Page 3
Unpack the ITNS‐400 Negative Film Holder User Manual ITNS‐400 Slide Film Holder Clean brush Quick Installation Guide CD‐ROM ...
Page 4
II. Install a film/slide into holder Install the slide into holder: Open the slide holder as illustrated Put slide into positive slide slot 3. Close the film holder ...
Page 5
Install the negative film into holder: 1. Open the film holder as illustrated Install film into negative film slot 3. Close the film holder To avoid mirror image, follow the serial numbers (from left to right) on top of film when install negative film into holder. Figure 1...
Page 6
If the image is upside down [see fig. 2] , the image can be corrected by “Rotate” function in AP after capture [see fig. 3]. Figure 2 Figure 3 ...
Page 7
III. ITNS‐400 Plug in USB cable to computer without installing any necessary driver. When the status icon on the left button corner shows information “Your device is ready to use”. The scanner is now ready to use. ...
Page 8
IV. Use ITNS‐400 1. Put Film into film slot 2. Insert the holder into ITNS‐400 ...
Page 9
3. Make sure USB cable is connected to ITNS‐400 and PC 4. On Desktop double click on “Launch Image Scan Tool” icon ...
Page 10
5. Click “Image Scan Tool” to enter operation interface as below 6. Press “Copy” hard button to capture the image to store in thumbnail. ...
Page 11
Click on function of mirror, rotate, color and brightness control to make image to prefer state. 8. Press Save to store captured images to hard disk. The images stored in thumbnail bar is cleared after save. ...
Page 12
9. Retrieve saved images from the hard disk to further review and edit. ...
Page 13
To obtain service, the purchaser MUST present an original sales receipt / proof of purchase. Please contact us at www.ithomeproducts.com to request an RMA (Return Material Authorization) number to return products for service or replacement. Returns without an RMA number on the package will be refused and returned to sender. Upon receipt of the returning item and our full inspection (IT) may issue a replacement to customer for the same item or of one that has equivalent value and features. To return an item, supply full name, return address, phone number, item purchased, receipt of purchase and reason for return to obtain RMA number. All returns must be in the original packaging or reasonable substitute to prevent damage. Customer “Must” include full name, shipping address and telephone number inside of package. No return will be shipped back to a PO Box or APO address. Please include your check or money order in the amount of • USD$5.00 for items $10.00 to $39.99 (Price Paid Per Unit) • USD$10.00 for items $40.00 to $99.99. (Price Paid Per Unit) • USD$16.00, for items $100.00 and up. (Price Paid Per Unit) • Shipping fees are non‐refundable to be payable to Innovative Technology Electronics Corp.(for handling and return shipping charges) (IT) will not be responsible for delays or unprocessed claims resulting from a purchaser’s failure to provide any / all of the necessary information. Send all inquiries or RMA request via our website www.ithomeproducts.com/support. Innovative Technology Electronics Corp. 1 Channel Drive Port Washington, NY 11050 Toll free: 1‐877‐483‐2497 Website for support: www.ithomeproducts.com/support There are no express warranties except as listed above. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CUSTOMER, (IT) SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal ...
Instructions shall caution users that modifications not approved by the party responsible for compliance could void user's authority to operate the equipment. The following or equivalent as appropriate: “NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.