3. Safety Instructions and Precautions 4. Setup and User Instructions 5. Replacement Parts 6. Technical Specifications 7. Conformity RadioLink Television Radio System – Universal Radio Transmitter & Receiver Please read and follow the safety instructions before using the product...
Accessories Picture: ① ② ③ ④ Receiver Charger Transmitter SCART\ Adapter ⑤ ⑥ ⑦ ⑧ Power adapter Power adapter Headset Phono plugs ⑨ Neckloop ① ③ ② ⑤ ④ ⑥ ⑦ ⑨ ⑧...
FEATURES: 1. Active noise reduction system for crystal clear sound 2. Operation distance up to 50 meters open air 3. Transmits through walls at home 4. Tone Control (Low/Mid/High) can be set independently. Receiver has auto channel search tuning 6. Li-ion battery technology ensures a long operating time...
Using this product inappropriately could adversely affect your hearing. Please follow the step-by-step instructions carefully! Do not use in an environment that is damp, wet, very hot or very cold. To clean the RadioLink and its accessories, use only a soft cloth and an inorganic cleaner.
Setup and User Instructions: 1.Place the RadioLink transmitter near to the TV.(see Fig 1) ① 2.Plug the 12V DC Power Adapter into a standard electrical wall socket, then connect the end of output lead into the transmitter DC12V socket. (see Fig 2) ②...
Page 7
5.If your TV has phono audio output sockets connect the 2 x phono plugs of the phono to 3.5mm lead to these sockets and plug the 3.5mm jack plug end of the lead into the RadioLink Transmitter Audio input socket (see Fig 3).
Page 8
7.If the SCART connection is not successful, Fig 5 connect the microphone. Simply plug the 3.5mm plug of the microphone cable into the Mic socket on the transmitter (see Fig 5) and then the microphone onto the TV speaker, using the Velcro. 8.Remove the receiver from the base (or from the Y patch lead) and fully insert the Headset or Neckloop plug into the phone...
Page 9
14.The red charge LED on the receiver will light up red and when the batteries are fully charged again it will turn green. Note: The red LED on the charging base will always be red when connected to the mains.
Page 10
Help and advice for connecting to TV with analogue audio output. When connecting a MegaLoop , EchoLink or RadioLink to a TV. It is usually best not to use the SCART sockets as this can result in picking up the wrong sound or sound that is out of sync with the picture.
Page 11
Help and advice for connecting to a TV. that has Digital Optical Audio Output Many of the newer TV. models no longer have analogue audio output, they have Digital Optical Audio Out or Digital Coaxial Audio Out. The picture below shows the type of socket to look for. To connect your equipment from this socket you will require an optional Digital to Analogue Converter available from Hearing Products International Ltd.
Replacement Parts Description 465TX RadioLink Transmitter (TX) 465RX RadioLink Receiver (RX) 465base Charger Base for RadioLink 570-1000-01 12V DC power supply positive centre 575-1000-01 UK Plug 490-1013-01 RadioLink Carton/Instructions 306/B phono phono combi lead 201/B Scart/phono plug 202/M Mic on lead (mono plug)
Page 13
1 System VHF/RF 2 Carrier frequency 174.0MHz; 174.5MHz; 175.0MHz 3 Modulation 4 Mode stereo 5 Transmit power 7dBm(maximum) 6 S/N ratio 65dB 7 Channel separation 50dB(minimum) Distortion 1.5% 9 Frequency response 30 - 20,000Hz 10 Power supply of transmitter DC 12V Positive Centre min 200mA TX can also be powered by 11 Optional 2 x AAA Alkaline batteries...