During initial start‐up some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective, and it will decrease gradually within 15 minutes. ... - Page 5 Do not operate in dirty or dusty environment; do clean the fixture regularly. Do not touch any wire during operation as there might be a hazard of electric shock. Avoid power wires twist other cables. The minimum distance between light output and the illuminated surface must be more than 12 meters. Disconnect mains power before fuse/lamp replacement or servicing. Replace fuse/lamp only with the same type. In the event of serious operating problem, stop using the unit immediately. Never turn on and off the unit time after time. The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged. Do not open the unit as there are no user serviceable parts inside. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center if needed. ...
-
Page 6: Technical Specifications
2. Technical Specifications DMX Channels: 14&16 channels Smooth 0~100% dimming and variable strobe speeds Motorized focus by DMX control Automatic Pan/Tilt position correction Excellent ventilation, ensuring reliable operation Voltage: AC 100~240V, 50/60Hz Power Consumption: 250W Lamp: PHILIPS MSD Platinum 2R, about 6000hrs Beam Angle: 3° Dimension: 311 x 256 x 476mm Weight: 15Kgs ... -
Page 7: Description
3. Description 3.1 Control Panel 1. Display: Show the various menus and the selected functions; 2. LED: POWER On Power On DMX On DMX input present 3. Button: MENU To enter into, move backward or leave the menu Move up in the menu Move down in the menu ENTER Enter the desired functions 4. DMX IN: For DMX 512 operation, use 3/5‐pin XLR plug cable to link the units together; 5. DMX OUT: For DMX 512 operation, use 3/5‐pin XLR plug cable to link the units together 6. POWER IN: For connection to a socket (100~240V, 50/60Hz) via the supplied mains cable. ... -
Page 8: Gobo And Lamp
7. POWER OUT: Connect to supply power to the next unit. 8. Fuse (T 6.3 A): Protect the unit from damage of over current. 4. Gobo and Lamp 4.1 Gobo DANGER! Install/change the gobo‐wheel with the device switched off only. ... -
Page 9: Lamp
4.2 Lamp Philips MSD Platinum 2R Because of its high internal pressure, there might be a risk that the Discharge lamp would explode during operation. The lamp emits intense UV radiation which is harmful to the eyes and skin. The high luminance of the arc can cause severe damage to the retina if you take a close look at the lamp. To protect the lamp, always turn off the lamp first (via control panel or DMX controller) and let the unit run at least five minutes to cool down before switching off the mains supply. Never handle the lamp or luminary when it is hot. ... - Page 10 Fig.2 Use 1/4 Turn loosen the screws and take out the fan. Fig.3 Take away the old lamp. Fig.4 Unplug all the connect wires over the lamp and wear anti‐static gloves to take on the lamp. And then change a new lamp. ...
-
Page 11: How To Set The Unit
5. How To Set The Unit 5.1 Main Function Turn on the unit, press MENU button into menu mode, press UP and DOWN button until the required function is shown on the monitor. Select the function by ENTER button. Use UP and DOWN button to choose the submenu, press the ENTER button to store and automatically return to the last menu. Press MENU button or let the unit idle one minute to exit menu mode. ... - Page 13 DMX Functions Enter menu mode, select DMX Functions, press ENTER button to confirm, use UP and DOWN button to select DMX Address, DMX Channel Mode or View DMX Value DMX Address ‐ DMX512 address setting Select DMX Address, press ENTER button to confirm, the present address will blink on the display, use UP and DOWN button to adjust the address from 1 to 512, press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. DMX Channel Mode ‐ channel mode Select DMX Channel Mode, press ENTER button to confirm, present channel mode will blink on the display, use UP and DOWN button to select Mode 1 (16) or Mode 2 (14), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. ...
- Page 14 View DMX Value Select View DMX Value, press ENTER button to confirm. Channel function and its value will show on the display, use UP and DOWN button to view other DMX value. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. Fixture Setting Enter menu mode, select Fixture Setting, press ENTER button to confirm, use UP and DOWN button to select Pan Inverse, Tile Inverse, P/T Feedback, BL.O. P/T Moving, BL.O. Color Change or BL.O. Gobo Change. Pan Inverse Select Pan Inverse, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select No (normal) or Yes (pan inverse), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. Tilt Inverse Select Tilt Inverse, press ENTER button to confirm, present mode will blink on the display, use ...
- Page 15 BL.O. Color Change ‐ Blackout while change color Select BL.O. Color Change, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select No (normal while change color) or Yes (blackout while change color), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. BL.O. Gobo Change ‐ Blackout while change gobo Select BL.O. Gobo Change, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select No (normal while changing gobo) or Yes (blackout while changing gobo), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. Lamp Setting Enter menu mode, select Fixture Setting, press ENTER button to confirm, use UP and DOWN button ...
- Page 16 (When you operate the unit via DMX controller, set the value of channel “special function” to “lamp off”, waiting for 5 seconds, then the lamp will be off if you choose “yes” mode). On If DMX On ‐ Lamp turns on when DMX signal is detected Select On If DMX On, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select Yes (Lamp turns on when DMX signal is detected) or No (keep the present state), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode (If the lamp is off via DMX signal, you can reconnect the DMX controller to make the lamp on). Off If DMX Off ‐ Lamp turns off when DMX signal is cut off Select Off If DMX Off, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select Yes (Lamp turns off when DMX signal is cut off), press ENTER ...
- Page 17 Display Inverse Select Display Inverse, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select No (normal display) or Yes (inverse display), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. Backlight Auto Off Select Backlight Auto Off, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select No (display always on) or Yes (display goes off one minute after exiting menu mode), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. Backlight Intensity Select Backlight Intensity, press ENTER button to confirm, present mode will blink on the display, ...
- Page 18 Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. Language Select Language, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select English or Chinese, press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. Fixture Test Enter menu mode, select Fixture Test, press ENTER button to confirm, use UP and DOWN button to select Auto Test or Manual Test Auto Test Select Auto Test, press ENTER button to confirm, the unit will run built‐in programs to automatically test pan, tilt, color, gobo, gobo rotation, shutter, dimmer, prism, prism rotation, focus, and lamp on/off. . Press MENU button back to the last menu or exit menu mode after auto test. ...
- Page 19 Lamp On time Select Lamp On time, press ENTER button to confirm, lamp on time will show on the display, press ENTER button to confirm, use UP and DOWN button to select Exit or Reset Time, press ENTER button to confirm. Press MENU button back to the last menu or exit menu mode let the unit idle one minute. Firmware Version Select Firmware Version, press ENTER button to confirm, firmware version will show on the display, press MENU button back to exit. Reset Functions Enter menu mode, select Reset Function, press ENTER button to confirm, use UP and DOWN button to select Pan/Tilt, Shutter/Prism, Color, Gobo, Focus or All. Pan/Tilt ‐ Reset Pan/Tilt Select Pan/Tilt, press ENTER button to confirm, use UP and DOWN button to select Yes (the unit will run built‐in program to reset pan and tilt to their home positions) or No, press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. Shutter/Prism ‐ Reset Shutter/ Prism Select Shutter/Prism, press ENTER button to confirm, use UP and DOWN button to select Yes (the unit will run built‐in program to reset shutter and prism to their home positions) or No, press ENTER button to store. Press MENU button to exit. Color ‐ Reset Color Select Color, press ENTER button to confirm, use UP and DOWN button to select Yes (the unit will run built‐in program to reset color to their home positions) or No, press ENTER button to store. Press MENU button to exit. Gobo ‐ Reset Gobo Select Gobo, press ENTER button to confirm, use UP and DOWN button to select Yes (the unit will run built‐in program to reset GOBO wheel to their home positions) or No, press ENTER ...
- Page 20 button to store. Press MENU button to exit. Focus ‐ Reset Focus Select Focus, press ENTER button to confirm, use UP and DOWN button to select Yes (the unit will run built‐in program to reset Focus to their home positions) or No, and press ENTER button to store. Press MENU button to exit All ‐ Reset All Select All, press ENTER button to confirm, use UP and DOWN button to select Yes (the unit will run built‐in program to reset all motors to their home positions) or No, press ENTER button to store. Press MENU button to exit. Special Functions Enter menu mode, select Special Functions, press ENTER button to confirm, select Fixture Maintenance or Factory Setting. Fixture Maintenance Select Fixture Maintenance, press ENTER button to confirm, use UP and DOWN button to select Interval or Remain Time. ...
-
Page 21: Home Position Adjustment
5.2 Home Position Adjustment Press MENU button into menu mode, then press ENTER button for about 3 seconds into offset mode to adjust the home position. Select the function by ENTER button. Use UP and DOWN button to choose the submenu, press the ENTER button to store and automatically return to the last menu. Press MENU button to exit. PAN - pan home position adjustment Enter offset mode, Select PAN, press ENTER button to confirm, the present position will blink on the display, use UP and DOWN button to offset the value from ‐128 to 127, press ENTER button to store. Press MENU button to exit. ... - Page 22 COLOR - Color home position adjustment Enter offset mode, Select COLOR, press ENTER button to confirm, the present position will blink on the display, use UP and DOWN button to offset the value from ‐128 to 127, press ENTER button to store. Press MENU button to exit. GOBO - Gobo home position adjustment Enter offset mode, Select GOBO, press ENTER button to confirm, the present position will blink on the display, use UP and DOWN button to offset the value from ‐128 to 127, press ENTER button to store. Press MENU button to exit. PRISM 1 - Prism 1 rotation home position adjustment Enter offset mode, Select PRISM 1, press ENTER button to confirm, the present position will blink on the display, use UP and DOWN button to offset the value from ‐128 to 127, press ENTER button to store. Press MENU button to exit. PRISM 2 - Prism 2 home position adjustment Enter offset mode, Select PRISM 2, press ENTER button to confirm, the present position will blink on the display, use UP and DOWN button to offset the value from 0 to 255, press ENTER button to store. Press MENU button to exit. R‐PRISM - Prism1 rotation home position adjustment Enter offset mode, Select R‐PRISM, press ENTER button to confirm, the present position will blink on the display, use UP and DOWN button to offset the value from ‐128 to 127, press ENTER button to store. Press MENU button to exit. FOCUS - Focus home position adjustment Enter offset mode, Select FOCUS, press ENTER button to confirm, the present position will blink on the display, use UP and DOWN button to offset the value from 0 to 255, press ENTER button to store. Press MENU button to exit. ...
-
Page 23: Error Information
5.3 Error Information Lamp Startup Fail It appears when there is no lamp or some wires are damaged. Temperature Sense Error It appears when temperature check board is damaged. Lamp Too Hot Power Off It appears when temperature is detected higher than 110℃. Check if the unit is properly ventilated, or fans or temperature check board may is damaged. Lamp Too Hot Low Power It appears when temperature is detected higher than 105℃, the unit will run on a low power level. Maintenance Fixture It appears when the maintenance remaining time becomes 0S, please enter menu mode and reset the time. Lamp On Over 700 Hour It appears when the lamp has been on over 700 hours, please turn off the lamp. Memory Initial Fail It appears when the memory IC is damaged. CPU‐B Error, CPU‐C Error, CPU‐D Error They appear when board P.C or some wires are damaged. Pan Reset Error, Pan Encode Error, Tilt Reset Error, Tilt Encode Error, Shutter Reset Fail, Dimmer Reset Fail, Color Reset Fail, Gobo Reset Fail, Focus Reset fail. They may appear when turning on or resetting the unit, for some parts such as board P.C are damaged. Please contact the qualified maintenance. ... -
Page 24: Control By Universal Dmx Controller
6. Control By Universal DMX Controller 6.1 Connection 1. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120‐ohm 1/4W resistor between pin 2(DMX‐) and pin 3(DMX+) into a 3‐pin XLR‐plug and plug it in the DMX‐output of the last unit. 2. Connect the unit together in a “daisy chain” by XLR plug cable from the output of the unit to the input of the next unit. The cable cannot be branched or split to a “Y” cable. DMX 512 is a very high‐speed ... -
Page 25: Channel Mode Setting
6. 3 pin XLR connectors are more popular than 5 pins XLR. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (‐), Pin 3: Positive signal (+) 5 pin XLR: Pin 1: GND, Pin 2: Negative signal (‐), Pin 3: Positive signal (+), Pin4, Pin5 not used. 6.2 Channel Mode Setting Enter menu mode, select DMX Functions, press ENTER button to confirm, use UP and DOWN button to select DMX Channel Mode, press ENTER button to confirm, present channel mode will blink on the display, use UP and DOWN button to select Mode 1 (16) or Mode 2 (14) channel Mode, press ENTER button to store. Press MENU button back to the last menu or let the unit idle ... -
Page 26: Dmx 512 Configuration
6.4 DMX 512 Configuration 16 Channels Mode: ... - Page 28 14 Channels Mode: ...
-
Page 29: Troubleshooting
7. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The unit does not work, no light and the fan does not work 1. Check the connect power and main fuse. 2. Measure the mains voltage on the main connector. 3. Check the power on LED to see if it can be light up or not. B. Not responding to DMX controller 1. DMX LED should be on. If not, check DMX connectors, cables to see if they are linked properly. - Page 30 4. Try to use another DMX controller. 5. Check to see if the DMX cables run near or run alongside high voltage cables that may cause damage or interference to DMX interface circuit. C. One of the channels is not working well 1. The stepper motor might be damaged or the cable connected to the PCB is broken. 2. The motor’s drive IC on the PCB might be out of condition. D. The lamp is cutting out intermittently 1. The lamp is not working well. Check the mains voltage either too high or too low. 2. Internal temperature may be too high. Check if replacement of fan is needed on the head. E. If The pan belt is broken 1. Turn off the mains power. 2. Loosen the screws (A)，open the cover (B). 3. Loosen the screws (C). 4. Unplug all the connect wires over the belt. 5. Change a new belt (D), put the belt around the axis gear and motor gear. 6. Plug all the connect wires back upon the belt. 7. Tighten all the screws. F. If The tilt belt is broken 1. Turn off the mains power. 2. Loosen all the screws (A) and open the right arm cover (B).
-
Page 31: Maintenance And Cleaning
8. Maintenance and Cleaning Maintenance: Ballast A. As the pictures shown above, please replace the cable or cable joints immediately once they’ve turned yellow. B. Do maintain the fixtures every two months and make sure that all the screws and terminals have been locked firmly to make sure the normal performance of the fixtures. Negligence of maintenance would cause malfunction of the fixture. Cleaning: The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the ... - Page 32 MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany www.monacor.com 01.03.12.2015...
Need help?
Do you have a question about the BEAM-2R/PRO and is the answer not in the manual?
Questions and answers