Summary of Contents for Brett-Guard 10A
- Page 1 ® OPERATORS MANUAL Original Style 10A, L, LB, LR, LRB Caution: Read all instructions carefully. SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. Date Purchased: Where Purchased: Address:...
-
Page 2: Table Of Contents
A Word About Your New Brett-Guard Table of Contents The Brett-Guard Table Saw Safety Tool is designed for the discriminating General Product Safety Warning....2 woodworker — The craftsman who wants quality, function, and performance without sacrificing safety and flexibility. Brett-Guard is designed to overcome Warnings .......... - Page 3 Drugs, alcohol, or medication. Stay alert. Watch what you are doing. Use common sense. Do not operate tool when you are tired, upset, ill, or while under the influence of drugs, alcohol, or medication. 8. First aid. Have at least one person with first aid training and first aid kits approved by American National Red Cross available at all times.
-
Page 4: Warnings
All Table Saws are inherently dangerous and should never be used by anyone who is not thoroughly trained and experienced. The Brett-Guard Table Saw Safety Tool, properly installed and used under proper supervision, can help to protect an operator against injury from many saw hazards such as coming in contact with the saw blade, kickbacks and flying splinters but NOTHING can protect an operator if proper operating procedures are not followed. -
Page 5: Operating Instructions
Operating Instructions The use of the BRETT-GUARD Table Saw Safety Tool (Guard) is basically quite simple. But, due to the serious nature of operating a table saw, there are many factors to be considered. The following pages show most of the important factors to consider for safe table saw operation. - Page 6 Warning: For the Anti-Kickback device to function and/or the Shield to serve as a hold-down device, it is imperative that the shield be adjusted so that the lower edge of the shield applies a light pressure to the top of the workpiece.
-
Page 7: Ripping Reminders
Ripping Reminders: Tenoning 1. Mount the Brett-Guard on the left side of the Table Saw. 2. Always have the splitter installed 3. Raise the shield enough to clear the blade. Position shield so the blade is about 1" inside the edge of the shield. -
Page 8: Assembly And Installation
2. Thread two (2) 5/16 - 18 x 1" Lock knobs into the Brett-Guard housing as shown on Page 4 - Component Description. 3. Insert the shield support rods into the housing slide and lock into position with the knobs installed in previous step. -
Page 9: Maintenance Instruction
4. Attach the rear mounting plate to the arms using (4) 5/16" - 18 x 1" bolts, flatwashers, lockwashers and hex nuts. Hand tighten only. 5. Lock the Brett-Guard onto the rear plate. Lower the shield until it is about 1/4" from the table top. Gently Figure 4 tap the plate until the shield is level with the table and tighten all fasteners. -
Page 10: Parts
Parts 37 - “L” 37 - “B” 37- “R” 37 - “S” 44, 45 Key Model No. Description Weight (UPS) 20030 Replacement ‘Plexiglas’ Shield for 10A Guards 20030P Replacement ‘Plexiglas’ Shield w/2" Dust Port... - Page 11 Parts Key Description Part# Qty. Key Description Part# Qty. Housing Assembly, ‘Original’ style 20500 30 Kickback Assembly Knob 20039 See Note #1 31 Kickback Actuator 20054 Housing Body 20001 32 Kickback Threaded Insert 20038 Crank Rod, threaded 20008 33 Kickback Plate 20040 Crank Rod, Bushing, upper 20011...
-
Page 12: Warranty
LIMITED LIFETIME WARRANTY Products manufactured by HTC Products are guaranteed to be free from defects in material and workmanship under normal use and service. HTC’s obligation under this warranty shall be limited to repairing or replacing for the original owner, at our option, any part of said equipment which HTC’s examination shall disclose to its satisfaction to be thus defective.
Need help?
Do you have a question about the 10A and is the answer not in the manual?
Questions and answers