1. Manuals
  2. Brands
  3. K-EIKO Manuals
  4. Rotary Hammer
  5. EDH620VRES
  6. Operator's manual

K-EIKO EDH620VRES Operator's Manual

Sds
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INDUSTRIAL POWER TOOLS
22mm
SDS ROTARY HAMMER
MODEL EDH620VRES
• 620W motor
• Impact energy of 2.2 Joules
• Push lock bit receptor for fast bit installation
• Variable speed and reverse
• Two mode action - rotary and hammer drilling
• Safety clutch
• Efficient dust and grease seal design
• Carrying case with bit storage compartment
WARNING: THE SAFETY INFORMATION
GIVEN INSIDE MUST BE READ AND
UNDERSTOOD BY ANY PERSON
USING, INSTALLING, REPAIRING
OR MAINTAINING THESE
TOOLS.
OPERATOR'S MANUAL
Please retain this information for future reference

Advertisement

Table of Contents
loading

Summary of Contents for K-EIKO EDH620VRES

  • Page 1 INDUSTRIAL POWER TOOLS 22mm SDS ROTARY HAMMER MODEL EDH620VRES • 620W motor • Impact energy of 2.2 Joules • Push lock bit receptor for fast bit installation • Variable speed and reverse • Two mode action - rotary and hammer drilling •...

  • Page 2: General Safety Rules

    d) Remove any adjusting key or wrench before turning GENERAL SAFETY RULES the power tool on. A wrench or a key left attached to a rotating part WARNING! of the power tool may result in personal injury. Read all instructions e) Do not overreach.

  • Page 3: Specifications

    Before starting to break, chip or drill into a wall, PRECAUTIONS ON USING ROTARY HAMMER floor or ceiling, thoroughly confirm that such items as electric cables or conduits are not buried inside. Wear earplugs to protect your ears during operation. Always hold the body handle and side handle of Do not touch the bit during or immediately after the power tool firmly.
  • Page 4 13 mm rotary hammer chuck For drilling operations when using a straight shank bit for impact drilling with a rotary hammer. Straight shank bit 13 mm Rotary hammer chuck for impact drill (SDS-plus shank) Chuck wrench 2. Anchor setting (rotation + hammering) Anchor setting adapter (for rotary hammer) Anchor setting adapter (SDS-plus shank) (for rotary hammer)
  • Page 5 4. Crushing operation (rotation + hammering) Bull point (Round type only) (SDS-plus shank) 5. Bolt placing operation with Chemical Anchor. (rotation + hammering) (SDS-plus shank) Standard socket on the market 12.7 mm Chemical Anchor Adapter 19 mm Chemical Anchor Adapter 6.
  • Page 6 7. Drilling holes (rotation only) Drill chuck (13 VLD-D) Chuck adapter (D) (SDS-plus shank) Chuck wrench 13 mm drill chuck ass’y (includes chuck wrench) and chuck (for drilling in steel or wood). 8. Driving Screws (rotation only) Chuck adapter (D) Bit No.

  • Page 7: Prior To Operation

    (4) To remove the drill bit, fully pull the grip in the APPLICATIONS direction of the arrow and pull out the drill bit (Fig. 2). Rotation and hammering function Drilling anchor holes Drilling holes in concrete Drilling holes in tile Rotation only function Drilling in steel or wood (with optional accessories)

  • Page 8: How To Use

    CAUTION 2. Rotation + hammering The dust cup and dust collector (B) are for exclusive This rotary hammer can be set to rotation and use of concrete drilling work. Do not use them for hammering mode by pressing the push button and wood or metal drilling work.
  • Page 9 Do not attempt to use the rotary hammer in the To drill wood or metal material using the drill chuck rotation and striking function with the chuck adapter and chuck adapter (optional accessories), proceed as follows. and bit attached. Installing drill chuck and chuck adapter: (Fig. 9) 5.
  • Page 10 (3) Turn the switch ON, and drill a hole in prescribed (3) Insert the center pin into the guide plate until it stops. (4) Engage the guide plate with the core bit, and turn the depth. (4) To remove the drill bit (taper shank), insert the cotter guide plate to the left or the right so that it does not into the slot of the taper shank adapter and strike the fall even if it faces downward (Fig.

  • Page 11: Maintenance And Inspection

    LUBRICATION IMPORTANT: Correct connection of the plug Low viscosity grease is applied to this rotary hammer so The wires of the mains lead are coloured in accordance that it can be used for a long period without replacing with the following code: the grease.
  • Page 13 HEX. HD. TAPPING SCREW D4 × 50 TAPPING SCREW (W/FLANGE) D5 × 35 STATOR GEAR COVER BALL BEARING 608VVC2PS2L HITACHI LABEL (A) HOUSING PUSHING BUTTON PUSHING SPRING K-EIKO LABEL NAME PLATE CHANGE LEVER PUSHING BUTTON O-RING (S-18) CARBON BRUSH OIL SEAL SPRING SLEEVE TAPPING SCREW D3 ×...
  • Page 16 EC DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with standards or standardized documents EN60745, EN55014 and EN61000-3 in accordance with Council Directives 73/23/EEC, 89/336/EEC and 98/37/EC. Manufactured for KENNEDY TOOLS Wigston Works, Leicester, England. ISO 9002 REGISTERED COMPANY Signed: Date: 31 July 2006...

Table of Contents