Table of Contents
Advertisement
Quick Links
Instruction Manual
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL, TO UNDERSTAND
AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. IF YOU HAVE ANY QUESTIONS,
CONTACT WITH OUR REPRESENTATIVES OR DISTRIBUTOR.
34° Metal Connector
WARNING
BN3464JH No.01530000290
BN3438JH No.01630000290
BN3460JH No.02810000290
Advertisement
Table of Contents
Related Manuals for TESTO BN3464JH
Summary of Contents for TESTO BN3464JH
-
Page 1: Instruction Manual
34° Metal Connector WARNING BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL, TO UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. IF YOU HAVE ANY QUESTIONS, CONTACT WITH OUR REPRESENTATIVES OR DISTRIBUTOR. BN3464JH No.01530000290 BN3438JH No.01630000290 BN3460JH No.02810000290... -
Page 2: Table Of Contents
CONTENTS PAGE TOOL SPECIFICATIONS NAIL SPECIFICATIONS EXTERNAL TOOL PARTS SAFETY INSTRUCTIONS LUBRICATION AND MAINTENANCE ACTUATING TOOL OPERATING THE TOOL 9-10 TROUBLESHOOTING GUIDE... -
Page 3: Tool Specifications
TOOL SPECIFICATIONS Height ..................... : 11.4" (290mm) Width ....................: 3.5" (89mm) Length .................... : 11.8" (299mm) Weight .................... : 4.6 lbs. (2.1 kgs) Recommended Operating Pressure ..........: 70-120 psi (4.9-8.3 bar) Air Consumption ................: Loading Capacity ................: up to 32 nails NOISE CHARACTERISTIC VALUES IN ACCORDANCE WITH ISO 3774, ISO 11201: A-weighted single-event sound pressure level at operator's position .. - Page 4 TOOL SPECIFICATIONS Length ” 1 ” 1 Width ” 3 ” 3 Height ” 1 ” 1 Weight 70 ~ 120 psi 70 ~ 120 psi Operating Pressure (4.9 ~ 8.3 bar) (4.9 ~ 8.3 bar) Loading Capacity s l i s l i Accessories A-weighted single-event...
-
Page 5: Safety Instructions
SAFETY INSTRUCTIONS WARNING: Read this manual and understand all instructions before operating the tool. If you have any questions, please contact with our authorized representatives. The operator and all persons in the general area should wear safety glasses to guard against flying fasteners and debris, which could cause severe eye injury. - Page 6 Coupling must be used which removed all pressure from the tool when the coupling joint is disconnected. Never use tool that is leaking air, has damaged or missing parts. Never point the tools at co-workers or yourself at any time . Never carry the tool from place to place holding the trigger.
- Page 7 Never use the body of the tool or top cap as a hammer, always use the tool for its intended use. Do not discharge fasteners into concrete, stone, or any material too hard for the fastener to penetrate. Do not drive fasteners close to the edge of the work surface. The workpiece may split causing the fastener to ricochet, fly free or hit someone.
-
Page 8: Lubrication And Maintenance
LUBRICATION AND MAINTENANCE Use Pneumatic tool oil or a non-detergent oil. Do not use detergent oil or additives as they will damage o-rings and rubber parts. Use a filter and regulator when possible Add pneumatic oil into the air inlet twice daily. (Depending on frequency of tool use) Wipe tool clean daily and inspect for wear. -
Page 9: Operating The Tool
" Do not use on scaffoldings, ladders" , and shall not be used for specific application: when changing one driving location to another involves the use of scaffoldings, stairs, ladders, or ladder alike constructions, e.g. roof laths. closing boxes or crates. fitting transportation safety systems e.g. - Page 10 PLACEMENT OF NAIL: Metal connector nails are not designed to penetrate metal. When installing metal connectors, always place the exposed point of the metal connector nail into the metal connector’s pre-formed hole, and orient so the nail is perpendicular to the hole before attempting to drive a fastener.
-
Page 11: Troubleshooting Guide
TROUBLESHOOTING GUIDE WARNING: Disconnect air from tool before all repairs! Stop using the tool immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a qualified person or an authorized service center only.
Need help?
Do you have a question about the BN3464JH and is the answer not in the manual?
Questions and answers