Laser Pegs 1070 Model Instructions

Please read manual before you begin! Failure to
1070
follow this manual's instructions may result in
damage to the 3D Lite Board®, AC Adapter and/
or Laser Pegs®. Not adhering to these directions
For Boys And Girls
will void the manufacturer's warranty.
Ages 5 And Up
Packing has to be kept since it contains
57 Models+
important information.
WARNING:
CHOKING HAZARD
Any creation you can build
-
Small parts.
LIGHTED
Not for children under 3 yrs.
Do not submerge in water.
CONSTRUCTION SET INCLUDES:
®
• 35 Laser Pegs
• 225 Construction parts
• 3D Lite Board ®
• Instruction Manual
Construction Compatible
Requires 3 AA Batteries
Compatible with other construction kits
Batteries NOT
EN71, RoHS COMPLIANT
Included
This product complies to
all safety requirements
MODEL INSTRUCTIONS
All additional model instructions can
be downloaded at www.LaserPegs.com
Laser Peg® Parts List
x2
There is No LED In The 90 Degree Peg
x3
x7 x2 x1 x1
Y PEG
x2
45° PEG
SQUARE SQUARE STRAIGHT STRAIGHT
PEG M-M PEG T-PEG
STRAIGHT
90° PEG
HALF-O x4 x1
M-M PEG
PEG
Color Each Laser Peg® is color coded on the circuit board inside
Code each shape. There is No LED In The 90 Degree Peg.
Laser Pegs ® Stackable
Laser Pegs
® link that
allows you to connect to
other construction kits.
Construction Parts List x4
x8
x2
x6
x12
x4
x8
x16 x8
x6
x16
x6
x8
x8
x6
x20
x6
x8
x16
x8
x6
x6
www.LaserPegs.com
This manual is copyright and cannot be reproduced or used online without Laser
Pegs®Ventures LLC permission. Copyright 2012 © All Rights Reserved US Patent
#7,731,558 Additional Global & Multiple Patents Pending. Laser Pegs®Ventures LLC.
8304 Consumer Ct Sarasota FL. 34240. Contact: Support@LaserPegs.com
Connecting Pegs
To construct with Laser Pegs®, slide two pieces together to form a
connection. Slide each piece on and off smoothly. To build away from the
Triangle Power Base, use the peg cord in one of the top three peg holes to
illuminate your model! The 90° pegs are essential to construction but they
DO NOT ILLUMINATE.
Connect Laser Pegs® to 3D Lite Board ®
Peg Holes
Peg Holes
of ASTM F 963
Press button to turn on/off
Push button to cycle through 3 different light settings.
Power button
Connecting an AC Adapter
Plug AC Adapter plug into the side of the 3D Lite Board®.
AC Adapter
Connection
x8
Stackable
x4
Remove all batteries from laser Pegs®
3D lite Board ® power base before using
WHEEL PEG
5 volt AC adapter.
*To avoid short-circuits, keep metal objects
and other un-authorized materials from
obstructing the peg holes.
The AC Adapter used with the power base are to be regularly examined for
damage to the cord, plug, enclosure and other parts, and in the event of such
damage, they must not be used until the damage has been repaired.
Battery
Compartment
®
x6
Batteries NOT
Included
x6
Battery Compartment
x4
Requires (3AA) Batteries
x4
When Using Batteries
1. Remove screws.
x1 2. Place three AA batteries in the correct position - as displayed inside the
3D Lite Board®.
x8 3. Push RED button to turn on!
4. Do not mix old and new batteries.
x8
5. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-
cadmium)batteries!
6. Exhausted batteries are to be removed from the power base.
7. Never connect more than 200 Laser Pegs®
8. Non-rechargeable batteries are not to be recharged.
9. Rechargeable batteries are only to be charged under adult supervision.
10. Rechargeable batteries are to be removed from the toy before being
charged.
11. Batteries are to be inserted with the correct polarity.
12. The supply terminals are not to be short-circuited.
3D Lite Board®
Power Button
3 light settings.
Press power button to
change light setting.
AC Adapter
INPUT is on side of
3D Lite Board®.
Hinge
Pull outward
to open.
*AC Adapter
sold seperatley.
NEVER place AC Adapter
Plug into top Peg Holes
Tote Box
Never connect more than 200
Designed for storage
Laser Pegs® when using a 5 volt
(2000mA) AC Adapter.
of Laser Pegs® parts.
Place batteries in
the correct position
when using.
WARNING! Each Laser Peg® draws current from the batteries. Therefore,
the more pegs you use, the quicker you will deplete your battery power!
As the power weakens, the current will slowly fail and some Laser Pegs®
will illuminate (typically the reds and yellows) and some won't. When the
Laser Pegs® dim the Laser Pegs® are not broken, they just need stronger
batteries or an AC Adapter.
You have 3 simple options...
1. Use a 5 volt AC Adapter –available from www.LaserPegs.com
2. Change the batteries.
3. Use high quality batteries. They will last a little longer, but they will
still deplete rapidly the more laser pegs you connect!
DINOSAUR — A typically-large
Peg Holes
reptile of the Mesozoic era.
DINOSAUR
Model
Difficulty
Level
Battery Compartment
Requires (3AA) Batteries
A
STEP
1
Use Phillips head
screwdriver.
STEP
2
STEP
3
STEP
4