Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Posch rz-600
-
Page 1: Operating Instructions
OPERATING INSTRUCTIONS Circular Saw with Roller Table RZ - 600 D100 0177 - Issue 9739 hese © Copyright by Posch Gesellschaft m.b.H., Made in Austria g the ® LEIBNITZ Internet: http://www.posch.com Dieses Dokument wurde erstellt mit FrameMaker 4.0.2. - Page 2 Operating Instructions and applicable safety and accident prevention regulations! Germany Austria OSCH OSCH Gesellschaft m.b.H. Gesellschaft m.b.H. Preysingallee 19 Paul-Anton-Kellerstraße 40 A-8430 Leibnitz/Kaindorf D-84149 Velden/Vils Phone (+43) 3452/82954 Phone (+49) 8742/2081 Fax (+43) 3452/82954-52 Fax (+49) 8742/2083 e-mail: export@posch.com e-mail: velden@posch.com...
-
Page 3: Table Of Contents
Contents General ..................2 Manufacturer ........................ 2 Application ........................2 Correct Application ...................... 2 Main Machine Parts ...................... 3 Description of Labels ....................4 Operating the Circular Saw ............5 General Safety Regulations .................... 5 Start-up ......................... 5 Longitudinal cutting ..................... 7 Saw Blade Change ...................... -
Page 4: General
General General Manufacturer Minimum cutting length: 10 cm Maximum wood length: 2 m Posch Gesellschaft m. b. H. Paul-Anton-Kellerstraße 40 Longitudinal cutting equipment A-8430 Leibnitz • Order no. F000 1417 Phone: (+43) 3452/82954 The longitudinal cutting equipment is Fax: (+43) 3452/82954-52... -
Page 5: Main Machine Parts
General Main Machine Parts Log gripper Interlock Shavings box Saw blade guard Table Stop pin Saw blade spanner (Pushing stick) Emergency stop pedal Universal shaft suspension Machine type sign Three point Fig. 1 - Circular saw with roller table Page 3... -
Page 6: Description Of Labels
General Description of Labels Before setting the machine into operation please Brennholzschneiden Nur mit allen read the operating instructions carefully! Gehörschutz tragen ohne Schutzvorrichtungen Schiebestock benutzen Zuführeinrichtung in Betrieb nehmen verboten use ear defenders use the log gripper use only with use the pushstick provided guards fitted... -
Page 7: Operating The Circular Saw
Table 2: Approved saw blade sizes Wear ear protection and goggles. Transport saw only with fixed table. Do not wear loose clothing. Only use original POSCH spare Never use faulty mains leads. parts. Ensure that working place is suffi- Never run machine unattended. - Page 8 Operating the Circular Saw Cutting Mount universal shaft and attach safety chain. Log gripper Check all bolts on guards and tighten if necessary. Check secure seat of circular saw blade and tighten hexagonal nut if nec- essary (see Fig. 9 - Saw blade change). The saw blade must turn without mak- ing contact.
-
Page 9: Longitudinal Cutting
Operating the Circular Saw C a u tion ! Don´t use the emergency stop Fold the table forward support continuous to switch off the machine. 2. After using the emergency stop you Saw blade guard must switch off the pto. Then retract the Log gripper emergency stop pedal in the starting position. - Page 10 Operating the Circular Saw Attach riving knife! Fold table back into base position and push back until it latches into posi- tion. Check correct setting of riving knife by setting machine to table position. Fig. 6 - Riving knife assembly Fig.
-
Page 11: Saw Blade Change
Operating the Circular Saw Saw Blade Change Attach longitudinal guard on frame. Longitudinal cutting guard (see Fig. 9 - Saw blade change) Ca ut io n! Disconnect circular saw from Longitudinal stop Clamping piece mains before saw blade change! Hexagonal nut Open-end spanner Stop pin Receiving plate... -
Page 12: Transportation
Operating the Circular Saw • Hold down the tensioning flange An appliance light must be attached with the open-end spanner supplied. to the rear of the machine. 3. Remove tensioning flange. • Order no. F000 1418 4. Change saw blade. We recommend The maximum transportation speed is 15 mph! the use of the following saw blades:... -
Page 13: Servicing
Never operate without guards. Attach all guards after servicing. Fig. 11 - Sharpening of saw blade Only use original POSCH spare parts. Setting of Saw Blade Never run machine unattended. (see Fig. 12 - Setting) -
Page 14: Additional Maintenance Information
Servicing Additional maintenance Lubrication of Right-angle Drive information Use EP oils with SAE 90 viscosity. In case of excessive wear, the wooden Type Type strips of the saw blade guide should be MP 85-W90 TransGearX-18 replaced. Table 5: Suitable hydraulic oils Dismantle the saw blade guard peri- odically and remove any residues. - Page 15 Servicing • Undo the tensioning and fixing screws of the gears. 3. Undo the hexagonal nuts of the metal flange bearings and lift the complete cir- cular saw shaft unit out of its frame. C aution ! Before lifting out the unit, mark up the position of the metal flange bearings.
-
Page 16: Fault Remedy
Fault Remedy Fault Remedy Fault Cause Removal Wrong rotation direction of saw See page 6 blade Blunt saw blade See page 11 Saw blade insufficiently set See page 11 Unsatisfactory cutting Tighten hexagonal nut performance Loose saw blade on drive shaft Worn V-belts See page 12 Circular saw blade covered... -
Page 17: Specification
Specification Specification RZ-600 Drive Saw blade rotation 1400 - 1600 Pto rotation Rotation Saw blade Diameter Log dimensions Maximum wood diameter Maximum wood length Minimum cutting length Dimensions Length Width Height Weight approx. Table 8: Specification Page 15... -
Page 18: Conformity Declaration
Conformity Declaration Roller table circular saw RZ-600 This product is subject to the EC design test stipulated by EC directive 89/392/EC. The following registered office Deutsche Prüfstelle für Land- und Forsttechnik Weissensteinstraße 70/72 D-34114 Kassel, Germany registered under no. 0363 a) holds the documentation according to appendix VI b) certifies that the documents according to appendix VI correspond to the regulations... - Page 19 ® Ihre Maschine LEIBNITZ Maschinentype Machine model/ Modèle de machine/ Machinetype/ Modelli macchine/ Maskintyp Artikelnummer Item no./ Référence/ Numero articolo/ Varenummer Seriennummer Serial number/ N˚ de série/ Numero di série/ Tillverkningsnummer Kaufdatum Date of purchase/ Date d'achat/ Datum van aankoop/ Data d'acquisto Österreich Deutschland OSCH...
- Page 20 Your Posch-Dealer: ® LEIBNITZ...
Need help?
Do you have a question about the rz-600 and is the answer not in the manual?
Questions and answers