Sailor H412 User & Installation Manual

Sailor H412 User & Installation Manual

Iridium ship security alert system

Advertisement

Quick Links

USER & INSTALLATION MANUAL
SAILOR H4122 Iridium Ship Security Alert System

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H412 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sailor H412

  • Page 1 USER & INSTALLATION MANUAL SAILOR H4122 Iridium Ship Security Alert System...
  • Page 2: About This Manual

    Disclaimer The SAILOR H4122 complies with these regulations and is approved Any responsibility or liability for loss or damage in connection with and certified by international classification services such as Det the use of this product and the accompanying documentation is Norske Veritas.
  • Page 3: Table Of Contents

    Contents Introduction ................ii About this Manual ............... ii Abbreviations ............... 1 System Overview ..............2 Operating - How to use the SSAS ........3 Normal mode ................3 Alert mode ..................3 Test mode ..................4 Iridium Tracking System ..............5 Connecting a PC ................
  • Page 4: System Overview

    System Overview Alert Iridium Satellite System Button Box Iridium SSAS Box E-mail, SMS Test Button Box Iridium System Iridium Gateway 39285 In case a ship is being attacked by pirates or terrorists the crew The system has full global radio coverage. Covers A1, A2, A3 and A4 needs a possibility to send a silent alert message to a predefined areas.
  • Page 5: Operating - How To Use The Ssas

    SIM card will be deleted in order to make room for receiving an alert Operating - reset SMS. How to use the SSAS Notice: It is possible to send alert messages and make a voice call at the same time but a data call will be interrupted when an alert is activated. Normal mode The contents of the message are shown in table 1.
  • Page 6: Test Mode

    Deactivating the alert Test mode The alert can be deactivated in two ways. The test mode is used to check that the system is working properly. Either by pressing the test button or by sending an SMS message to the system. The test message will contain the same information as the alert message (table 1).
  • Page 7: Iridium Tracking System

    Iridium Tracking System Connecting a PC With the Iridium Tracking System the SSAS control unit can send When the Iridium SSAS Box is in normal mode the data interface of information about the ships position. There are two ways to get the the Iridium transceiver can be used for various data applications, e.g.
  • Page 8: Installation

    Installation Technical Specification Input voltage: 10 – 32 VDC Current consumption: Max. 300 mA Operating temperature: -15 to +55 degree Celcius Interfaces: PC data port: RS232, 19200 baud Iridium data port: RS232 GPS input: NMEA 0183 version 2.20 and 2.30 Following NMEA messages are supported: GPRMC, GPGLL, GPVTG and GPZDA Check sum is recommended...
  • Page 9 Dimensions and drilling plan Mounting Iridium SSAS Box * 50 * 50 * Free space for mounting, ** Free space for cable entry. 258.5 39286 DRILLING PLAN Iridium SSAS Alert Button Box / SSAS Test Button Box 4 pcs. ø6 Cable entry DRILLING PLAN 3 pcs.
  • Page 10: System Block Diagram

    System Block Diagram Iridium Antenna Unit ABOVE DECK BELOW DECK Iridium Transceiver Unit Iridium Iridium Control SSAS Box Handset Option A Alert Button Box Alert Button Box GPS Input Max. cable loss 3dB Cable length max. 10m. Power supply Alert Button Box Alert Button Box 24V DC PC Interface...
  • Page 11: Interfaces

    Interfaces Iridium interface (data) GPS input Connector type: 9 pin Sub-D Male (Data Out) Connector type: 3 pole push connector Pin: Name: Function: Specification: Pin: Name: Function: RS422* galvanic isolated via Data Carrier Detect (in) NMEA+ GPS positive terminal optocoupler Receive Data (in) RS422* galvanic isolated via NMEA-...
  • Page 12: Cable Connection Diagram

    Cable Connection Diagram Fuse 1AF DC + DC − DC − NMEA + NMEA − Status Indicator Alert Button Box 1 Alert Button Box 2 Test Button Box 39288A 0435...
  • Page 13: Connection Scheme For Push Terminals

    The Iridium SSAS Box default IP parameters: Connection Scheme for push Terminals IP address: 192.168.2.40 Subnetmask: 255.255.255.0 Default gateway: 0.0.0.0 The IP address can be changed to fit any other local network. When 10 -32V DC DC + changing the IP address you must make sure to write down the new BAT + POWER DC -...
  • Page 14 there are several TCP/IP protocol installed. You can ignore the ones Now the Index page of the Iridium SSAS Box is shown. that have “Dial-Up” in the name associated with an internet service provider. In this example, the TCP/IP protocol associated with the If not then check the Internet settings and disable proxy server if this 3Com LAN network card has been selected.
  • Page 15: Configuration Parameters

    Configuration parameters Range Default value Description Parameter Message configuration Email address lenght: 25 chars Max limit for Email length can be set. Choosing 50 char will Max 25/50 chars automatically remove COG, SOG and "system" from the Ship's Name message. MMSI number When disabling one or more fields the additional text field will be Course Over Ground...
  • Page 16: Status And Message Log

    Step 1 Status and Message Log Connect the Ethernet LAN cable to the RJ45 connector on the Iridium SSAS Box. Status log A status log is maintained in the Iridium SSAS Box to provide Step 2 information to the user about failed connections to the GPS and the Set up the configuration table in the Iridium SSAS Box to have only Iridium Transceiver.
  • Page 17: Trouble Shooting

    Trouble shooting The status LED on the Iridium SSAS Box will flash in case the communication with the GPS or the Iridium Transceiver fails. (Refer cable connection) Slow flashing: No contact with Iridium transceiver unit Fast flashing: GPS signal is missing or the check sum is wrong Factory reset The SSAS control box can be reset by removing power from the Unit.
  • Page 19: Parts List

    Optional H4125 Iridium SSAS Alert Button Box 8041250206 H4126 Iridium SSAS Test Button Box 8041260206 SAILOR N163S AC/DC Power Supply, Blackgrey 80119410 Acessories ATO Blade Fuse 1AF 45.657 Cable for buttons 2 x 2 x 0.5mm2 – twisted pair with shield (specify length when ordering) 77.176...
  • Page 20 B4122GB0 Issue: G/0625 Thrane & Thrane A/S info@thrane.com www.thrane.com • •...

Table of Contents