Related Manuals for AromaMist AI-5
Summary of Contents for AromaMist AI-5
- Page 1 AromaMist AromaMist AromaMist AromaMist Pump Model AI-5 Installation and Operation Manual rev. 3z.9505...
-
Page 2: Table Of Contents
AromaMist Pump Model AI-5 AromaMist AromaMist AromaMist Installation and Operation Manual Table of Contents Introduction………………………………………………….……. Safety and Operating Information……………………………… III. Pump Package Contents……………………………………….. Installation A. Location………………………………………………………. B. Mounting The Pump………………………………………… C. Electrical……………………………………………………… D. Plumbing……………………………………………………… E. Control (Aroma Switch)……………………………………... F. Typical Installation……………………………………………... -
Page 3: Introduction
Introduction Congratulations, you have just purchased the world’s most advanced aroma oil AromaMist AromaMist AromaMist AromaMist metering pump, the pump. This instruction manual covers all facets of the installation and operation of the AromaMist AromaMist AromaMist AromaMist pump including unpacking, mounting, electrical, plumbing, control, pump connections, and start-up. -
Page 4: Pump Package Contents
III. Pump Package Contents AromaMist Pump Package Contents AromaMist AromaMist AromaMist AromaMist AromaMist AromaMist AromaMist Pump B. ⅜” Discharge/suction tubing, 20’ C. 3-function valve D. Foot valve E. Ceramic weight F. ⅜” Vinyl priming tubing, 10’ G. ½” Brass T H. -
Page 5: Electrical
AromaMist AromaMist pump model AI-5 is a 120V AC pump and has a voltage regulated internal power supply capable of operating in the range of approximately 95 to 135 VAC. Use a supply voltage of 100 to 120 VAC for best results. The 3-wire grounded plug must be used with provided power supply module in a 3-wire grounded wall outlet. -
Page 6: Control (Aroma Switch)
NOTE: For convenient use during steambathing, an aroma switch mounted inside the steam room is most preferred. 2. Mounting Aroma Switch Make a 1⅝” diameter hole in desired control location. Route the aroma switch AromaMist AromaMist AromaMist AromaMist integral control cable from the wall cut out to the pump power supply module. -
Page 7: Typical Installation
F. Typical Installation AromaMist AromaMist AromaMist AromaMist G. Step By Step Pump Installation 1. Verify carton components and mount 2. Locate brand aroma oil and AromaMist AromaMist AromaMist AromaMist pump on a level surface. See details on remove cap. locating the pump on page 4 of this manual. - Page 8 AromaMist AromaMist AromaMist AromaMist G. Step By Step Pump Installation (continued) 3. Drill 2 holes in aroma container cap: 4. Beginning with the more rigid 20' one ⅜" hole for clear vinyl priming tube suction tubing, cut the required length and one "...
- Page 9 AromaMist AromaMist AromaMist AromaMist G. Step By Step Pump Installation (continued) 9. Remove intake valve tubing nut and 10. Cut required length of discharge red protective cap, slip nut on the tubing, remove discharge valve tubing suction tubing, secure suction tubing on...
- Page 10 AromaMist AromaMist AromaMist AromaMist G. Step By Step Pump Installation (continued) 15. All pump connections should appear 16. Run a 110V AC grounded outlet as detailed above. Steam head shown within 6’ of pump installation location for illustration purposes only.
-
Page 11: Start-Up
AromaMist AromaMist AromaMist AromaMist Start-Up - Primimg the pump AromaMist AromaMist AromaMist AromaMist CAUTION: Please read all 7 steps prior to priming the pump AromaMist AromaMist AromaMist AromaMist 1. Insert pump power supply cord into pump power supply module. AromaMist... -
Page 12: Operation Warnings
VI. Operation Warnings AromaMist AromaMist AromaMist AromaMist 1. Do not use a sharp object or fingernail to press on the pump switch. Sharp objects will penetrate the face plate and damage the aroma switch. AromaMist AromaMist AromaMist AromaMist 2. Do not pump unapproved aroma oils with the pump system. -
Page 13: Operation
VII. Operation AromaMist AromaMist AromaMist AromaMist During the steambath session, initiate the pump by pressing the mist icon below the on/off LED indicator light on the aroma switch. Once activated, the red LED will light and the aroma oil will begin to flow into the steam line. -
Page 14: Troubleshooting
VIII. Troubleshooting Problem Cause Remedy Pump Air Trapped in suction Straighten suction line so as to eliminate high does not line spots achieve or maintain Foot Valve Inspect foot valve screen and assure that foot prime contaminated or valve is in a vertical position below fluid level improperly installed Excessive lift Maximum suction lift is 5 feet with water or fluids... - Page 15 Page 15...
Need help?
Do you have a question about the AI-5 and is the answer not in the manual?
Questions and answers