Related Manuals for Target LaserTrack LT400
Summary of Contents for Target LaserTrack LT400
-
Page 1: Table Of Contents
ENGLISH TABLE OF CONTENTS PREFACE FAQ ABOUT TARGET LASERTRACK AREA OF APPLICATION OF INSTALLATION OF THE LT425 THE TARGET LASERTRACK CONTROL CIRCUIT BOARD AND THE LT420 BASIC TRANSPONDER CONTENTS OF THE PACKAGE AND OPTIONAL ACCESSORIES TECHNICAL SPECIFICATIONS IMPORTANT INFORMATION CONDITIONS OF GUARANTEE... -
Page 2: Preface
ENGLISH PREFACE You have just purchased a TARGET LaserTrack and are now the owner of a very advanced Class 1 laser remote control We believe our system can increase the comfort of system which can be used for various actions. The system... -
Page 3: Area Of Application Of
ENGLISH AREA OF APPLICATION OF THE TARGET LASERTRACK IS THE TARGET LASERTRACK DELIVERED IN 3 PACKAGES: LT 400 Vehicle System • 1 LT 400 car transponder (refer also to the accessories) • 1 LED • 1 Piezo signal device 1. Exterior lighting •... -
Page 4: Mounting And Connecting The Lt400 Car Transponder
INSTALLATION A special transponder for motorcycles is available. Follow the instructions below to the letter to ensure For motorcycles order the TARGET LT400-M. The control that the system performs optimally. elements of this set are completely waterproof and weatherproof. This system also has a special optical sig- MOUNTING AND CONNECTING nalling system that is always visible to the motorcyclist. -
Page 5: Transponder Alignment
ENGLISH CABLE CONNECTION: TRANSPONDER ALIGNMENT LT400 Connect to: The correct alignment of the transponder is very important. 1. Red Switched 12 V from the vehicle (+15). It should be aligned correctly vertically and horizontally. This is the cable with 12 V as soon as the vehicle is started. -
Page 6: Calculation Table For The
D. Use the table below when mounting the transponder in the grill or behind a vent hole of the vehicle. Mounting the TARGET LaserTrack using the parameters below guar- antees maximum performance. Grill/vent opening Measurements are in millimetres... -
Page 7: Testing The Operation
10 seconds. After the 10 seconds have The correct operation of the system can be tested after elapsed the system will emit two short audio signals. the TARGET LT400 has been installed according to the The LT400 is now in the stand-by mode. instructions. -
Page 8: Faq About Target Lasertrack
The system may not be used for other purposes than No, the Target LaserTrack is a Class 1 laser and is, that for which it was developed by the manufacturer. therefore, completely safe. -
Page 9: Installation Of The Lt425
ENGLISH INSTALLATION OF THE LT425 CONTROL CONNECTING THE LT 425 CONTROL CIRCUIT BOARD AND THE LT420 BASIC CIRCUIT BOARD TO THE GATE OR TRANSPONDER GARAGE DOOR MOUNTING THE LT420 BASIC TRANSPONDER The control circuit board is connected to the garage door 1. - Page 10 ENGLISH PROGRAMMING THE Program the second transponder in manner described TARGET LASERTRACK above if you have connected two LT420 transponders to a single control circuit board. 1. Park your vehicle at a few meters distance and in Important: The car transponder concerned has to be line with the basic transponder.
-
Page 11: Technical Specifications
ENGLISH TECHNICAL SPECIFICATIONS LT400 Type of emitter : Indium Gallium Arsenide laser diode, Class 1 Type of receiver : Infrared photodiode with optical and electronic amplifier Wave length : 904 nanometre Unique codes : > 4.500.000.000 Measurements in millimetres : Transponder 75 x 39 x 22 (l x w x h) Transponder housing : Aluminium, waterproof Supply voltage... -
Page 12: Conditions Of Guarantee
ENGLISH Conditions of Guarantee shown to the dealer. The buyer should also provide the warranty registration form with the stamp of the 1. The manufacturer guarantees the reliability of the dealer and the serial number of the system as well as system. - Page 13 ENGLISH...
- Page 14 ENGLISH...
Need help?
Do you have a question about the LaserTrack LT400 and is the answer not in the manual?
Questions and answers