Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Livewire Connections Manuals
  4. Gateway
  5. FB-10
  6. Quick start manual

Livewire Connections FB-10 Quick Start Manual

Hide thumbs Also See for FB-10:

Advertisement

Quick Links

Download this manual
Access Controller FB-10 Quick Start Guide
(for mini-VSAT Broadband
The following supplemental instructions explain how to connect
Livewire Connections' Access Controller to both a mini-VSAT
Broadband system (e.g., TracPhone
Fleet system (e.g., TracPhone FB250, FB500, FB150, F33, F55, or F77).
For complete setup and operation information, including advanced
configurations (e.g., firewall settings, port forwarding, remote access,
and access control), refer to the Access Controller's user
documentation.
NOTE: These instructions assume you have already installed both antenna
systems.
NOTE: Microsoft's .NET Framework is required to run the Access Controller
software. The Access Controller software installer will prompt you to
download .NET Framework from the Internet if it's not already installed on
the PC. At press time, the file size of the .NET Framework download was
approximately 870 KB. Please note that normal airtime charges will apply if
you choose to download this file via a satellite connection.
54-0688 Rev. A
sm
& FleetBroadband or Fleet connections)
®
V7) and a FleetBroadband or
Access Controller FB-10
Quick Start Guide
1

Advertisement

loading

Related Manuals for Livewire Connections FB-10

Summary of Contents for Livewire Connections FB-10

  • Page 1 Access Controller FB-10 Quick Start Guide (for mini-VSAT Broadband & FleetBroadband or Fleet connections) The following supplemental instructions explain how to connect Livewire Connections’ Access Controller to both a mini-VSAT ® Broadband system (e.g., TracPhone V7) and a FleetBroadband or Fleet system (e.g., TracPhone FB250, FB500, FB150, F33, F55, or F77).
  • Page 2 Access Controller FB-10 Quick Start Guide Step 1 - Wire the Access Controller Follow the applicable steps below to wire the Access Controller to your antenna systems. a. mini-VSAT Broadband: Connect the mini-VSAT Broadband system (e.g., TracPhone V7) to the Access Controller according to any of the diagrams on the following pages.
  • Page 3 Access Controller FB-10 Quick Start Guide Access Controller Wiring: TracPhone V7 + TracPhone FB250 or FB500...
  • Page 4 Access Controller FB-10 Quick Start Guide Access Controller Wiring: TracPhone V7 + TracPhone FB150...
  • Page 5 Access Controller FB-10 Quick Start Guide Access Controller Wiring: TracPhone V7 + TracPhone F33, F55, or F77...
  • Page 6 Access Controller FB-10 Quick Start Guide Step 2 - Run the Access Controller Software Follow these steps to install and run the Access Controller software on the customer’s primary onboard computer, which will control all Access Controller operations and setup. If desired, install the software on multiple computers to give them control as well.
  • Page 7 Access Controller FB-10 Quick Start Guide Step 3 - Configure a mini-VSAT Broadband Connection Follow the steps below to add a mini-VSAT Broadband connection (e.g., TracPhone V7) to the Access Controller’s interface. a. At the Internet Connections tab, select Add New Service.
  • Page 8 Access Controller FB-10 Quick Start Guide Step 4a - Configure a FleetBroadband Standard Connection Follow the steps below to add a standard FleetBroadband connection (via TracPhone FB500, FB250, or FB150) to the Access Controller’s interface. a. At the Internet Connections tab, select Add New Service.
  • Page 9 Access Controller FB-10 Quick Start Guide Step 4b - Configure a FleetBroadband Streaming Connection (Not Common) Follow the steps below to add a streaming FleetBroadband connection (via TracPhone FB500 or FB250) to the Access Controller’s interface. a. At the Internet Connections tab, select Add New Service.
  • Page 10 Access Controller FB-10 Quick Start Guide Step 4c - Configure a Fleet MPDS Connection Follow the steps below to add a Fleet MPDS connection (via TracPhone F77, F55, or F33) to the Access Controller’s interface. a. At the Internet Connections tab, select Add New Service.
  • Page 11 Access Controller FB-10 Quick Start Guide Step 4d - Configure a Fleet ISDN Connection Follow the steps below to add a Fleet ISDN connection (via TracPhone F77 or F55) to the Access Controller’s interface. a. At the Internet Connections tab, select Add New Service.
  • Page 12 Access Controller FB-10 Quick Start Guide Step 5 - Apply Changes When you are done setting up all of the desired connections, follow the steps below to save all of your changes. a. At the Internet Connections tab, select Apply Service Changes.