Summary of Contents for Superior Listening systems CM208W
- Page 1 CM208W Series Subwoofers User/Installer Manual CM208W CM208W-TB CM208W-SR Rev: 707 1650 W. Jackson Ozark, MO 65721 (417) 883-4549...
- Page 2 Page 2 of 11 Introduction Congratulations on your purchase of the CM208W series subwoofers. These subwoofers feature (2) long- throw 8” drivers capable of response down to 35Hz with a peak SPL capability of 112dB per cabinet. These subwoofers also feature a flexible input and output feature set that allows use with all of our wall and ceiling mount full range speakers.
- Page 3 8 ohm speaker model can be used with the subwoofer. Best results will be obtained by using SLS satellites however as the internal crossover in the CM208W series subwoofers are optimized for SLS wall and ceiling speakers.
- Page 4 Page 4 of 11 CM208W Series 70V Wiring Schemes 70V Configuration with Subwoofer & 4 Satellites (with optional internal 70V transformer) Stand Alone Subwoofer w/rigging points and optional transformer 70V Output (60W Loading) Tile Bridge Subwoofer with optional transformer Sheetrock Subwoofer with optional transformer (4) 8 ohm Satellites 70V Configuration with Subwoofer &...
- Page 5 Page 5 of 11 CM208W Series Bi-amp Wiring Schemes Bi-Amp Configuration with Subwoofer & 2 Satellites Stand Alone Subwoofer w/rigging points (CM208W shown) Speaker Level LF (8 ohm load) Tile Bridge Subwoofer (CM208W-TB) Sheetrock Subwoofer (CM208W-SR) Speaker Level HF (4 ohm load)
- Page 6 Page 6 of 11 CM208W Series Bi-amp Wiring Schemes Bi-Amp Configuration with Subwoofer & 4 Satellites Stand Alone Subwoofer w/rigging points (CM208W shown) Speaker Level HF (8 ohm load) Tile Bridge Subwoofer (CM208W-TB) Speaker Level LF (8 ohm load) Remove lnput Jumpers...
- Page 7 1/8” wire rope is the minimum recommended sizing for the rigging materials. The CM208W can be flown either from the top as shown or from the back so that the woofers are facing downwards. The performance differences will be small between the two options so the venue requirements...
- Page 8 Page 8 of 11 CM208W-TB Installation Guide The CM208W-TB variant is designed to be installed in 2’ x 2‘ tile bridge ceilings. You will need 18.5” (47cm) of clearance above the tile grid for installation. - The (4) eyebolts are included in the installation ring’s box. These should be installed first.
- Page 9 Page 9 of 11 CM208W-SR Installation Guide The CM208W-SR variant is designed to be installed in sheetrock ceilings. It ships with a pre-installation ring and an external white grill. You will need 16” (40.6cm) of clearance above the bottom of the ceiling joist for installation.
- Page 10 Page 10 of 11 CM208W-SR Installation Guide (cont.) - Once the sheetrock is finished, use a spiral saw (with a bit that contains a guide) to cut away the sheetrock from the main center hole. After this, reset the bit and route out the sheetrock from the recess for attaching the subwoofer.
-
Page 11: Specifications
Page 11 of 11 Specifications CM208W-TB / CM208W-SR Product Specifications Operating Range 35 - 200Hz Sensitivity (1W/1M - 1/2 Space) 89dB Horizontal Coverage Angle -6dB Omni Vertical Coverage Angle -6dB Omni Power Handling 200W RMS Max SPL (calculated) 1 Meter...
Need help?
Do you have a question about the CM208W and is the answer not in the manual?
Questions and answers