GrandTec POE-5000 Quick Installation Manual

5-port gigabit poe+switch (30w)

Advertisement

Quick Links

Introduction ...........................................................
Unpacking and Installation ......... ..............................
System Requirement....... .......................................
Front Panel /LED.....................................................
Hardware Installation... ............. ...............................
Technical Speci cation..............................................
Troubleshooting .......................................................
FCC Warning:
This device has been tested and found to comply with the regulations for Class B digital equipment.
Pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with users guide, may cause harmful interference to radio communications. Operation of this device in
a residential area is likely to cause harmful interference, in which case the user will be required to
correct the interference at his/her own expense.
CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
UL Warning:
1> Elevated Operating Ambient Temperature- If installed in a closed or multi-unit rack assembly, the
operating ambient temperature of the rack environment may be greater then room ambient. Therefore,
Consideration should be given to installing the equipment in an environment compatible with
manufacturer's maximum rated ambient temperature
2> Reduced Air ow-installation of equipment in a rack should be such that the amount of air ow required
for safe operation of the equipment is not compromised.
3> Mechanical Loading- mounting of the equipment in the rack should be such that a hazardous
condition is not achieved due to uneven mechanical loading.
Important
This user guide contains information on the limitations regarding product use and function and
information on the limitations as to liability of the manufacturer. Read the entire guide carefully
5-Port Ethernet Gigabit PoE Switch
Quick Installation Guide
5-Port Gigabit PoE+ Switch (30W)

Table of Contents

Rev 1.0 01/03/2013 Page 1 OF 7
Page 2
Page 2
Page 3
Page 3
Page 4
Page 5
Page 6
Page 7

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the POE-5000 and is the answer not in the manual?

Questions and answers

Summary of Contents for GrandTec POE-5000

  • Page 1 Quick Installation Guide 5-Port Gigabit PoE+ Switch (30W) Table of Contents Introduction ………………………………………………….. Page 2 Power Over Ethernet (PoE) & Features ……..………….. Page 2 Unpacking and Installation ……… .……………………….. Page 3 Page 3 System Requirement……. .……………………………….. Front Panel /LED….…………………………………………. Page 4 Hardware Installation…...
  • Page 2: Introduction

    1. Introduction The 5-Port Gigabit PoE+ Switch is an unmanaged Gigabit Ethernet PoE+ switch designed to enhance workgroup performance while providing a high level of exibility. It provides 5 x 10/100/1000Mbps ports and 4 IEEE802.3at Power over Ethernet (PoE+) ports for workstation, It is an ideal solution for small o ce and home users to utilize a combination of Gigabit PoE and non-PoE device.
  • Page 3: Unpacking And Installation

    3. Unpacking and Installation Open the container and carefully unpack its contents. The case should contain the following items: • One 5-Port Gigabit Ethernet PoE+ Switch • One AC to DC Power Adapter • Quick Installation Guide. *If any item is found missing or damaged, please contact your local reseller for replacement. 4.
  • Page 4: Front Panel /Led

    5. Front Panel/LED/PoE Network Front Panel Power Uplink Port Act/Link PoE Ports Speed LED Display ☼ Light Blinking Slowly Inactive Blinking Fast Power LED LED on: Power ON / LED o : Power OFF. Speed (1 - 5) : 100 Mbps ☼...
  • Page 5: Hardware Installation

    6. Hardware Installation A. Power: Connect the AC Power cord to the power source and the DC power cord to the switch. B. Up-Link: Connect a CAT-5, 5e or 6 RJ-45 network cable from the Network or Router to an Up-Link port.
  • Page 6: Technical Speci Cation

    7. Technical Speci cations Standard IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3x Full Duplex Flow Control IEEE 802.3at Power over Ethernet Plus (30w) IEEE 802.3ab 1000Base-T Gigabit Ethernet (twisted-pair copper) Protocol CSMA/CD Ethernet: 10Mbps (half-duplex), 20Mbps (full-duplex) Fast Ethernet: 100Mbps (half-duplex), 200Mbps (full-duplex) Gigabit Ethernet: 2000Mbps (full duplex) Network Cables...
  • Page 7: Troubleshooting

    8. Troubleshooting 1> After connecting the Switch to a power outlet, the LEDs do not turn on. Check the connection of the power cord to the Router and the power outlet. Check that the power outlet is active. 2> When I connect a computer to the Switch's port, the Link/ACT LED turns on, but the 1000 LED remains o .

Table of Contents