Subscribe to Our Youtube Channel
Summary of Contents for Mustang Survival MD3090
- Page 1 Owner’s Manual MD3090 and MD3095 Compact Tactical Life Preserver *Shown with the MA3090 Chest Belt/Crotch Strap Assembly...
-
Page 2: Table Of Contents
CONTENTS Page 1 Description 2 Instructions for Use 2 Check Your MD3090 or MD3095 Before Using It 3 Sizing and Fit 4 Donning Instructions 4 Inflating Your MD3090 LP 5 Re-arming Your LP After Manual Inflation 6 Re-arming your MD3095... -
Page 3: Description
It is always recommended that users perform their own in-water test with full gear. The Mustang Survival MD3090 and MSD3095 can be attached to a body armor vest or worn as a stand-alone life preserver using the chest belt/ crotch strap assembly MA3090. -
Page 4: Check Your Md3090 Or Md3095 Before Using It
Beaded Handle Check Your MD3090 or MD3095 Before Using It After purchasing your MD3090, make sure it has an unused 33 gram CO 2 cylinder attached to the inflator mechanism (Fig. 1). Check the components and how to assemble the inflator by following these steps: 1) Undo the Velcro™... -
Page 5: Sizing And Fit
2) Unscrew and remove the CO 2 gas cylinder from the inflator and inspect its small end. If it is pierced, replace it (Fig. 4)! FIGURE 4 3) Make sure the manual lever is in the up-and-ready position and insert the green indicator pin if not already in place. Ensure the CO 2 cylinder is screwed hand tight into the inflator. -
Page 6: Donning Instructions
An incorrect fit or improper fastening of attachments could impede its effectiveness. 1) Belts and straps need to be adjusted for fit. When the MD3090 is integrated with MOLLE body armor vest, ensure the connections are securely fastened (P. 11). When the MD3090 is used with the MA3090 chest belt/crotch strap assembly, the waist belt should fit securely (P. - Page 7 3) Install an unused CO 2 cylinder by screwing it into the top of the inflator and hand-tighten. Do not over-tighten, as this can damage the internal gasket. 4) Refold the LP in accordance with the repacking instructions (P. 6). Your MD3090 is now ready for use. Piercing Green Indicator...
-
Page 8: Re-Arming Your Md3095
Re-arming Your MD3095 NOTE: A re-arm kit (MA7203) is required for this procedure. 1) Hold the cover in one hand, reach under the cover with the other hand and grasp the plastic housing of the inflator. Pull the inflator toward you, turning the bladder and cover inside out to fully expose the inflator for re-arming. -
Page 9: Repacking Your Md3090
1) Fold lapels (A) across the front along the dotted line shown in Fig. 2) Fold side (B) inward along dotted lines. Secure with Velcro™ (Fig.12). 3) Fold outer lapel (C) and secure Velcro™ (Fig. 13). Your MD3090 or MD3095 will look as illustrated in Fig. 14. -
Page 10: Usage In Freezing Conditions
Usage in Freezing Conditions When the temperature is below freezing, a fully discharged cylinder may not adequately inflate your MD3090 or MD3095 LP. Oral inflation may be required to fully inflate the LP in freezing conditions. WARNING: CO 2 inflation could over-pressurize and damage your LP if already fully orally inflated. -
Page 11: Care And Maintenance Instructions
4) Check the manual lever to ensure it is in the up and ready position, with the green indicator pin properly installed (MD3090 only). 5) To check the oral inflation valve, fully inflate the MD3090 or MD3095 and hold the valve under water. If bubbles appear, deflate and reinflate to test again. -
Page 12: Safety Accessories
Safety Accessories MA7170 33 gram CO 2 replacement cylinder and green indicator pin. MA7203 33 gram CO 2 replacement cylinder/bayonet assembly. MA3090 Chest Belt/Crotch Strap Assembly. Cleaning and Storing Your LP To clean your inflatable LP, remove the CO 2 gas cylinder. Hand wash or sponge down in warm, soapy water and rinse with clean water. -
Page 13: How Do You Test Your Lp Using The Oral Inflator
· Re-arming kit approved for your LP. 2) Put on the LP. 3) Actuate the inflation system by jerking firmly downward on the beaded handle. The LP should fully inflate within 5 seconds. 4) Get into shallow water, just deep enough that you can stand with your head above the surface. -
Page 14: Integration Instructions With Body Armor
1) Lay the body armor vest down on a clean flat surface with the back of the vest facing up. Lift up the emergency extraction strap on the back of the vest and loop the back attachment of the MD3090 Life Preserver around the extraction strap (Fig. 17). - Page 15 Back view after attachment (Fig. 19). FIGURE 19 3) Turn the vest, with the attached MD3090 Life Preserver over and lay with the front of the vest facing up. Position the two front lobes of the Life Preserver perpendicular to the webbing running across the vest (Fig.
- Page 16 5) Loop the male buckle back over the 4th row of webbing and fasten it to the female buckle. Cinch by pulling down on the loose end of the webbing (Fig. 22). Repeat for the other side. FIGURE 22 Row 3 Row 4 Additional Steps: a) Fasten the buckle that connects the left and right lobes in front of...
-
Page 17: Attachment Instructions For Ma3090 Chest Belt/Crotch Strap Assembly
D. T-tab junction with snap (Fig. 24). FIGURE 24 2) Insert the short side of the webbing attachment, on the back of the MD3090 life preserver, through Looploc (A) on back strap of the chest belt accessory (Fig. 25). Securely fasten the snap. FIGURE 25... - Page 18 3) Locate T-tab junction at the top of the crotch strap (D) and thread through the lower back chest belt loop. Secure the T-tab with the snap. Once the snap is securely fastened, turn the snapped portion so it is positioned inside the chest belt loop away from the body (Fig. 26).
- Page 19 5) Repeat step 4 with buckle attachments (B) for the other side (Fig. 28). FIGURE 28 6) Unfasten the crotch strap. Put the life preserver on as shown (Fig. 29). 7) Buckle chest buckle that connects the right and left lobes of the life preserver (Fig.
- Page 20 FIGURE 32 Compact Tactical Life Preserver Owner’s Manual...
- Page 21 Compact Tactical Life Preserver Owner’s Manual...
- Page 22 Bellingham, WA USA 98226 Mustang Survival and seahorse design is a registered trademark of Mustang Survival Corp. Our commitment to quality has earned our Richmond facilities ISO 9001 registration, the highest of all international standards. This is our guarantee you’re receiving the ultimate in design and manufacturing.
Need help?
Do you have a question about the MD3090 and is the answer not in the manual?
Questions and answers