Subscribe to Our Youtube Channel
Summary of Contents for XK DHC-2 A600
- Page 1 DHC-2 A600 5CH BRUSHLESS MOTOR 3D6G SYSTEM AIRPLANE Quick Start Guide www.xk-innovations.com...
-
Page 2: Table Of Contents
Introduction Thank you for purchasing Our XK A600 DHC-2 beaver simulation plane, the plane used 6 axis gyroscope (compatible with the 3D/6G 3 axis gyroscope)With the function of 3D transfer to 6G, 4-CH Single wing layout is very suitable for you to do sports and leisure flying, even if you are a beginner, in 6G mode also can be easy to flight. -
Page 3: Safety Precautions
Safety precautions The hobby belong to the dangerous goods, flying must be away from people. If Install not well or spare parts broken, Tranmitter control broken, and not have experience of handing, It all may causing flight out of control and broken. Pls be carefully for flying. And you must to know that the duty of wrong handing is in charge of yourself. -
Page 4: Packing List
Remote control like the real machine is mostly EPS foam, electronic products as the main material, so try to keep away from heat, sunlight, to avoid distortion caused by high temperature and melt the possibility of damage. This product is suitable for more than 14 years of age, flight the real machine would be a little difficult to learn . -
Page 5: Controller Diagram
Controller diagram MODE 1(the asia version） antenna power indicator light throttle trim throttle/direction joystick （press the rudder key to change） elevator /joystick （press down 6G/3D Switch） elevator trim Aileron trim direction trim power switch LED display MODE 2(European Version） antenna power indicator light elevator trim throttle/direction joystick... -
Page 6: Battery Charging
Battery charging 1. The power adapter connected with lipo charger. 2. And then put the charger into AC socket,at the same time the indicator lamp of lipo charger (green light) lights. 3. Put battery plug into charger,the indicator lamp (red light) lights, The The battery is saturated after lights out. -
Page 7: Landing Gear Installation
Landing gear installation Front Landing gear put into head at the bottom of the interface as shown A.And then back landing gear Installed in the tail bottom interface as shown. B.At last Install the front landing of Two pieces of component into Front landing gear Support bar. -
Page 8: Receiver Plugs Introduction
Receiver plugs introduction code key ESC socket Aileron socket battery Socket deirection socket lifting socket Rudder adjustment of plane 1. Put into battery for the plane, Aileron/lift Rudder Vertical rudder Should back to middle. If the rudder is not in the middle position, By hand rotation of the adjustment will be adjusted to the middle position of the rudder. -
Page 9: Take Off On The Ground
MODE ICON MODE ICON 上升 go down rudder rudder face up down rolling rolling left right down down Rudder left Rudder righti turn turn left right Take off on the ground 1.The plane facing the windward on the Ground, Confirm each Rudder back to middle again,The rudder direction is correct or not. -
Page 10: Landing
Landing Pls land immediately when the you feel the plane lack of power. First of all, the plane flew to windward area adjust the head and upwind landing. Pull down throttle and reduce the flight speed. The plane will slowly slider down. Until the plane touches the grounp. -
Page 11: Flight Finish
Flight finish End of flight,pls bring down the batteries. warn: If the battery not removed will be cause Excessive battery discharge and damage, Even cause fire. Turn off the power of Transmitter When you turn off the power of Transmitter, and long time not play it, pls bring down the battery and keep it. -
Page 12: Motor Replacement
Motor replacement 1. Remove 2 pcs screw from firewall by twisting. 2. The motor one the firewall tried to pull out. 3. Remove the screw which one on motor by twisting. 4.Separate motor with fixed plate, re-placement the new motor. Note: The plane after using. - Page 13 reason countermeasure The status Push the motor but Motor and ESC bad contact Motor socket connecting motor did not start or motor break down. or change motor. properly, motor in turn. The motor socket connection Motor gear appear less teeth. Replace the motor with problem.
- Page 14 Shenzhen XK Innovations Technology Co., Ltd. Email:sales@xk-innovations.com...
Need help?
Do you have a question about the DHC-2 A600 and is the answer not in the manual?
Questions and answers