Summary of Contents for RIKA PELLET CONTROL
- Page 1 PELLET PELLET PELLET PELLET CONTROL L L L CONTRO CONTRO CONTRO Operating instruction Page 1 of 24...
- Page 2 Page 2 of 24...
-
Page 3: Table Of Contents
3.1. General information..............5 3.2. Wall mounting, cable routing ............5 3.3. Cable specification ..............5 4. Operation of the pellet control .............. 7 5. Pellet control functions ................. 7 5.1. Room set temperature..............7 5.2. Heating times ................8 5.3. -
Page 4: Pellet Control (External Control Unit)
Pellet control (external control unit) The pellet control unit controls the basic functions of the pellet stove and permits the desired room temperature to be programmed for heating and cooling operation and control of frost protection operation. A large graphics screen displays the operational and programming functions. -
Page 5: Assembly Of The Pellet Control
Then mount the housing on the wall using the rear panel. 3.3. Cable specification To connect the operating unit you will require a commercially available 4-pin sheave cable. The cable enables all data exchange between the main board and the pellet control and the electrical supply. Page 5 of 24... - Page 6 Connect the control cable in the correct wire sequence to the 4-pin plug supplied (as shown in figure 4). Plug the plug into the socket of the pellet control. Now snap the front section of the pellet control into the rear housing panel.
-
Page 7: Operation Of The Pellet Control
4. Operation of the pellet control Once installation is complete you can reconnect your device to the mains. When using the pellet control, the internal control unit = user board does not display any information. The pre-stored data of the internal control unit is automatically accessed by the pellet control. -
Page 8: Heating Times
Room temp. 0-220 ° F Display of the desired temperature for state ON Room temp. OFF, OFF indicates that the stove is turned off. 0-220 ° F Otherwise controls regulate to maintain programmed temperature Frost 0-220 ° F Frost protection will be activated, if stove is turned protection off in OFF and if room temperature fell below frost Min. -
Page 9: Room Set Temperature, Weekly Heating Schedule
5.3. Room set temperature, weekly heating schedule When you first plug-in your stove to the power outlet (with the pellet control installed), the following information appears on the pellet control display: This symbol indicates that the control is in the standby position and is ready for operation. - Page 10 The hour for OFF 1 is inverted and can be changed in steps 1234567 of one hour as desired by pressing "+" and "-". The required ON 1 06:15 OFF1 00:00 setting is confirmed and saved with "ENTER". The display ON 2 00:00 shows: OFF2 00:00...
- Page 11 1234567 „2“ (inverted) stands for Tuesday. ON 1 00:00 OFF1 00:00 ON 2 00:00 OFF2 00:00 Press „ENTER“ and the display appears: 1234567 The display shows the hour (inverted) for the first heating ON 1 00:00 time on Tuesday. OFF1 00:00 ON 2 00:00 OFF2 00:00 Now enter all the other heating time settings for Tuesday and for the remaining...
- Page 12 For a room set temperature of OFF the device is switched OFF and the frost protection mode is activated. The required setting is confirmed and saved with "ENTER". The display shows: “CLEAN” indicates the cleaning function. The number shows CLEAN MODE the length of the cleaning interval in minutes (e.g.
- Page 13 “VERS” stands for the actual stove control program version (indication only) With the “+” and “-“ keys the current time (highlighted) is set and quit using “ENTER” and the display shows: TIME Set the current minute (highlighted) using “+” and “-“ and quit 13:48 - 2 with “ENTER”...
- Page 14 The room set temperature can be changed from 0 to 220° F using “+” and “-“. The new value is used immediately for control. If the room temperature reaches the room set temperature, the indicator for the current room temperature extinguishes. Upon reaching the room temperature, the stove is switched off.
-
Page 15: Main Menu - Operating Modes
5.4. Main menu – operating modes According to your requirements you can choose between the following three operating types described below. Standby-mode: • This symbol indicates that the control is in standby mode. STANDBY Manual control (room temperature controlled): • “70°... - Page 16 The clock symbol (colored red) indicates the automatic mode. The symbol indicates that the clock is in standby. “OFF” indicates that the pellet stove is switched off and standing by for frost protection operation or the next programmed heating period. The individual operating modes can be changed by selecting “ENTER”.
- Page 17 Start automatic operation (TM mode) If automatic operation is selected on the display and the programmed heating time begins, the control starts the heating operation. The following alternating indication appears on the display: START 70°F TEMP. 69.5°F 21 MIN „START“ indicates start. The number below indicates the remaining time for the start procedure in minutes (here 21).
-
Page 18: Turning The Stove Off
5.5. Turning the stove off Switching over from manual operation (ON) • If the “ON/OFF” switch is pushed during operation or the room set temperature reached, then the shut-down program is activated. The display shows the following alternating indications: EXIT 1 70°F TEMP. -
Page 19: Switching Over From Automatic Operation (Tm)
The number below shows the remaining time until exit in seconds (here 300). On completion of EXIT 2 the display goes dark. Re-start commences only if the “ON/OFF key is pressed. Note: The full shut-down process lasts for about 8 minutes and cannot be interrupted by the user. -
Page 20: Switching To Standby Using "Operation Mode" (Sb)
Switching to standby using “operation mode“ (SB) • If you press the “ENTER” key to switch out of “manual operation” or from “automatic operation” to “standby mode” a starting procedure as described above will be carried out. On completion of the switching program the following appears on the display: STANDBY To restart operation a corresponding mode must be selected, or the device must be started using the optional Tele-Control (telephone start). -
Page 21: (From Stove Control Program Version V 1.22A)
Menu flow chart for programming the pellet control (from stove control program version V 1.22A) Menu level: 70° F 70° F Selection for operating mode Enter Enter TEMP. TEMP. 68.5°F STANDBY 68.5° F Enter Automatic mode MENU Programming for heating... - Page 22 Page 22 of 24...
- Page 23 Page 23 of 24...
- Page 24 Administration/Sales: RIKA Metallwarenges.m.b.H & Co KG Müllerviertel 20 A-4563 Micheldorf Tel: 0043(0)7582/686-41 Fax: 0043(0)7582/686-43 Email: verkauf@rika.at www.rika.at Production/Goods inwards and outwards store: A.G.Z. Adlwanger Gewerbe Zentrum Brandmühlestrasse 6 A-4541 Adlwang Page 24 of 24...
Need help?
Do you have a question about the PELLET CONTROL and is the answer not in the manual?
Questions and answers