Summary of Contents for Raycom RTB6211D
- Page 1 RTB6211D UHF FULL DUPLEX BASE STATION OPERATORS MANUAL (Preliminary)
-
Page 2: Table Of Contents
RTB6211D SYNTHESISED BASE STATION CONTENTS INTRODUCTION ..............................Front Panel ................................Rear Panel ................................Connector pinouts and switch information ......................AC Power inlet ................................12V DC INPUT ................................. Audio Inputs ................................Audio Outputs ................................Radio Control/Interface ............................. DIP Switches ................................Antenna Connections .............................. -
Page 3: Introduction
INTRODUCTION The Raycom RTB6211D is a synthesised Full Duplex NBFM/NXDN Digital Base Station designed for continuous operation. It is specifically designed to meet the requirements of both Studio and Outside Broadcast. The standard unit can be software configured for channels in the 440 - 470 MHz range. -
Page 4: Front Panel
18. R2 PEAK LED. When Radio 2 is in transmit active mode, LED illuminates to show transmitted audio is present. When Radio 2 is in receive mode, LED illuminates to show presence of received audio. 19. SUPPLY LED. When illuminated green, the base station has power (from either DC or AC inputs). RTB6211D Page ! 4... - Page 5 RTB6211D Page ! 5...
-
Page 6: Rear Panel
13. BNC 50 Ohm socket. Antenna connection for optional duplexer. 14. BNC 50 Ohm socket. High frequency input/output for optional duplexer. Normally connected to Radio 1 antenna connection with short U link cable. 15. BNC 50 Ohm socket. Radio 1 antenna connection. RTB6211D Page ! 6... -
Page 7: Connector Pinouts And Switch Information
AC Power inlet Fused IEC C14 inlet. Connect to an AC supply 90-264V, 47-63Hz. For other frequencies/voltages please consult Raycom. Fuse is 2A 20mm ceramic cartridge type. Tripping characteristic T (anti surge). A spare may be located in the fuse drawer. -
Page 8: Dip Switches
The optional duplexer module allows connection of the two radios to a single antenna system. When fitted, link the radio antenna ports to the adjacent duplexer port with the provided U link cables. The duplexer antenna port should be connected to the antenna system. RTB6211D Page ! 8... -
Page 9: Front Panel Usb Interface
Front panel USB Interface The RTB6211D has a pair of USB connectors on the front panel, adjacent to the display for each radio. Marked PROG, these connectors are used for programming each radio with the KPG-141D configuration software. All radio parameters, such as channel frequencies, spacing, power, modulation type etc are set with this software. -
Page 10: Operation
Operation RTB6211D Page ! 1 0... -
Page 11: Duplexer Module
Duplexer module RTB6211D Page ! 1 1... -
Page 12: General Performance/Specifications
± 5.0 kHz at 25 kHz ± 4.0 kHz at 20 kHz ± 2.5 kHz at 12.5 kHz Spurious Emission (EN) -36 dBm ≤ 1 GHz -30 dBm > 1 GHz Spurious Response (EIA) 80 dB RTB6211D Page ! 1 2... -
Page 13: Technical Description
Technical description RTB6211D Page ! 1 3... -
Page 14: Circuit Diagrams
Circuit Diagrams RTB6211D Page ! 1 4... -
Page 15: Warranty
Warranty RTB6211D Page ! 1 5... -
Page 16: Weee & Rohs Information
Raycom product - we can take-back waste equipment who's origin is a different producer. Products bought after that date are to be returned to their own producer or distributor. Raycom is not responsible for the cost of returning any equipment. -
Page 17: Declaration Of Conformity (Ce)
Declaration of Conformity (CE) RTB6211D Page ! 1 7... -
Page 18: About This Manual/Contacting Raycom
About this manual/Contacting Raycom RTB6211D Page ! 1 8...
Need help?
Do you have a question about the RTB6211D and is the answer not in the manual?
Questions and answers